Problem #1 6 ft 4ft 50 lb/ft 8 3ft 3ft 30° 80 lb The structure shown is pin supported at A and roller supported at C and loaded as shown. Determine the internal normal force, internal shear force, and internal bending moment at B. BE CAREFUL TO DRAW GOOD FREE BODY DIAGRAMS AND TO WRITE GOOD EQUILIBRIUM EQUATIONS.

Problem #1 6 ft 4ft 50 lb/ft 8 3ft 3ft 30° 80 lb The structure shown is pin supported at A and roller supported at C and loaded as shown. Determine the internal normal force, internal shear force, and internal bending moment at B. BE CAREFUL TO DRAW GOOD FREE BODY DIAGRAMS AND TO WRITE GOOD EQUILIBRIUM EQUATIONS.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations.) Ax=0 Ay=? By=? Magnitude and direction
Q9c. For the beam below, the point loads and distances are as follows: F1 = 11. 25 kN, F2 = 11.25 kN and F3 = 4.50 kN L1 = 2.25 m, L2 = 4.50 m, L3 = 4.50 m and L4 = 2.25 m Determine the bending moment at D. Give your answer in kilonewton metres (kNm) to two decimal places.
For the frame shown, determine the support reactions. EI is constant.Use the force method. I have a correct answer, it is: VA = 36.30 kN (↑); HA = 19.30 kN (→); VB = 18.70 kN (↑); HB = 11.30 kN (←). To the left); B (right). I don't know how to get to this result, please show me how to get there step by step
Determine the bending moment at B. if w =39 kN/m, L =8Round off the final answer to three decimal places.
(i) A tie bar is 2.5 m long, has a circular cross section of 50 mm in diameter and is subjected to a force of 250 kN. Given that Young’s Modulus E = 209 kN/mm2 and Poisson’s Ratio ν = 0.3 calculate the change in volume of the bar when loaded. (ii) Draw the shear force and bending moment diagrams for the cantilever beam shown in the image attahced clearly indicating all significant points.
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
Replace the force F having a magnitude of F = 50 lb and acting at point A by an equivalent force and couple moment at point C.
calculate the Axial Force in kips on member BC if the given 30kip and 20kip loads from the figure are both replaced by 89kips and 31kips respectively. Express your answer in 2 decimal places. Include (-) negative sign if the axial force is compression.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
analyze the structure using three moment equation and answer the question and provide the following requirements. What is the approximate Moment at support A? in kN.m A. 79.86 B. -10.98 C. -73.28 D. 73.28 E. -27.95 F. 0 G. -79.86 H. 10.98 I. 27.95
given w = 8.2 kn/m and p = 15 kn for the beam below Calculate the vertical reaction at support A now. Provide your answer to 2 decimal places. Consider an upwards force as being positive, however only include a sign if the reaction is negative i.e. acts vertically down. Do not provide any units in your answer. Vertical reaction at A [kN] =
F=30 kN single load, M=34 kN.m moment and w=10 kN/m distributed load are acting on the beam whose loading condition is given in the figure. Point B is located just to the right of the application point of force F and moment M. The length L is also given as L=5 m. According to this;Question1-A) Find the support response (Dy) at point D. (Write your result in kN.)Question1-B) Find the support response (Ay) at point A. (Write your result in kN.)Question1-C) Find the shear force (VB) at point B. (Write your result in kN.)