DESIGN SPECIFICATION 1 The input impedance to a certain amplifier at a frequency of 2 GHz is 30-j250. Match this impedance to a source impedance of 50 2 using a conventional quarter-wave impedance matching transformer, connected at the nearest resistive point to the load and implemented with microstrip. All microstrip dimensions are required in mm. The substrate material to be used, is Rogers® type RO4003 with a relative dielectric constant of 3,38 and a thickness of 0,81 mm.

DESIGN SPECIFICATION 1 The input impedance to a certain amplifier at a frequency of 2 GHz is 30-j250. Match this impedance to a source impedance of 50 2 using a conventional quarter-wave impedance matching transformer, connected at the nearest resistive point to the load and implemented with microstrip. All microstrip dimensions are required in mm. The substrate material to be used, is Rogers® type RO4003 with a relative dielectric constant of 3,38 and a thickness of 0,81 mm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive the following. Assume an ideal current source a) Input Impedance
The diagram shown below is a typical tuning circuit. Considering this circuit comprises a transformer (with a coil ratio of 20:1 and an HV side voltage of 240V ), a capacitor of impedance -j20Ω, an inductor of impedance j40Ω, and a 50Ω resistor, determine: the current supplied by the source the impedance seen at the supply (HV side) the power dissipated by the resistor the operating power factor of the fitting If the capacitor is now removed from the above circuit and is placed in parallel with the secondary of the transformer, redraw the circuit diagram and recalculate parts a. to d. in question (i). Draw the phasor diagram for both series and parallel RLC circuits in parts (i) and (ii). Discuss the effects of changing the capacitor connection in parallel on the power factor of the circuit. State the benefits of using the transformer in the above circuit. Explain the operating principle of the transformer with particular reference to electro-magnetic…
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
If vt = 230cis40degrees. determine the equivalent impedance.
What is power factor correction and whatt is your conclusion?
Is it possible to measure the phase-shift angle in an AC single-phase circuit by an indirect method using an ammeter and a voltmeter? - Yes, but an instrument must be added to measure the active resistance of the load. - Yes, but an instrument must be added to measure the active power dissipated by the load. - Yes, but an instrument must be added to measure the frequency.
Determine input impedance Zi and voltage gain Vo/Vsig. Derive the formulae used
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
At amplifier has an output impedance of Z of 70 + j35 ohms. What value of load impedance will permit maximum power transfer?
1. PLEASE SOLVE AND SHOW YOUR DETAILED SOLUTION WITH FBD. A parallel circuit consisting of a resistor, an impedance coil, and a capacitor of negligible loss is connected across a 120-volt 25-Hz supply and takes a current of 4.3 amp. The current to the resistor is 3.6amp, that of the capacitor 2.5 amp, and that to the impedance coil, 3.2 amp, Determine the power-factor angle and power of the entire circuit.
Write the nonlinear function to find the ?(lowercase omega) that results in an equivalent impedance of 20 Ωfor the following AC circuit with the given parameters:
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.