Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using "Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. 9 Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = _k Ohms

Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using "Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. 9 Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = _k Ohms

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

An amplifier is formed by cascading three identical operational-amplifier stages, as shown . (a) Replace each op amp circuit with itstwo-port representation. (b) Use the circuit model from part (a) to find the overall two-port representation (Av, Rin, Rout) for the complete three-stageamplifier. (c) Draw the two-port circuit corresponding to the complete three-stage amplifier.
Show the connection of an LM124 quad op-amp as a four-stage amplifier gains of +20, -22, -39 and -25.Use a 500 k resistor for all stages. What output voltage results for an input of V1 = 100 V? i need the answer in 30 minutes please
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Rin in ohms?Rin = ____ ohms
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
Derive the appropriate equation for an inverting amplifier with op-amp and provide the values of resistances to obtain the gain equal 3 (kvR -> infinity, Vr -> 0)
For the circuit shown above, find the gain (vo / vi). Make simplifying assumptions about the OP-AMP such as v+= v- but you must state the conditions for which this is true. Please as soon as possible！
Select true or false for 1 and 21 Op amp component is temperature limited due to maximum output current2 The input offset voltage affects the value of the opamp output and is caused by internal non-idealities in the transistors and resistors. 3 What is the use of an op amp in voltage follower? Select one:a. It is the ideal bridge to couple any stages without affecting the voltage.b. It is ideal for maximum power transferc. Allows a small signal to be amplified with high gaind. voltage attenuation 4. It allows to eliminate the problem of variability in the gain parameter of the circuit:Select one:a. The load RLb. High input impedancec. feedback loopd. decoupling capacitors 5 Complete: The output current is limited due to the _____ that the opamp can handle, while the ______ is limiting due to the maximum bias level supported by the transistor.
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
Convert the inverting amplifier shown to thetransresistance amplifier as shown(66) using a Nortontransformation of vi and R1. What are the expressionsfor iTH and RTH? Write a expression forthe gain vo/vi.
Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? fot third stage)
Design an instrumentation amplifier like that pictured in Figure 1 by choosing appropriate resistor values Ra1, Ra2, RG, and R1, R2, R3, and R4, such that the overall differential gain is as close as possible to 25. Choose values in the 10s of k ohm range. Divide the gain between the stages as you wish, but justifyyour design choices. (Q1) Explain the chosen values and give a rationale.
An amplifier is required with a voltage gain of 35,000 and will be designed using a cascade of several C-E amplifier stages operating from a single7.5-V power supply. Estimate the minimum number of amplifier stages that will be required to achieve this gain.