Answer it with complete solution and explanation.Thank you! Module 1: Activity No. 2Exercises Problem on Resultant of Concurrent Force SystemName:Student No.Problem:Determine completely the resultant of the force system shown using the method ofcomponents. Use sketches and indicate clearly the angles.yT= 2500 Ibs30°45°Q = 400 lbs

T = 2500 lbs, 30o north of east Q = 400 lbs , 45o west of south

Answered: Determine completely the resultant of…

Determine completely the resultant of the force system shown using the method of components. Use sketches and indicate clearly the angles. y T= 2500 Ibs 30° 459 Q = 400 lbs

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter5: Displacement And Force In Two Dimensions

Section: Chapter Questions

Problem 104A

See similar textbooks

Related questions

Q: Determine the tension in the cable and the horizontal and vertical components of reaction of the pin…

A: Free body diagram

Q: Determine completely the resultant of the force system shown using the method of components. Use…

A: T = 2500 lbsQ = 400 lbsx component of T , Tx = Tcos 30°…

Q: 200 N 19. Draw the Horizontal and vertical component vectors of 200 N weight vector to the the…

Q: 180 N 180 N N 08T 310 N N 08T 310 N

Q: For the member that is shown below: 1. Determine the moment of the force 50N around point O. 2.…

Q: The uniform bar with end rollers weighs 85 lb and is supported by the horizontal and vertical…

Q: A spring of spring constant 40 N/m is compressed as shown. What is the magnitude and direction of…

A: Given, spring constant, k = 40 N/m compression, x = 0.500 m Spring force = kx , where k is spring…

Q: Four forces in a plane, act at a point O, the values and directions of the forces are being as shown…

Q: Determine the components of all forces acting on member ABCD of the assembly shown. Take P= 240 lb.…

Q: 5ks = 0.3 %3D

Q: Determine the resultant of the coplannar force system shown and locate it on a sketch of the system…

A: We first compute the resultant force in the coplanar system, Taking the upward forces as positive…

Q: Draw complete free-body diagrams for the bodies specified in the following problems. Neglect the…

A: Introduction: Free body diagram is the tool to identify the problem to specifying the direction of…

Q: for the five forces and a couple figure, find the resultant R" and locate it with- point o Shown in…

Q: from one end (see figure). There are pposite ends of the beam, where W, < W,. Find x such that the…

A: GivenW1=900 NW2=2700 N

Q: What is the difference between Center of gravity, center of mass and centroid of an object?

Q: An object with a triangular cross-section is free to rotate about the axis shown. Four forces with…

A: The correct option is Force 3

Q: Based on the diagram attached, determine and state the magnitude and direction of the net force…

A: Scenario - Forces are applied to different directions. Their resultant will be in accordance with…

Q: Two forces FA =175 lb and FB =205 lb are acting on the bracket shown with axes x,y,v and w…

Q: Find the resultant of the following forces using the polygon method. A = 30N at 45° B = 25N at 125°…

Q: Determine the equilibrant of the given vectors by (a) parallelogram method and (b) triangle method.…

Q: Replace the force system below with a single force and find its perpendicular distance to point O.…

A: Given: The Forces is given as, FA=10 lbsFB=50 lbsFC=80 lbsFD=50 lbs Sides of the rectangle is, a=5…

Q: Determine the resultant of the force system shown in fig. and its diarection if ?F1= 750 N and the…

Q: .i determine the resultant of the force system in next figure. And locate the resultant with respect…

A: Calculate the net force along the x axis: Rx=∑Fx=50 cos30°-100…

Q: A 145lb engineering student who is standing on beam EDF pulls vertically downward on a rope attached…

A: Write the equilibrium condition for the upper beam by taking the point B as equilibrium point.

Q: A rocket fires two of its engines. One engine produces a thrust of 800N in the forward direction and…

A: Given data: Thrust of first engine, F1=800 N Thrust of second engine, F2=500 N Angle, θ=50°

Q: A weight of 300.0 kg is pulled from the water by the setup consisting of two slanted poles and a…

Q: What force would balance (equilibrant) the resultant of the following vectors: 100 N, 45° north of…

A: Since you have posted a question with a multiple sub parts, we will solve first three sub - parts…

Q: Determine the resultant of the force system shown in fig. and its diarection if F1= 750 N ?and the…

A: The given forces can be represented in component forms as, Here, F1 and θ represent the force’s…

Q: The three forces shown is to be replaced by a single resultant force. Determine the distance d (in…

A: Given,

Q: Calculate the resultant of the forces shown in terms of magnitude and angles theta x, y, and z.…

A: Given

Q: Determine the magnitude and direction (to the nearest degree) of the equilibrant of the following…

Q: Resolve a force, F = 250 lb, into component vectors with directions indicated by the dashed lines…

Q: For the system forces showed, calculate the magnitude of the resulting force from the forces F, P,…

Q: The force system shown below has a resultant of 2OON pointing up along the Y- axis. Compute the…

Q: Resultant of Force Systems 6. The triangular block shown below is subjected to the loads P=1600lb…

A: Image-1

Q: If the rod shown has a weight of 150 N, calculate the magnitude of the reactions at A (horizontal…

A: Given data: The weight of rod is W=150 N. The length of rod is L=6 m. The angle made by rod is…

Q: QI) Determine the magnitude and direction of F, so that If the resultant of the three forces act on…

A: In this problem, the resultant force is 250 N and it makes an angle of 20o clockwise from positive…

Q: Determine the Resultant Force using the COMPONENT METHOD.

