A 100mm* 40 mm* 20 mm steel block issubjected to a hydrostatic pressure of 10MPa.The Young's modulus and Poisson's ratio of thematerial are 150 GPa and 0.1 respectively.Determine change in volume of the block.

Given data, Steel block is subjected to a, hydrostatic pressure is=10 MPaYoung's modulus=150…

Answered: Determine change in volume of the…

Engineering

Civil Engineering

Determine change in volume of the block.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Related questions

Q: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, μ-0.038 N.s/m² from one tank to…

A: Given :

Q: Cite 3 possible advantages of the bidding process in Section 3. (Construction project) 2. What is…

A: Solution: Bidding on construction projects is defined as one of the important aspects of…

Q: FN=55 MN=62 SN= 71

A: Truss: Truss is a pin joint structure subjected to loading only on joint and there is only one force…

Q: A closed traverse has the following data: Line AB BC CD DA Length (m) Bearing 83.07 160.33 58.15…

Q: 1. Six beams with the cross section shown in the figure are made of different materials. Beam 1 is…

A: Size of # 9 bar is 1.128inch diameter. No of bars= 4 As(area of steel) = 4*π/4*1.1282 = 3.997 = 4…

Q: Determine the mass moment of inertia of the shaft about its longitudinal axis (in slugs - ft²).…

Q: The Reynold's number for the flow through smooth pipe is given by 105. The value of friction factor…

A: Given data- smooth pipeReynold's number Re=105To Find-The value of friction factor for smooth pipe f

Q: (d) Describe the methodology of finite element model of the cantilever beam using SolidWorks. (e)…

A: Experimental Results : Experimental results of natural frequencies are given in pre-measured dats of…

Q: UPVOTE WILL BE GIVEN! Write the solutions legibly. Answer in 2 decimal places. FUNDAMENTALS OF…

Q: What are the main reasons why construction industry is quite slow to accept changes in the work…

A: Q10 C Q11 C Q12 D

Q: Concrete is required for a column that will be Severe exposed to freezing and thawing. The cross…

Q: (a) What do values (each point) on Mohr's Circle represent? (b) Why is Mohr's Circle a useful tool?…

A: a. Representation and meaning of each point on the Mohr's circle-

Q: A mass of liquid being translated vertically downward with a uniform acceleration equal to the…

A: Given information in question Liquid having mass is accelerating vertically downwards To find out…

Q: UPVOTE WILL BE GIVEN! Write the solutions legibly. Answer in 2 decimal places. FUNDAMENTALS OF…

A: S = 3.6 m θ = 3°45' c = 0.3 m K = 100. TO determine: Horizontal distance between instrument and…

Q: The cantilever beam is subjected to a concentrated load of P = 40 kips. The cross-sectional…

A: Given values of the I beam, P= 40 kips bf= 5.51 in. tf= 0.332 in. tw= 0.356 in. d= 14.1 in. yH= 3.6…

Q: Is the modulus of volume compressibility (mv ) a constant? Explain with reference to a plot. Can…

A: The modulus of volume compressibility is used in soil to determine the rate of change in volume…

Q: Question: A rectangular column is shown in the figure, assuming fc'=28Mpa, fy=345Mpa, and e=110mm,…

A: Given:- The width of the rectangular column is 300 mm The compressive strength of the concrete =…

Q: Th speeds of 25 cars were observed. 10 cars were noted to travel at 38 kph, 8 cars at 39 kph, 2 cars…

Q: 25 INFL. LINE FOR RA VD, MA 'D' IS MID PT. BET. A 48.

Q: Determine the force in each member of the loaded truss as a result of the hanging weight W-130 lb.…

Q: A cylindrical tank is placed with its axis vertical and is provided with a circular orifice of 4 cm…

Q: 20 15 Head (cm) 10 5 0 5.0 cm 5.0 cm 1 2.0 cm T 5.0 cm + 2.5 cm 1.5 cm 2 a Ah = 5 cm ↓ 1 soil Datum…

Q: oedometer test on a normally consolidated soil reveal the normal consolidation line (NCL) from the…

Q: Question 3 Part a: For the section shown, determine the: • Maximum elastic Moment M • Fully plastic…

A: Given :

Q: A cantilever beam, 3 m long, carries a uniformly distributed load over the entire length. If the…

A: Given data- Cantilever beam span L=3 mUDL over entire spanslope θ at free end=1oTo Find-The…

Q: An electric motor M is used to reel in cable and hoist a bicycle into the ceiling space of a garage.…

A: Given Data: The motor can reel the cable at a steady rate of 16 in/sec. The lifting distance of the…

Q: 9m 6m 40KN A 120 KN 40KN hinged 6m 25m hinged B 25m с hinged Determine all the supports reactions of…

A: Find support reaction

Q: Q13. Q14. Q15. Which are the followings reflecting on requirement of sustainable/green procurement?…

A: The correct options for the questions are given below:

Q: a-37m b-50m c-53m C-230 kN-m F= 20 KN w-24 kNm Determine the support reactions at the left and…

Q: An exit sign is 16 ft (4.9 m) from an observer, and the smoke has the visibility listed here for 14…

Q: A hydraulic jump occurs in a trapezoidal channel with side slope of 1V:2H and base width of 3.8m if…

A: Given Data: The slope of the channel is 1V: 2H. The base width of the trapezoidal channel is b = 3.8…

Q: A sailboat moving in the direction shown is tacking to windward against a north wind. The log…

A: Wind Velocity: Wind Velocity is a fundamental atmospheric quantity. The air which is moving from…

Q: Q.2) Answer the following question. 1- The sieve analysis below was done for which type of…

A: The values in the table already calculated is incorrect and the correct values are given in the…

Q: at A can lift

Q: HYDRAULICS. Please answer ASAP. LIKE will be given! Answer in 3 decimal places.

