Answered: Determine real and reactive power…

Determine real and reactive power associated with each element in the following circuit. -352 Ht 202 8 jlon GO 238 v 420°

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Related questions

Q: Solve for the following requirements Load Voltages Line Currents Source Complex Power

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: R1 R2 ZL 100/0 Vx 0,8Vx

A: Maximum average power delivered to load

Q: For the circuit shown below, determine the real, reactive and apparent power for each element…

A: Write KVL equation for the circuit given and solve for current I; 2402∠60°-I5+8j-2802∠30°=0…

Q: 20. A 250V, 60 Hz supply inductive-capacitive circuit with Xe = 38.52 consumes 1600W. i) If the…

A: V = 250 V F =60Hz

Q: For the circuit with source V1 shown below, determine the average power supplied by V1: v1(t) = 15…

Q: 1. Calculate the current in J3 ohm inductor; compute the power of J3 ohm. Use Nodal analysis - j22…

Q: For the network of the figure below, Calculate the true power delivered to the reactance Xc. R 20 E…

Q: Voltage Supply, VL = 450 V Frequency, Felec. = 50 Hz Resistance, R = 352 per phase Inductance, L =…

A: It is given that: VL=450 VR=35 Ω/phL=0.55 H/phfelec=50 Hz

Q: 2 kohms (1) 70 nF 13 H Load #3 Find the average power and the reactive power absorbed by the load in…

A: In this question, Find the average power and reactive power of the circuit. We know complex power…

Q: 2. An impedance of 4-j3 ohms is connected in parallel with an ideal inductor L across a 110V, 60hz…

A: We need to find out value of inductance for given condition in the given circuit

Q: A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158…

Q: A load consists of R=78 Q, XL=71 Q and Xc=47 Q. All the elements are connected in parallel across…

Q: . For the circuit shown in figure below, determine the current flowing at impedance (4+j3) Q 132 15…

A: KVL states that algebraic sum of voltage in a closed loop must be equal to zero. It is also called…

Q: Figure 2 3) As referred to Figure 2, determine these quantities: a) Average power, P delivered by…

Q: ww C R www is 7.5 mH 12 Q2 Z ?For the circuit shown above, what is the maximum average power that…

Q: Compute for the following and draw the power triangle a. Real power b. Reactive power c. Apparent…

Q: In a circuit having pf = 0.85 which is connected to 240V, 60Hz supply. If the load consume a power…

A: Given, Power factor = 0.85 Supply voltage (Vs) =240 V Frequency (f) =60 Hz Load consumes real…

Q: Given the circuit below, determine a) the overall power factor, b)the real power dissipated, c.) the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: If, for the Figure below, E = 240 Z0° V, a = 0.5, and Iz = 2L20° A, determine the following: IL Eg…

Q: 2. Find the value of reactive power in the system which draws a 10-A current having a power factor…

A: It is given that: I=10 Acosϕ=0.8 laggingV=250 V

Q: 6. A load absorbs maximum power from the circuit shown below. Calculate the load impedance and the…

A: The given circuit Supply current will

Q: R1 R2 Vx 100/0 v 0,8Vx +1

A: Given

Q: (ii) A string of suspension insulators consists of three units if the voltage acros the line unit is…

A: Bartleby has policy to solve only first 3 subparts of a question. For rest subparts re-upload them.

