Determine 8000 N 1500 N/m a) the maximum shear stress, along the beam, b) the maximum tensile bending stress along the beam, c) the maximum compressive bending stress along the beam. d) If the top board (20 mm x 60 mm) is connected with the nails to the below part, determine the maximum allowable spacing s, if each nail can resist a shear force of 1.5 kN. -0.4 m - 0.3 m -0.4 m Cross Section -60 mm- INA = 1.36 (10)-6 m² 20 mm A1 30 mm N.A. 60 mm y= 50 mm A2 20 mm

Q: Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P…

A:

Q: Spar webs develop shear stresses which resist? a. Bending shear force b. Torsional Moment c. Both…

A:

Q: 5 m 5 m 2m 2 m 12 kN 4 kN 20 C 12 -20 12 -4 kN Shear Diagram 1. Add file LLI

A: Load Diagram and BMD

Q: The beam is subjected to a shear of V = 39 kN. Set 300 mm Part A A 20 mm Determine the web's shear…

A: Given Data: The value of Shear force is V = 39 kN. The second moment of inertia of the section can…

Q: Tor each segment of the beam, lerive the shear force and bending noment values.

A:

Q: Q2. Calculate the maximum bending stress developed. Is it safely designed (Fb = 30 ksi? 4" 4' Beam…

A: The free body diagram of the beam is as follows.

Q: The slope joining points (4, 0) and (1, -2) is

A:

Q: Shear and Moment Diagram 1. Draw the Shear and Moment Diagram. 20 kN III 10 KN 5m SORN m 10 m 20 kN…

A: To determine the shear force and bending moment diagram for the given loading.

Q: - 3 ft 6 ft -3 ft- 2 in. 6 in. Lin 2 in, I in. Part A Determine the absolute maximum shear stress in…

A: Given:- Beam To Find :-  Absolute maximum shear stress in beam.

Q: What are the Internal Resultant Loadings?

A: Answer - Internal loads:-  Internal loads come into play when external load is applied on the member…

Q: Where should the internal resultant shear force be directed?

A: Direction for the internal resultant shear force will be opposite to the net force acting on the…

Q: 1. Draw the Shear and Moment Diagram A В MA 10 kN/m 2 m

A:

Q: For the beam shown in the figure, locate the point of zero shear from point A. Express your final…

A: First draw the shear force diagram for the following beam From this diagram assume that the point…

Q: A10C) Shear force and bending moment are . .force, and ... moment. a. internal, external. O b.…

A: Let us discuss about shear force and bending moment.

Q: Q1: Draw the following readings, which represent the relationship between the mass and the rate of…

A: According to the question, L=length of beam=60cm b=breadth of beam=2.5cm d=depth of the beam=05cm…

Q: 6 AN/m Draw the normal, shear and bending moment diagrams. 30m 3.0m 3.0m 9.0m

A: In this problem, it is asking the normal, shear and bending moment diagrams for beam BD.

Q: A beam is constructed from two i-sections as shown in Fig. Determine the maximum shear stress if the…

A:

Q: 15m 20 MFa 1. If the maximum bending stress in the shown beam is (Omax=20 MPa),the normal stress at…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Q-3] (7 Marks) Determine the resultant force on beam below and specify where it acts on the beam…

A: Draw the schematic diagram of the beam.

Q: 19. AT-section of a beam, as shown in Fig. 5.44, is subjected to a vertical shear force of 100 kN.…

A:

Q: Q1. Determine height (h) of the beam shown in Fig.(1), if the flexural stress is not the minimum 5…

A: Given data as per question Point load applied on the beam =5KN UDL applied on the beam =2.5 KN/m…

Q: F1 F2 M Determine the shear force and bending moment in the beam. Use F1 = 1100 N, F2 = 900 N, M-900…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: Q2-The tubular shaft is to have a cross section such that its inner diameter and outer diameter are…

A:

Q: = Draw the shear and bending moment diagram, where p 8 kip.

A:

Q: -What is the ratio of maximum shear stress to average shear stress for a circular section?:- (a) 2…

A: Given data,  Section is circular,  Need to calculate ratio between τmax and τavg

Q: X= Your Registration No Ib/ft C: 7 ft 4 ft R2 R Fig 1.1

A: Given: Length of beam AC (l)=11 ft . Uniform varying load (w) at section AB =130 lb/ft  .…

Q: Given: P=1.8a kN Area(BE)-150a mm? Area(CF)=150a mm? E=200 GPa Required: Change in length of CF? 18a…

A: Assuming, a=0

Q: Q. 1: A cast iron bracket subjected to bending has a cross-section of I-shape with unequal flanges…

A:

Q: W 24 x 94 beam is subjected to a shear force of 900 kN.   Properties: A = 17,870 mm2 d = 616.97…

A:

Q: From the given beam below, Iocate the point where the shear is zero from point A. w = 3 kips/ft %3D…

A: Given: The intensity of load over entire beam, w = 3 kips/ft

Q: 17C) Determine the bending moment and shear force at C. 16 KN/m A 4 m 10 m

A: The FBD for the beam is given below,

Q: The following picture shows part of a beam section which has been structurally idealised. The skins…

A: Shear flow is defined as the applied shear stress over a distance in a thin walled structure. The…

Q: A 6. A built-up wooden beam is subjected to a vertical shear of 6 kN. It is made 2 сm by gluing…

A:

Q: Q1: Check the adequacy of the beam shown in Fig (1-a) with section shown in Fig (1-b) at section B-B…

A: Data given-  f'c = 28 MPa  fy = 420 MPa  w = 20 kN/m

Q: a Determine the resulting bending stress. b. Safety factor against bending

A: Given: Module,  Pressure angle,  Pinion speed, Load,  Teeth on pinion,   Face width,

Q: 2gru i Henuz cevaplanmadı 5,00 uzerinden işaretlenmiş y F Soruyu işaretle H The internal shear force…

A:

Q: Q-1 .Construct the shear force and bending moment diagram for the beam shown below. 150N 75N 50N |C…

A:

Q: Assume that w = 39 N/m, L = 4.5 m, and El = 20210 Nm2 for the beam. Find the slope at the portion of…

A:

Q: Draw the shear and bending moment diagrams for the beam with loading as shown below. Label all…

A: Draw free-body diagram of the given loaded beam. Apply force equilibrium in horizontal direction.…

Q: 5 kN/m |A IC B 3 m Determine the value and direction of the internal normal force, shear force, and…

A: The free body diagram for member ABC is given below,

Q: ple 2: Draw the shear force and bending moment diagrams for the ever beam as shown below. by the…

A:

Q: 72. KN/m 54 KN 90 KN し↓de 270 KN-mD A RI - zm - E 2m + 2m t imt zm 3m R2

A: Given Data: Length of the beam, L=12 m

Q: ! Required information A plate of 2-mm thickness is bent as shown and then used as a beam. The beam…

A:

Q: (Q2) Determine the maximum normal stress due to bending of the beam loading show 5 kN 20 kN/m 50 mm…

A:

Q: The beam is subjected to a uniformly distributed load. What is the maximum magnitude of the average…

A:

Q: A beam having a T shaped section is subjected to a vertical shear force of V = 10,000 N. The cross…

A:

Q: The beam is subjected to a shear of V = 31 kN. Set 300 mm Part A A 20 mm -20 mm Determine the web's…

A: As per given Question we have determine  Determine the web's shear stress at A. Determine the web's…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.