Design an 8-4-2-1 BCD code converter to drive a seven-segment indicator. The four inputs to the converter circuit (A, B, C, and D) represent an 8-4-2- 1 binary-coded-decimal (BCD) digit. input D с B A Circuit to be Designed a b C d e f 8 7-segment display The invalid BCD combinations 1010 through 1111 will give "E", error. Design your circuit using minimum number of gates. Test your design using logic work.

Design an 8-4-2-1 BCD code converter to drive a seven-segment indicator. The four inputs to the converter circuit (A, B, C, and D) represent an 8-4-2- 1 binary-coded-decimal (BCD) digit. input D с B A Circuit to be Designed a b C d e f 8 7-segment display The invalid BCD combinations 1010 through 1111 will give "E", error. Design your circuit using minimum number of gates. Test your design using logic work.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

When the value of the four-bit N number consisting of W, X, Y, Z variables is N <3 or N> 6, the circuit with a logic 1 output is designed with 8x1 MUX. When the W, X, Y variables are mutually connected to the S2, S1, S0 selection terminals of the multiplexer, in which case are the signals to be connected to the input terminals of the multiplexer correctly? (The variables will be used in the given order and W is MSB. The signals to be applied to the input terminals are written from I0 to I7.)
i) Construct a 4-to-1 Multiplexer and provide a picture or snapshot of the circuit here. ii) Use the multiplexer you have constructed in part i)to implement this circuit: F(A,B,C) = ∑m(0,3,4,7) Provide a truth table and a picture or snapshot of the circuit here.
Please answer this question in 10 mins i will surely rate your answer. 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs bb A3, A2, A1, A0 represent the 4-bit binary number. Another input is a control signal C. The circuit has outputs assumed to be X3, X2, X1 and Xo, which represent the 4-bit number X. When C=0, X=A+1 and when C=1, X=A+2. Assume that the inputs for which X > (1111)2 will never occur. Show the design steps in detail including truth tables, K-Maps, logic equation minimisation. Finally, design this circuit using only NAND gates and inverters .
2) Design a 2-to-1 multiplexer in which the inputs and outputs consist of single bits. Provide the truth table for this multiplexer using IN0 and IN1 for the two inputs, S for the select line and OUT for the output correctly. Obtain the minimal standard sum-of-products expression for the output correctly. PS: Please answer Number 3 from or after number 2 3) Obtain the schematic diagram for the mux designed in 2). Use proper conventions as to the labelling of part numbers, instance numbers and pin numbers correctly.
Question:If you have two functions F(a,b,c) and G(a,b,c) to implement, what mux size and how many muxes would you need to implement F & G?My Comments:Is it as simple as using two 4-1 multiplexers because it will handle the 6 inputs? Or am I not understanding the function of a multiplexer?
choice correct answers analogReadResolution() instruction accept bit resolution up to 16 12 32 the maximum of the programmed board - For Arduino ZERO, using 2.23 V built in reference, what is the input code if the default bit resolution was used for Vin = 1 V? 458 1836 459 1837 - For memory address (133F7) h with offset of (2031) h, what is the segment address? 15442 113C 33701 135F41 - What is the input for Arduino UNO if the input voltage is 3.25 V? Assume defaults 1008 644 645 1007
logic circuit please snswer as soon as possible
Find the answers to the following questions? a) Find the excess-3 code of (152) Base 10.b) Convert binary to grey code 0101011.
9. 1) Implement the Boolean function F(A, B, C, D) = II(0, 3, 4, 6, 9, 12, 14) with a 4 - to - 1 multiplexer and external gates. Connect inputs A and B to the selection lines. Express F as a function of C and D for the data inputs of the multiplexer. These functions may have to be implemented with external gates
A BCD code is being transmitted to a remote receiver. The bits are A3A2A1A0 with A3 as the MSB. The receiver circuitry has a BCD error detector circuit that examines the received code to see if it is a legal BCD code. Design a circuit to produce 1 for any error condition.
I) Convert from Binary to Decimal a) 10100001112 Date of submission: _______________________ II) Using Double Dabble method, convert from Decimal to Binary (a) 22810 (b) 175.1010 III) Convert from Hexadecimal to Decimal (a) 1CED716 (b) C1E18A.E8D916 IV) Convert Decimal to Hexadecimal (a) 134510 (b) 9176.5410 V) Convert from Binary to Hexadecimal (a) 101011010101112 (b) 11101111101.0100101012 VI) Convert from Hexadecimal to Binary (a) 78EBC516 (b) AEDC2.12B16
8- Convert the following Gray codes (1000)to binary? 9- How many bits are required to represents the decimal numbers in the range from( 0 to 999 )using : 1- straight binary code? 2-Using BCD code? 10 Determine the codes that are entered from the computer’s keyboard when the following basic program statement is typed in. also express each in hexadecimal notation.10 Add “X=A+B”;X