Q: Draw complete free-body diagrams for the bodies specified in the following problems. Neglect the…

A: The diving board’s f.b.d is as follows.

Q: shows an Atwood machine that consists of two blocks (of masses m1 and m2) tied together with a…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: ABC is an equilateral triangle. Las Lac=Lca=1.2 m. Find the resultant for the force system that is…

Q: Find the resultant of the two forces shown * ?in fig using cosine and sine laws

Q: How much upward force does the support 1 exert on the beam? Express your answer to two significant…

A: Free body diagram is shown as below: Mass of student = m = 86 kg Mass of beam = M = 96 kg For…

Q: Express the 2 forces in CVN then determine the resultant force in N generated at point A which is…

A: Given that: Coordinate of A (6,10,0) ft FAB=100 lbFAC=200 lb 1 lb= 4.448 N

Q: Using the method of components, find the resultant of the following concurrent forces. Note: After…

Q: Find the resultant of the following forces using the polygon method. A = 30N at 45° B= 25N at 125° C…

A: Using Polygon law of vector addition we draw the vectors as a polygon. Here,…

Q: An object weighing 350 N hangs from three ropes. If (theta)1 = 60 degree and (theta)2= 25.0 degree,…

Concept explainers

Special Relativity

The theory of special relativity discusses how space and time are related to objects traveling along a straight line at a constant speed. Simply stated, as an object reaches the speed of light, its mass becomes infinite and it is unable to move faster than light. This interstellar speed limit has been the topic of much debate in astronomy, and also in science fiction when people consider how to fly over large distances.

Question

Answer it with complete solution and explanation.

Thank you!

Module 1: Activity No. 2
Exercises Problem on Resultant of Concurrent Force System
Name:
Student No.
Problem:
Determine completely the resultant of the force system shown using the method of
components. Use sketches and indicate clearly the angles.
y
T= 2500 Ibs
30°
45°
Q = 400 lbs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

2. From the given set of system shown. a.) Which of the following gives the resultant of the force system. b.) Which of the following gives the angle that the resultant makes with the horizontal measured counter-clockwise c.) Which of the following gives the distance of the resultant from the intersection of x and y axes.
I need help with this problem: A. Calculate the magnitude of the total force. B. When the fourth force is applied to the mass, it is observed that the velocity of the mass stops changing and remains constant. What are the horizontal and vertical components of the fourth force? I've tried adding up all of the velocitys and found Vtotal = 111.8 N with a direction of 26.5 deg. Which is incorrect. Below is the graph we are given.
Could you please help with part b? i am unsure as to how to get the average force
What is the difference between 2D Force and 3D Force systems? Explain in no more than 50 words.
This answer (281.4) was not right. Can you try again? I've been doing this question for ahwile and cannot get it. Calculate the magnitude of the normal force on a 17.7 kg block in the following circumstances. (Enter your answers in N.) The block is on a level surface and a force of 165 N is exerted on it at an angle of 40.8° above the horizontal.
A block A is on a horizontal frictionless table. An ideal cord is tied to block A and is connected to a fixed hook hanging from the ceiling, passing through a pair of ideal pulleys, one of which is mobile and supports block B as shown in the figure. Use the coordinate system indicated in the figure to answer the following questions:- What is the ratio of the accelerations of blocks A and B? (Be careful with the signs of the reference system and set up the binding equation(s) correctly.) - What is the acceleration of block A in terms of mA and mC and say the cord tension
Resolve the vector components for the coplanar force system shown in Figure Q1a to calculate the magnitude of the resultant force and its angle of direction relative to the positive x-axis.
(Figure 1)Block 1, of mass m1, is connected over an ideal (massless and frictionless) pulley to block 2, of mass m2, as shown. Assume that the blocks accelerate as shown with an acceleration of magnitude a and that the coefficient of kinetic friction between block 2 and the plane is μ. Find the ratio of the masses m1/m2. Express your answer in terms of some or all of the variables a, μ, and θ, as well as the magnitude of the free-fall acceleration g.
Can you please answer this question. You can pick the diagram, calculations or explanations that make the most sense for kinetics and force. Thank you.
Answer only direction of the force (N, E, W, S, etc.) or provide diagram with x, y, z axis.
The "Giant Swing" at a county fair consists of a vertical central shaft with a number of horizontal arms attached at its upper end as shown in (Figure 1). Each arm supports a seat suspended from a 5.00-mm-long rod, the upper end of which is fastened to the arm at a point RRR = 1.80 mm from the central shaft. a)Make a free-body diagram of the seat, including the person in it. Draw the force vectors with their tails starting from the center of the dot. The location and orientation of your vectors will be graded. The exact length of your vectors will not be graded. b)Find the time of one revolution of the swing if the rod supporting the seat makes an angle of θθtheta = 32.0 ∘with the vertical.
Projectile Motion and Conservation of Energy Derive a set of equations that perdict the x-position where the ball hits the ground (y=0). This expression should depend only on the measured parameters shown in Figure 1 below: h1, h2, h3, D, L and value change h' 1. Find the magnitude of launching velocity v by using the conservation of total mechancial energy (incorporating the estimate of the energy lost to friction. 2. Find the horizontal velocity vx vertical velocity vy by referring to referring to the geometry of the final section of the track. 3. Find the time the ball is in the air t by considering the vertical motion involving vy and h2 alone. 4. Finally find the rang x Steps 3 and 4 may be combined by using the trajectory equation y(x) obtained by eliminating the time in equations for y(t) and x(t).