Determine minimum and maximum input voltages required for proper regulation to be performed by a Zener diode when connected across a variable input voltage. Assume Izk = 1.0mA, Izm = 120mA, Vz = 10V and series current limiting resistor Rs = 5602. Draw circuit diagram and plot graph for reverse V-I characteristic and label proper values on graph.

Determine minimum and maximum input voltages required for proper regulation to be performed by a Zener diode when connected across a variable input voltage. Assume Izk = 1.0mA, Izm = 120mA, Vz = 10V and series current limiting resistor Rs = 5602. Draw circuit diagram and plot graph for reverse V-I characteristic and label proper values on graph.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Sketch the I-V characteristic curve for a real diode and label the main parameters and regions.
In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
As shown is a positive parallel clipper circuit which has an input voltage of E=t5V. The negative output voltage is to be -4.5V when lo is 5mA. Assume ideal diode model approximation. Determine the value of R1 in ohms. Note: Write only the numeric value of the answer, round to 4 decimal places. No need to include the unit. R, +E ww Output Input D, -E -(E-1,R,)
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Determine the voltage across the diode in the figure below, using the complete diode model with: r'd = 10-? and r'R = 100-M?a. The value of the forward current. (in Amperes)b. The value of the forward voltage. c. The value of the voltage across the diode.
Determine the voltage across the diode in the figure below, using the complete diode model with: r'd = 10-? and r'R = 100-M? a. The value of the forward current. (in Amperes) b. The value of the forward voltage. c. The value of the voltage across the diode.
Determine the value of RL that will establish maximum power conditions for the Zener diode.