Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 6.12 0+020 8.78 0+040 8.95 0+060 8.19 0+080 5.46 0+100 5.01 Use the best method applicable. Round your answer to 3 decimal places.

Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 6.12 0+020 8.78 0+040 8.95 0+060 8.19 0+080 5.46 0+100 5.01 Use the best method applicable. Round your answer to 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia.) cut into the…

Q: An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from…

Q: A baggage with a weight of 40 pounds cascades down the smooth incline with total distance of 20 feet…

Q: A horizontal platform with a diameter of 6 m revolves about its center of 20 rpm. Find the…

Q: The Bar shown is subjected to a tensile load of 150 kN. If the stress in the middle portion is…

A: Given: The tensile load is 150 kN. The stress in the middle portion is 160 N/mm2. The total…

Q: 1. A member is formed by connecting a steel bar to an aluminum bar is shown. Assuming that the bars…

Q: Design an I-section purlin, for an industrial building situated in the outskirts of Allahabad, to…

Q: Determine the maximum reaction at support B, the maximum shear at point C and the maximum positive…

Q: to determine: a.) head loss from A to B b.) Q1 and Q2

Q: The beam shown in the figure is supported at roller A and pinned at B and has a uniformly…

A: The algebraic sum of the vertical forces at any section of a beam to the right or left of the…

Q: Determine the bending stress along the x-axis of the W section. Determine the bending stress along…

Q: A cylindrical sample of soil having a cohesion of 80 kN/m2 and an angle of internal friction of…

Q: Determine (a) the maximum bending stress, (b) the maximum shearing stress due to V in the simply…

Q: saturated specimen of cohesionless sand was tested under drained conditions in a triaxial…

Q: For a normally consolidated insensitive clay angle of friction_CD = 30°. Deviator stress at failure…

Q: A B C mmmmm MI "a" 5.0m "b" D 3.0m E "2" F

Q: For a normally consolidated insensitive clay 0_CD= 30°. Deviator stress at failure of the same soil…

Q: Given the data of a continuous solid one-way slab. Spans given are all clear spans. For shear and…

Q: A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal…

Q: A L = 1500m D = 750mm Q = 1.2 m3/s ELEV. = ?? C D L = 1800m D = 450mm A three reservoir problem…

Q: drained

Q: Subject: Soil Mechanics Please provide a solution and diagram In a consolidation test the following…

Q: Determine the magnitude of the tension at support A (N). Supports are pin connected

Q: Boreholes reveal that a thin layer of alluvial silt exists at a depth of 50 ft below the surface of…

A: shearing resistance = b. 2449

Q: Oil is flowing upward through a Venturi meter as shown. Assuming discharge coefficient of 0.984,…

Q: A cyclist on a circular track of radius r = 800 feet is traveling at 27 ft s^-1. His speed in the…

Q: 1. EXAMPLE 11.2 Calculate the station of the BC and EC. You are given the following information:…

A: Deflection angle, ∆=12°51'Radius of curve, R=400mThe station of point of intersection, PI=0+241.782

Q: For a given consolidated clay: Gs= 2.71; LL= 45; In situ average effective overburden pressure = 120…

A: Solution: Given: Consolidated clay Gs = 2.71 LL = 45 Po = 120 kPa eo = 0.80 H = 4 m Effective…

Q: A clay stratum is 4.5 m thick and rests on a rock surface. The coefficient of consolidation of a…

Q: Q4) Water flows through a contraction section as shown. A pressure gage connected between the…

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m -1.5 m

A: Given - simply supported beam of 3m with concentrated moment of 5Kn-m at one end. to find - slope at…

Q: A certain roadway designed to have a speed limit of 50mph. If the superelevation is 12 and the…

Q: The I-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

Q: A normally consolidated soil was subjected to tri-axial test with the following data: cell pressure=…

Q: is desired to obtain information about the in-situ strength properties cohesion and angle of…

Q: PROBLEM # 1: Use the Method of Sections The two beams shown are connected by an internal hinge at C…

A: Given data:

Q: V₂ voids solids W = 18% Ys= 170 lbf/ft³

Q: The following data are from a direct shear test on an undisturbed soil sample. Represent the data by…

Q: Problem. Draw the shear and moment diagram of the beam loaded as shown in Fig 60 KN 30 kN 2m R₂ R₁…

A: The length of beam, l=7mThe support reactions are R1A support & R2B supportThe loads applied ar…

