57: Design a T-beam having cross section shown in figure belowaccording to ACI code requirement. The beam is simply supported on span1914of (7.31m), The is subjected to service dead load (48.80 kN/mm) (includingself-weight), and service live load (25 kN.m), Assume the designer intendsdnesto use: fe-21 MPa, fy=414 MPa and bf= 1 m. Use two layer ofreinforcement)at lanCOSM0.09mmRÝM OC¹0.3 m²1000-0.55 m

Service dead load = 48.8 KN/mService live load = 25 KN/mBeam span = 7.31 mf'c =21 Mpafy = 414 Mpabf…

: Design a T-beam having cross section shown in figure below according to ACI code requirement. The beam is simply supported on span of (7.31m), The is subjected to service dead load (48.80 kNm) (including 10 self-weight), and service live load (25 kN.m), Assume the designer intends des neu to use: fe 21 MPa, fy=414 MPa and bf= 1 m. Use two layer of reinforcement) COS-FERS

: Design a T-beam having cross section shown in figure below according to ACI code requirement. The beam is simply supported on span of (7.31m), The is subjected to service dead load (48.80 kNm) (including 10 self-weight), and service live load (25 kN.m), Assume the designer intends des neu to use: fe 21 MPa, fy=414 MPa and bf= 1 m. Use two layer of reinforcement) COS-FERS

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.10.7P

See similar textbooks

Similar questions

For a simply supported beam with span 5.5 m , determine the area of steel required to reinforced the beam(250*500) mm if it subjected to service dead load (including to self-weight) (15.3 kN/m) and service live load (36 kN/m) use f’c = 27.5??? & fy 414MPa
The cantilever beam shown is aW10 × 77 of A992 steel. There is no lateral supportother than at the fixed end. Use an unbracedlength equal to the span length and determinewhether the beam is adequate. The uniform load isa service dead load that includes the beam weight,and the concentrated load is a service live load.
A simply supported beam is laterally supported at its ends and is subjected to the following serviceloads: Dead Load – 5.8 kN/m (including the weight of the beam)Live Load – 14.6 kN/mIf Fy = 345 MPa, is W360x134 adequate? Span Lengtha. L = 30 ft
Find lightest W14 for L = 20’ and w = 3k/ft AND concentrated loads of 6k @ 4ft o.c. E = 29,000ksi, Fb = 30ksi and Fv = 20ksi
A W12x65 is to be used as a simply supported beam on a span of 20 ft with lateral support at the ends only. The beam is required to support a plastered ceiling. If the dead load is 0.20kips/ft (including beam weight), what is the maximum uniform service live load permitted on the beam, using A992 steel? What percentage increase in live load can be gained if the beam is A572 Grade 65 steel. Use AISC 360-16 specifications
kindly solve this question|? A W 5300*101 of Steel Section (fy= 345 MPa & fu= 450 MPa) is used as simply supported beamwith a span of 15 m. The dead load is the summation of the super dead load (7 kN/m as uniformload) and the beam weight. In addition to the dead load, a uniform live load is applied to the beam.If the lateral support is provided at 3-meter intervals, what is the maximum service live load inkN/m that can be supported.
Using the ASD method, pick the least-weight beam. Fb = 24ksiFv = 14.5ksiDefl limit = L/360 A cantilever beam 6’ has a concentrated load of 12.3k at its unsupported end.
A W 5300*101 of Steel Section (fy= 345 MPa & fu= 450 MPa) is used as simply supported beamwith a span of 15 The dead load is the summation of the super dead load (X1=9 kN/m as uniform load) and the beam weight. In addition to the dead load, a uniform live load is applied to the beam. If the lateral support is provided at 3-meter intervals, what is the maximum service live load in kN/m that can be supported.
A simply supported beam with a span length of 45ftis laterally supported only at its ends and issubjected to the following service loads:Dead Load = 400 lb/ft (incl. the weight of the beam)Live Load = 1000 lb/ftIf Fy = 50 ksi, is the W 14 x 109 adequateconsidering limits of moment, shear and deflection?
A Wx35 steel column has an unsupported height of 6m. Use A36 steel with Fy = 248 MPa and E = 200,000 MPa. A = 6504 rx=88.9 mm ry = 51.56 mm Determine the safe axial load if both ends are hinged.
The loads for a 40’ simply-supported beam are as follows: • Dead Load, D = 600 plf • Live Load, L = 1000 plf Two load combinations need to be considered: a. 1.4D b. 1.2D + 1.6L Given these two load combinations, what is the maximum reaction to be used for the design of the member for strength, assuming the beam is simply-supported? What load (i.e., load combination) should be used to check the maximum service deflection?
Compute the design moment strength of the beam section described below if fy = 420 MPa, fc’ = 21 MPa. d = 650 mm d’ = 70 mm b = 450 mm As’: 3-28mm dia. As: 4-36mm dia