Determine a set of principal axes and the corresponding principal moments of inertia of the beam's cross- sectional area shown in the figure below with respect to the beam's cross-sectional centroid, C. Indicate by means of a sketch the position of the principal axes with respect to the x-y axes. 60 mm C 20 mm 20 mm 10 mm 60 mm 10 mm - 100 mm 10 mm

Determine a set of principal axes and the corresponding principal moments of inertia of the beam's cross- sectional area shown in the figure below with respect to the beam's cross-sectional centroid, C. Indicate by means of a sketch the position of the principal axes with respect to the x-y axes. 60 mm C 20 mm 20 mm 10 mm 60 mm 10 mm - 100 mm 10 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.4P: The moment of inertia of the plane region about the x-axis and the centroidal x-axis are Ix=0.35ft4...

See similar textbooks

Similar questions

Using integration, compute the polar moment of inertia about point O for the circular sector. Check your result with Table 9.2.
The moment of inertia of the plane region about the x-axis and the centroidal x-axis are Ix=0.35ft4 and Ix=0.08in.4, respectively. Determine the coordinate y of the centroid and the moment of inertia of the region about the u-axis.
Using Ix and Iu from Table 9.2, determine the moment of inertia of the circular sector about the OB-axis. Check your result for =45 with that given for a quarter circle in Table 9.2.
The moments of inertia of the plane region about the x- and u-axes are Ix=0.4ft4 and Iu=0.6ft4, respectively. Determine y (the y-coordinate of the centroid C) and Ix (the moment of inertia about the centroidal x-axis).
The flanged bolt coupling is fabricated by drilling 10 evenly spaced 0.5-in. diameter bolt holes in a steel plate. The radii of the plate and bolt circle are 5 in. and 4 in., respectively. Determine the percent reduction in the polar moment of the area about point O due to the drilling operation.
For the surface shown in the figure below, determine:a) The xc and yc coordinates of its centroid;b)The moments of inertia and product of inertia in relation to the centroidal axes x' and y' (axes parallel to x and y , which pass through the centroid);c)Using Mohr's circle, the new moments and product of inertia obtained by rotating these centroidal axes by 35° counterclockwise.
Find the Moment of Inertia of the plate as shown in figure, passing through its centroid with reference to Y -Y axis. Where b1 = 55 mm, d1=110 mm, b2=160 mm, d2=30 mm, b3=65mm, d3=24mm. The value of is (unit in mm) = ______________ Answer for part 1 The value of is (unit in mm) = ______________ Answer for part 2 The value of total for the given plate is (unit in mm4) =________________ Answer for part 3
Determine the principal moments of inertia for the beam’s cross-sectionalthe area is shown in Figure with respect to an axis passing through the centroid C.
find1. The principal axes through the centroid of the section 2. principle moments of inertia
Determine the product of inertia of the beam’s cross-sectional area, shown in Figure, about the x and y centroidal axes.
Determine the moments of inertia and the product of inertia of the L3 x 2 x 1/4-14 angle cross section of Prob. 9.74 with respect to new centroidal axes obtained by rotating the x and y axes 30° clockwise.(Reference to Problem 9.75):Using the parallel-axis theorem, determine the product of inertia of the area shown with respect to the centroidal x and y axes.
From the given cross section determine the following: 1. Moment of Inertia with a. respect to the x axis. b. respect to the y axis. 2. Polar Moment of Inertia 3. Radius of gyration with a. respect to the x axis. b. respect to the y axis. 3. Moment of Inertia with respect to the neutral axis.