Q: Show your solution for this problem. A 400V, 3-phase star connected alternator supplies a…

Q: POWER ANALYSIS IN CIRCUITS find, the complex power absorbed in: a. 1 ohm b. capacitor -j10 ohm…

Q: Compute the power factor and the reactive factor for the networkinside the box , whose voltage and…

A: The power factor is the ratio of the active power consumed to that of the apparent power consumed…

Q: Calculate the average power and the reactive power at the terminals ofthe network shown if V=100 15°…

A: given: V=100∠15° V I=4∠-105° A average power P=VIcosϕP=100×4×cos120°P=-200 W

Q: 1 Ohm 2 Ohms Ohms 4 Ohms ELECTONICS H 220V H Ohms

A: Brief description: In the above given question they have mentioned an electrical circuit which is…

Q: 9. The power factor of a load on a 120 volt. 60HZ source is raised from 0.707 to 0.866 lagging by…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 4. Calculate the real or reactive power delivered to each passive element. Also, determine the real…

A: Given

Q: In the power triangle of figures below, calculate the missing parameters; the reactive power (Q),…

Q: Use wye-delta/delta-wye transformation to determine the value of current i and equivalent resistance…

A: In this question, We need to determine the current i and equivalent resistance? We are solving…

Q: 4A

A: First we will do source transformation then we will find voltage by voltage divider rule.

Q: Problem 3 Use the definition of complex power to calculate the real and reactive power for the load…

A: Given circuit shown Vs=110∠0° vRs=4 ΩRL=10 ΩjXL=j6 Ω

Q: Determine the complex power for the following cases: (a) P = 269 W, Q = 150 VAR (capacitive) (b) Q =…

A: (a) Given values are - P=269WQ=150VAR (capacitive)

Q: Q1 (a) Based on the circuit in Figure Q1(a); (i) Calculate the total appearance power, real,…

Q: The reactance of the Impedance Z=100 261 ° is: O 100 Ohms 48.48 Ohms 87.46 Ohms 1.64 Ohms

Q: The reactance of the Impedance Z=1 O 100 Ohms 48.48 Ohms 87.46 Ohms 1.64 Ohms

Q: A load consists of R=78 Q, XL=71 Q and Xc=47 Q. All the elements are connected in parallel across…

A: Given, a load consist of R= 78 ohm XL= 71 ohm XC= 47 ohm All elements are connected in parallel…

Q: C is 7.5 mH 12 Q2 ?For the circuit shown above, what is the maximum average power that can be…

A: In this question we need to find a maximum average power transfer to load.

Q: Q20. A 250V, 60 Hz supply inductive-capacitive circuit with Xe 38.52 consumes 1600W i) If the…

A: Frequency f 60Hz Voltage v =250V

Q: 1. A resistance of 20 W and a coil of inductance 31.8 mH and negligible resistance are connected in…

A: The solution is given below

Q: The admittance of a network is (0.05– j0.08) S. Determine the values of resistance and reactance in…

Q: A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158…

Q: A series resistance-capacitance (R-C) circuit is connected to a 230 volt 60 cycle source. If the…

A: When R and C are connected in the circuit then Resistance is only responsible for the active power…

Q: Find the power delivered to an element whose current is given as i = 5 cos 60at A and voltage at v =…

Q: 16. Find the value of impedance which absorbs a complex power of 2300 VA with a 30 degrees angle at…

Q: Determine the equivalent impedance in the circuit v, (1) = 7 cos (3,000r + ) V Rị = 2.3 kN R2 = 1.1…

A: Impedance: It is a measure of the overall opposition of AC current in the circuit and it is…

Question

Solve the question in the image

10.
Determine real and reactive power associated with each element in the
following circuit.
-352
Ht
202
jron
60 130 v

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the instantaneous source voltage. Also determine the phasor and instantaneous currents entering the positive terminal if the circuit element is (b) a 20 resistor. (C) a 10mH inductor, and (d) a capacitor with 25 reactance.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
What is the total apparent, reactive, and real power of the system? Also, determine the power factor.
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
Three Impedances each of (11 – j20)Ω are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from the supply. Also, draw the Phasor diagram for the mesh connection and mark the Line current, phase current line voltage, and phase angle between phase current and phase voltage. phase current (Ip) = Line current = real power= reactive power=
Given a tee connected system with power factor of 80 percent and true power of 2,500 kW. Calculate the reactive power.
Determine the complex power delivered by the source to the circuit below