Determine if the following stress field is a valid solution of a plane elasticity problem assuming the body is isotropic, linearly elastic with small strains and with no body forces. o, =-6a,x² o„ = 12a,x , o, =12a,y²

Determine if the following stress field is a valid solution of a plane elasticity problem assuming the body is isotropic, linearly elastic with small strains and with no body forces. o, =-6a,x² o„ = 12a,x , o, =12a,y²

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.13P: Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v =...

See similar textbooks

Related questions

Q: Determine the principal stresses and the absolute maximum shear stress. 2.5 ksi 4 ksi 5 ksi

Q: For the plane stress problem, show that the neglected nonzero compatibility relations involving the…

A: Stress Variation in a body can be expressed by the equation of equilibrium. This equation can be…

Q: 3 1 4 If the components of stress at point p given by 1 2 -5 | Мра , 4-5 0 hen the stress vector…

A: Stress vector, σ=31412-54-50 Unit vector normal to the plane equation is, s=2x+y-z=1normal vector to…

Q: each graduation is 5 micron The maximum shear strain is:

Q: The state of stress in two-dimensionally stressed body at a point is as shown in Fig. Determine the…

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: The point A in the following plot represents: A or 0.5 -180 -90 90 180° -0.50, Graph of normal &…

Q: A 15 mm B 100 m 10 mm C

A: dia of brass rod AB = 15 mm dia of brass rod BC = 10 mm length of combined rod (AB + BC) = 100 mm…

Q: Transform the set of cartesian strain components (, = 400 µe (y = 250 µe „ = 125 pe %3D %3D 7ay =…

A: Solution:

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Mohr's Circle

Q: At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy=…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: shear stresses.(c) Angle of principal stresses (Op)(d) Angle of maximum shear stress (es) * o.y =…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: The strain components sx Ey, and yxy are given for a point in a body subjected to plane strain.…

Q: A steel shaft of diameter 50 mm and length 1.2 m (E = 210 GPa and v = 0.3) is loaded with multiple…

Q: The state of plane-stress at a point is given by o = 200 MPa, o, = 100 MPa and = 100 MPa. The…

A: It is very basic numerical of plane stress. Concept used is Maximum shear stress under biaxial…

Q: The strain components ɛ, Ey, and y,y are given for a point in a body subjected to plane strain.…

Q: at each of those points. Write each state of stress in the form of a tensor, observing the z-y-…

Q: Determine the vertical displacement of plate A due to shear deformations in the rubber. The…

A: Cross sectional area of shoe=(35mm X 25mm)Now,Shear stress on plate A,τ=(502)N(35mm X…

Q: 1. (a) If the displacement field is given by u kxy, u, = kxy, u, 2K(x + у)z where k is a constant…

A: u= ux= kxy v= uy= kxy w= uz= 2k(x+y)z Normal stress along X axis and X direction= εxx= du/dx= ky…

Q: 1 Jlgull -4 0 -4 4 0 Mpa ,then the stress vector has 0 8 If Oij unit normal vector n-1/V3(1,-1,-1)is…

A: Write the given data with suitable variables. σij=4-40-440008n^=13-13-13

Q: The three-dimensional state of stress at a point is given by 30 10 -10] [0]= 10 20 MN/m? %3D -10 20…

A: Given:

Q: Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C…

Q: Q3/ Using Mohr's circle find out the principle stresses and the maximum shear stress and the stress…

Q: The strain components E, Ey, and Vyare given for a point in a body subjected to plane strain. Using…

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain yy at P.…

Q: À rectangular steel plate (thickness 4mm) is subjected to a uniform biaxial stress field as shown in…

Q: Using transformation equations of plane stress, determine the normal and shear stress components for…

A: The clockwise angle between the x’-axis and the x-axis is, θ=0.5 rad×180°π=28.65° The stress…

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

Q: Determine the absolute maximum shear stress of the stress state acting on the element shown in the…

A: It is required to determine absolute maximum shear stress

Q: At point O of a part subjected to plane stress made of steel material (E = 210 GPa and v= 0.3) the…

Q: If the displacement field is given by Ux = kxy, uy = kxy, uz = 2k(x +y)z where k is a constant small…

A: Given Dataux=kxyuy=kxyuz=2kx+yzk-constant

Q: Transform the set of cartesian strain components , = 400 µe y = 250 µe 125 µe %3D 275 µe %3D Yy: =…

A: Solution:

Q: The square plate is such that L = 273 mm. The corners of the square plate are given the…

A: Shear strain is the change in angle between two rad surfaces at that point.

Q: Q1: If the stress tensor at appoint on a body is defined by: -8 6 -21 MPa [0] = 6 4 -2 2 -5…

Q: F(x,y) and G(x,y) are harmonic (i.e they satisfy the Laplace equation) show that the function…

Q: Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

A: As Given in case (1); σx= -60 N/mm2 , σy= -36 N/mm2 , ζxy= 5 N/mm2 So the principal stresses will be…

Q: The known stress components at a point in a body, relative to the (x, y, z) axes, are ox = 20MPA, Oy…

A: Given:-σx=20MPaσy=10Mpaτxy=30MPaτxz=-10MPaτyz=80MPaI2=-7800MPaTo find:-Stress component σz and…

Q: At a point in a stressed body, the known stresses are o, = 42 MPa (T), o, = 16 MPa (C), o, = 22 MPa…

A: Given, σx=42MPa(T)σy=16MPa(C)σz=22MPa(T)τxy=40MPaτyz=0τzx=27MPal=cos…

Q: The maximum principal stress in a material is 6 MPa. If the second invariant of the stress tensor is…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

Q: At a point on the flat surface of a member, load-stress relations give the following stress…

A: GIVEN: σxx=100 MPaσyy=0σzz=100 MPa τxy=20 MPaτxz=0τyz=20 MPa To find the principle stress σ2 and its…

Q: For the loading shown on the L-shaped part, determine the state of stress at points a, b, and c.…

Q: The stress tensor for a three-dimensional system for some x, y z axis system is 1. 30 20 -15] 30 MPa…

Q: The stress tensor in MPa for a three-dimensional system for some x, y z axis system is 20 40 -30 40…

A: Given Data:Stress tensor in MPa of a three-dimensional system 2040-30403025-3025-10 σx=20 MPa, σy=30…

Q: Determine the location of the shear center for the angle having equallegs, Fig.a. Also, find the…

A: sin 45=txx=tsin 45x=2×t sin 45=h2bh=2×b×sin 45h=2×b×12h=2×bh=2×b…

Q: direction in which the normal stress is zero, direction in which the normal stress is zero, ulate…

Q: Q3- a) Determine the shear strain yxy at corners D, (Y,), if the defamation is shown by the dashed…

A: Solution:

Q: Q1: If the stress tensor at appoint on a body is defined by: -8 6 -2] [0] =| 6 L-2 2 -5] 4 MPa…

A: Given: The state of stress is given below: [σ]=−86−2642−22−5

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

Correct and complete solution

Determine if the following stress field is a valid solution of a plane elasticity problem assuming the body is
isotropic, linearly elastic with small strains and with no body forces.
Ox = -6a,x?
O„ = 12a,x
, o =12a,y?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?