Answered: A thin rectangular plate is uniformly,…

A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain yy at P. Assume a = 17 in., b = 31 in., c = 0.19 in, %3D and d = 0.23 in. S b P a Answer:Yy = i prad.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.4P: An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy =...

See similar textbooks

Related questions

Q: A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain…

A: Given: The diameter of the pipe, d = 11 in The thickness of the pipe, t = 0.35 in The internal…

Q: 982. The strain components at a given point are x = -533 x 10, 6, = 67 x 10-6, and Y = -626 X 106.…

A: To find The stress components on the face whose normal is 45° from the X axis. Given The strain…

Q: 7.5-1 A rectangular steel plate with thickness 1 = 16 mm is subjected to uniform normal stresses o,…

A: The stresses in the plate can be calculated using the following equations- εx=σxE-μσyEεy=σyE-μσxE…

Q: The strain rosettes shown in Figures P13.50 were used to obtain normal strain data at a point on the…

Q: Problem E E V P13.50 -840 He -1,775 ue 665 ue 9,000 ksi 0.24

A: Given, εa = -840 μεεb = -1775 μεεc = 665 μεE = 9000 ksi v = 0.24 From figure, θa = 0°θb = 60°θc =…

Q: For part d, we introduce a wall at cross-section A. Determine the absolute maximum shear stress on…

Q: 10 ksi, o, = -4 ksi, and 29 x 103 ksi and poissons ratio is 0.3, determine the normal strain along…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: New Tab 15MDlxNzMz/a/NDCONZAWMTQYMTK3/details Open wi 3. A rigid member CBD is supported by a…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Answer:-

Q: The assembly shown consists of an aluminum shell (E, = 70 GPa, az= 23.6 × 10-6C) fully bonded to a…

Q: 10 ksi, oy -4 ksi, and o, = 8 ksi. Using E = The normal stresses at a point in a steel member are o,…

A: Answer: The normal strain along z is (0.2138 × 10-3) in/in.

Q: Question-2: A solid 20-mm-diameter shaft is subjected to an axial load P. The shaft is made of…

A: The lateral strain is the ratio of the wire's longitudinal diameter change to its lateral diameter…

Q: P I S8 X 18.4 Li L2 Using E= 33 x 106 psi, determine the strain energy due to bending for the steel…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Q: 40 60 A circle of 200 mm dia. is drawn on a mild steel plate before it is subjected to two mutually…

A: Given, d = Diameter of the circle = 200 mm σx= Normal stress in horizontal direction = 160 MPa σy=…

Q: A AISI 304 steel bar, 5 m long with square section (2x6 mm), is stretched by effect of a applied…

Q: 8- Following are the reading recorded at a point of structure tested by a 60° rosette: Ea =…

Q: A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress…

A: The strain values are given as, ε1=121×10-6ε2=304×10-6ε3=203×10-6 The Poisson's ratio is given…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

Q: The strain rosette shown was used to obtain normal strain data at a point on the free surface of a…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • ,…

A: Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: c = 790 mm, u = 1.3 mm, v = 5 mm The angles are α = 24o, and β = 66o It is required to…

Q: uniformly distributed stresses acting on the side faces plate are b = 10 in. t = 0.75 in.., E =…

A: Given data Width (b) = 690mm = 69*10-³m Thickness (t) = 40mm = 40*10-³m E = 41 Gpa = 41*10⁹ V =…

Q: Define the terms shear stress and shear strain, illustrating your answer by means of a simple…

A: given data: shear load=30KN=30000N shear stress of brass not exceed(σb)=50MN/m2=50MPa=50N/mm2 shear…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given data: u=1.4 mm v=5.1 mm c=680 mm α=21o β=69o

Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…

Q: The coordinates of arectangular lamine ABCD before deformation are: (0,0), (0,100), (150,100),…

A: The give rectangular Lamine ABCD is,

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: Consider the state of plain “stress" for the following element. Derive the parametric value for the…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: c = 720 mm u = 1.7 mm v = 3.5 mm α = 31o and β = 590 It is required to determine the…

Q: Figure 1. The boiler has an inside diameter of 1800 mm and a wall thickness of 20 mm, and it is made…

Q: Q4) In fatigue test, the specimen constructed as in figure, which its broken at 50118 revolution.…

Q: A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume…

A: Given data: a=1350 mmb=850 mmc=1 mmd=1 mm Need to determine the shear strain.

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: u = 2.0 mm v = 4.2 mm c = 775 mm α = 20o, β = 70o It is required to determine the strain…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Please refer to the detailed solution given below, Answer - Shear strain is 4696.37 Micro-Radian

Q: xy = 210 MPa Using the Maximum Shear

A: Given Data⇒ Steel bar σx= 194 MPa σy= 100 MPaζxy= 210 MPa Maximum Shear Stress Theory

Q: B 60 5 in. 8 in. A P 6. Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC…

Q: 3. A long thin walled cylindrical shell, closed at both the ends, is subjected to an internal…

A: Let us consider, Diameter of cylindrical shell = d Thickness of cylindrical shell = t Pressure…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in…

Question

A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain yy at P. Assume a = 17 in., b = 31 in., c = 0.19 in,
%3D
and d = 0.23 in.
S
b
P
a
Answer:Yy =
i
prad.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
Solve the preceding problem if the plate is made of aluminum with E = 72 GPa and Poisson’s ratio v = 0.33. The plate is loaded in biaxial stress with normal stress sx= 79 MPa, angle Ø = 18°, and the strain measured by the gage is e = 925 × 10-6.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A rubber sheet in biaxial stress is subjected to tensile stresses ax= 270 Pa ander,. = 144 Pa. The corresponding strains in the sheet are e. = 0.0002 and = 0.000015. Determine Poisson’s ratio and the modulus elasticity of the material.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.