Q: is desired to obtain information about the in-situ strength properties cohesion and angle of…

Q: 4. A force of 540N is directed from C towards E in the cube. a. Determine the moment about the…

Q: A grain size analysis is performed on 3500 g of dry sand. No soil is retained on the 12.5-mm opening…

Q: Example 9.5 Calculate the area of the underground roadway from the measurements given. Assume the…

Q: The steel tie-bar shown in the figure has been designed to carry a tension force of 76 kN when…

Q: The circular shaft AB consists of a 24.2 mm diameter solid steel cylinder in which a 11.4 mm…

A: Ans: 53 N.m

Q: and the bed ch elevation 92 m.

Q: 1. The Block shown are connected by flexible inextensible cord passing over frictionless. pulleys.…

Q: As shown in the figure, where is the location of moment equal to zero from point A in lb-ft? Use 2…

Q: The 1-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

Concept explainers

Boundary Surveys

A boundary survey is a property survey used to measure the perimeter of any property to locate the boundary line. Only after deciding the boundary, the area of a property can be computed. Bases on the area, the land can be subdivided, sold or any building can be constructed on the land. The property corners are first marked with any type of markers, such as rebar, metal survey markers, pipe, or wooden flags, and are then labeled for identification. The markers should be visible from all sides of the property to ensure optimum visibility. Any paint that assures visibility is used to indicate the boundaries in between the corner points. The procedure of delineating property lines must adhere to legal description and guidelines and it is an important part of the land registration system. This type of surveying is also called cadastral surveying.

Question

Determine the area bounded by a straight road and an irregular boundary using the data given below:
STATION
OFFSETS
0+000
6.12
0+020
8.78
0+040
8.95
0+060
8.19
0+080
5.46
0+10
.01
Use the best method applicable.
Round your answer to 3 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 8 0+020 6.25 0+040 8.43 0+060 6.75 0+080 8.28 0+100 5.86 Use the best method applicable. Round your answer to 3 decimal places.
From a transit line to the edge of a river, a series of perpendicular offsets are taken. These offsets are spaced 4.50 meters apart and measured in the following order: 0.50, 1.50, 2.50, 5.50, 8.50, 7.50, 3.50, 5.50, and 2.50m . By Simpson's Third rule, compute the area, express as whole number.
A surveyor sets up a transit at X which is located at the middle portion of a four sided tract of land and reads directions and measures distances as given in the table. Line Azimuth (°) Distance (m) XA 72 432.42 XB 150 524.46 XC 214 483.08 XD 319 565.07 Find the area (m2) of the land.
Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 5.74 0+020 4.85 0+040 8.69 0+060 7.82 0+080 7.59 0+100 6.44 Use the best method applicable.
For the rectangular lot, observations of sides A and Bwith their 95% errors are (252.46, {0.053) and (605.08, {0.072) ft, respectively. Calculate the parcel area and the estimated error in the area.
A 50 m tape was used to measure a square lot that was 0.05 m too short. If the area of the lot is 5000 m², what is the error in the computed area? a. 11.005 m² b. 10.015 m² c. 9.004 m² d. 12.003 m²
A rectangular lot was being measured using a 30-m metallic tape which was 6 mm too long. The recorded dimension where 70.50 m long by 37.10 m wide. What is the error in area (m^2) introduced due to the erroneous length of tape? A. 1.05 C. 0.86 B. 1.86 D. 2.02 It is required to lay out an exact distance of 100 m using 50 m tape that's 0.02 m too long. Compute the distance measured with the tape to make the points the proposed distance apart. A. 99.96 m C. 99.98 m B. 100.04 m D. 100.02 m ps. with solution, please.
How did you get 61.818, 19.303, -1.303 , 5.697 and15.697??
Question: Determine the subdivided areas by a line passing through corner C and at the mid-length of the line EA. Line Distance (m) Bearing Latitude Departure AB 145.26 N 28o45’W BC 80.42 N 33o00’ E CD 82.71 S 88o30’ E DE 90.38 S 30o 28’ E EA 153.81 S 41o 46’ W Solution:
A. 31.468"B. 7.234"C. 17"D. 24.234"
What is the area of a rectangular field and its estimated error for the following recorded values: 243.89 +-0.05 ft, by 208.65 +-0.04 ft.
Why did you use 4000 when checking here 107170 > 4000?