I only need help with part (d) of this engineering problem. A Carnot vapor power cycle operates with water as the working fluid. Saturated liquid enters the boiler at 1800 lbf/in.?, andsaturated vapor enters the turbine (state 1). The condenser pressure is 1.2 Ibf/in.? The mass flow rate of steam is 1x 107 Ib/h. Dataat key points in the cycle are provided in the accompanying table.Statep (Ibf/in.2)h (Btu/lb)11800115021.2735.51.247241800648.2 Determine:(a) the percent thermal efficiency.(b) the back work ratio.(c) the net power developed, in Btu/h.(d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.

A boiler is an external combustion system where the working fluid is heated with the aid of an…

Answered: Determine: (a) the percent thermal…

Determine: (a) the percent thermal efficiency. (b) the back work ratio. (c) the net power developed, in Btu/h. (d) the rate of heat transfer to the working fluid passing through the boiler, in Btu/h.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 4 a) A power plant based on the ideal Rankine cycle has a net power output of 10 MW.Superheated steam enters the turbine at 10 MPa, 500 (Degree)C. The condenser pressure is 15 kPa.Determine:i) the mass flow rate of the steam.ii) the rate of heat input to the cycle.iii) the thermal efficiency.
PLEASE ANSWER ALL AND SHOW COMPLETE SOLUTION. 1. Steam is the working fluid in an ideal Rankine cycle. The saturated vapor enters the turbine at 8.0 MPa and saturated liquid exits the condenser at a pressure of 0.008 MPa. The net power output of the cycle is 100 MW. Determine for the cycle (a) the thermal efficiency, (b) the mass flow rate of the steam, in kg/h, (c) the rate of heat transfer, into the working fluid as it passes through the boiler, in MW, (d) the rate of heat transfer, from the condensing steam as it passes through the condenser, in MW, (e) the mass flow rate of the condenser cooling water, in kg/ h, if cooling water enters the condenser at 15 DEGREE CELCIUS and exits at 35 DEGREE CELCIUS.
Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lbf/in2 and 1400°F. The condenser pressure is 2 lbf/in.2 The net power output of the cycle is 250 MW. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. (a) the mass flow rate of steam, in Ib/h. (b) the rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator. (c) the percent thermal efficiency. (d) the mass flow rate of cooling water, in Ib/h.
1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle?At 2.5 MPa: hg = 2803.1 kJ/kg sg = 6.2575 kJ/ kg – KAt 50 kPa: sf = 1.0910 sfg = 6.5029hf = 340.49 hfg = 2305.4vf = 0.0010300
Question 4 a) A power plant based on the ideal Rankine cycle has a net power output of 10 MW.Superheated steam enters the turbine at 10 MPa, 500 C. The condenser pressure is 15 kPa.Determine:i) the mass flow rate of the steam.ii) the rate of heat input to the cycle.iii) the thermal efficiency.
Steam at 4800 lbf/in.2, 1000 deg F enters the first stage of a supercritical reheat cycle including two turbine stages. The steam exiting the first-stage turbine at 600 lbf/in.2 is reheated at constant pressure to 1000 deg F. Each turbine stage and the pump have an isentropic efficiency of 85%. The condenser pressure is 1 lbf/in.2 If the net power output of the cycle is 100 MW, determine (a) the rate of heat transfer to the working fluid passing through the steam generator, in MW. (b) the rate of heat transfer from the working fluid passing through the condenser, in MW. (c) the cycle thermal efficiency.
A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 540 degree celsius, condenser pressureis 0.034 bar, mass flow rate of steam is 12 kg/sec. Draw the T-S and Schematic diagram of cycle and determine the following: d. The steam rates e. Heat rate of the cycle f. Pump Work g. Turbine Work
In a Rankine cycle steam enters the turbine at 2.5 MPa (enthalpies & entropies given) and condenser of 50 kPa (properties given), what is the thermal efficiency of the cycle? At 2.5 MPa: hg = 2803.1 kJ/kg; sg = 6.2575 At 50 kPa: sf = 1.0910; sfg = 6.5029; hf = 340.49; hfg = 2305.4; vf = 0.0010300
A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 540 degree celsius, condenser pressureis 0.034 bar, mass flow rate of steam is 12 kg/sec. Draw the T-S and Schematic diagram of cycle and determine the following: a. Ideal turbine work b. Ideal pump work c. Theoretical thermal efficiency d. The steam rates e. Heat rate of the cycle f. Pump Work g. Turbine Work
Question # 1 The networkoutput and the thermal efficiency for the Carnot and the simple ideal Rankine cycles with steam as the working fluid are to be calculated and compared. Steam enters the turbine in both cases at 5 MPa as a saturated vapor, and the condenser pressure is 50 kPa. In the Rankine cycle, the condenser exit state is saturated liquid and in the Carnot cycle, the boiler inlet state is saturated liquid. Draw the T-s diagrams for both cycles.
In a Rankine cycle steam enters the turbine at 2.5MPa (enthalpies and entropies given) and condenser of 50KPa (properties given), what is the thermal efficiency of the cycle? At 2.5MPa: hg = 2803.1 sg = 6.2575, At 50KPa: sf = 1.0910 sfg = 6.5029 hf = 340.49 hfg = 2305.4 vf = 0.0010300
Using T- diagrams , explain why superheating and reheating is necessary in a vapor power cycle from the functional perspective . Also show how it helps improve the efficiency of the cycle .