Q: 4. Determine the displacement at point D. El is constant. Freed B Pinned 5 kN/m D

Q: Two identical plates of 63 mm wide and 3 mm thick is connected by a square pin with side dimension…

Q: Concrete is required for walls of a building that will be Moderately exposed to freezing and…

A: Given data:- Cross-section of a wall is 300×1500 mm Spacing between the reinforcing steel is 50 mm…

Q: The radius of the fillet is r = 3 [mm] and a reliability of 90% is desired. The shaft is made from…

A: Grooved Rotating Shaft M=150 Nm P=10 kN Torsional load between 50 - 130 Nm Radius, r=3 mm…

Q: A retaining wall has a height of 9m. It is subjected to uniformly distributed surcharge of 12kN/m2…

Q: The principal stress for machine component boiler are , 0.5 and 0. If yield stress is found 240MPa…

Q: Concrete is required for walls of a building that will be Severe Exposed to freezing and thawing.…

A: Reference : ACI 311 Mix design All tables are referred from ACI 311 Mix design. Table : Relationship…

Q: If f(x) = x(2x), then f'(x) is equal to: ○ 2 (2lnx + 1) © 2*(21n2 + x) © 2*(xln2 + 1) © 2*(In2 + 1)

A: Given: Question 1: f(x) = x (2x) , Find f'(x).

Q: Beginning Point P103 P104 P101 P102 Traverse Side Measurement and Calculation Table Ending Point…

A: Engineering surveying entails the planning and implementation of surveys for the engineering…

Q: PROBLEM 3: In DYN-002, a 20-pound sphere attached to a 4' cord at a 30-degree angle with the…

A: T= 57.3 lb N= 59.3 lb

Q: We require a mix with a mean 28-day compressive strength of 26.5 MPa) the size of the member and the…

A: Reference : ACI 318 Normal concrete ; No air entrained concrete. For 26.5 MPa ,By interpolation W/c…

Q: INFL. LINE FOR RA VD, MA 'D IS MID PT. BET. A 48.

A: We can solve it by using muller bresleu's principle To draw Influence Line Diagram (ILD) for…

Q: A culvert is designed for a flood frequency of 100 years and a useful life of 20 years. The risk…

A: Given data- flood frequency T=100 yearslife n=20 yearsTo Find-Risk involved in the design R

Q: The following are the results of direct shear tests performed on two identical samples of the soil.…

A: Using Mohr coulomb equation

Q: What will be the cant deficiency (cm), if maximum safe speed on a 5 Degree curve of a broad gauge…

A: Given- 5 degree curvebroad gaugespeed V=110 km/haverage speed=85 km/h

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

A 100mm* 40 mm* 20 mm steel block is
subjected to a hydrostatic pressure of 10MPa.
The Young's modulus and Poisson's ratio of the
material are 150 GPa and 0.1 respectively.
Determine change in volume of the block.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water in a hydraulic press, initially at 137kPa absolute, is subjected to a pressure of 280 kPa absolute. Using E=2.5GPa, determine the percentage decrease in the volume of water?
A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
A concrete dam retaining water is shown in the picture. If the specific weight of concrete is 23.5 kN/m3 , 2. Find the maximum intensity of pressure? 5. Find the resultant force? 7. Determine the minimum intensity of pressure?
(Bernoulli/continuity) Water flows steadily through the pipe shows in the figure below such that the pressures at sections (1) and (2) are 346 kPa and 107 kPa, respectively. Determine the diameter of the pipe at section (2), D2, if the velocity at section 1 is 21 m/s and viscous effects are negligible
1. A concrete dam retaining water is show in the figure. If the specific weight of concrete is 23.5 KN/m^3. What is the factor of safety against overturning? Find the location of the resultant. Find the maximum intensity pressure. Determine the minimum intensity pressure.
Water flowing along a horizontal pipe has a speed of 2.77 m/s and a pressure of 4.41 atm. Further along, the pipe narrows so that the cross-sectional area decreases by a factor of 6.62. What is the pressure in the narrow section?
2. What is the equivalent pressure head at the toe of the triangular dam in mm of Mercury? In meters of glycerine (s=1.35)?
Water at a temperature of 30°C flows through a concrete pipe with a diameter of 30 cm along a length of 500 m and has a flow rate of 0.03 m³/s. Calculate the pressure loss or drop in the pipe using a moody diagram. Also draw the friction factor on the moody diagram
A cylindrical tank 2m in diameter and 15 meters high is filled with liquid Z. A pressure gage at elev 10 m at the side of the tank reads 105 kPa. another gage at elev 6m reads 138 kPa. compute the (a) specific weight of the liquid and (b) density of the liquid.
A right circular cylindrical tank container, 2m in diameter and 4m high is 1/2 full of water. When rotated about its vertical axis at the rate of 60 rpm:A.) How many meters will the water surface drop at the center of the vessel? B.) What is the pressure, in kPa, at the base of the container along the perimeter? C.) What is the volume, in m^3, of the paraboloid formed by the rotation of the vessel? (Show complete solution)
A large, open cylindrical tank is 18.0 feet deep having a radius of 7.00 feet is layered with 6.00 feet of water (SG = 1.00) 8.00 feet of oil (SG = 0.650) and 4.00 feet of mercury (SG = 13.6). Compute the pressure (psi) at the bottom of each layer