Answered: Determine the axial force required to…

Determine the axial force required to engage a cone clutch transmitting 25 kW power at 750 rpm. Average friction diameter of the cone is 400 mm, semicone angle 10°and coefficient of friction 0.25.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.77P: The cone clutch transmits the torque C through a conical friction surface with cone angle . The...

See similar textbooks

Related questions

Q: An automobile single-plate clutch consists of a pair of contacting surfaces. The inner and outer…

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone…

A: For answer refer the next page.

Q: (b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: Friction Clutches : Friction clutches are mechanical devices which are used to transmit power from…

Q: Q) The shaft of a collar thrust bearing rotates at 200 r.p.m and carries an end thrust of 10 tonnes.…

A: The answer is in next step

Q: A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of…

Q: A double threaded right-handed worm gear transmits 15 hp at 1150 rpm. The pitch of the worm is 0.75…

A: Given data Power = 15 HP N = 1150 rpm p = 0.75 in; m = 1/p = 1.33 mm = 2 D1= 3 in = 76.2 mm z1 = 38

Q: A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial force…

Q: ..A cone clutch with a cone angle of 15° transmits 58 kW at 1300 rpm. The coefficient of friction of…

A: Givenθ=15oP=58kWN=1300 rpmμ=0.11Dm=250mm=0.250m

Q: single plate clutch, effective on both sides, is required to transmit 20 kW at 2500 rpm. Determine…

A: Clutch : It is a device used in transmission of power. The clutch is used to engage & disengage…

Q: A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a…

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

Q: A single plate cutch consists of one pair of contacting surfaces. The inner and outer diameters of…

A: Given Data Inner diameter of clutch is: di=100 mm=ri=50 mm Outer diameter of clutch is: do=150…

Q: In an engine governor of the Porter type, the upper and lower arms are 200mm and 250 mm respectively…

A: The options given are wrong as no option matches.

Q: A double square thread power screw has a pitch of 6 mm and mean radius of 34 mm. If it is used to…

Q: shown below. The coefficient of friction for the screw is f = 0.06 and friction du negligible f≈ 0.…

Q: A single-plate clutch has a friction disc with inner and outer radii of 20 mm and 40 mm,…

A: Uniform pressure theory is when the product of pressure and area of the contacting surface…

Q: An engine running at 1100 rpm drives a line shaft by means of a belt. The engine pulley has a 9 in.…

A: Belt drives are a sort of frictional drive that transmits power from one shaft to the next. a system…

Q: The nominal diameter of a triple- threaded square screw is 50 mm, while the pitch is 8 mm. It is…

A: (i) To find : The torque required to raise the load. Given : The nominal diameter of screw is d=50…

Q: termine the size of the clutch plate suitable for an Ambassador car employing a single plate type…

A: we will use uniform pressure theory

Q: A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: A band brake having band-width of 80 mm, drum diameter of 250 mm, coefficient of friction of 0.25…

A: From the given data, useful data can be given by, Drum diameter = d = 250 mm = 0.25 m Coefficient of…

Q: A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included…

A: The maximum force (tension) in the belt can be given as - T1 = 3×Centrifugal force500 =…

Q: AN ENGINE DEVELOPING 45 KW AT 1000 R.P.M IS FITTED WITH A CONE CLUTCH BUILT INSIDE THE FLYWHEEL. THE…

A: The answer is in next step

Q: An open belt drive running at 2.5 m/s transmits 25 kW. The angle of lap on the smaller pulley is…

Q: In an engine governor of the Porter type, the upper and lower arms are 200 mm and 250 mm…

Q: Q2/ A dry single plate clutch is to be designed for an automotive vehicle whose engine is rated to…

Q: A triple-thread Acme-form power screw of 50 mm major diameter is used. The nut makes 1.5 turn per cm…

Q: ider keyed to .A centrifugal clutch has four shoes which slide each spring is 50 N/mm and the…

A: Given: n=4rc=5 mm=0.005 mP=500 Nr=160 mm = 0.16 mDi=400 mm=0.4 mmshoe=8 kgk=50N/mmμ=0.3N=500rpm

Q: A centrifugal clutch is to be designed to transmit 15 kW at 900 r.p.m. The shoes are four in number.…

Q: A multi disc clutch has five plates having four pairs of active friction surfaces. If the intensity…

Q: An automobile single plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform pressure theory: When the clutch and bearing mating components are fresh, the contact…

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: First, draw the free-body diagram of the handle: Now write the momentum equation about the point O.…

Q: A single plate clutch consists of a pair of contacting surfaces. The inner and outer diameters of…

A: When clutches are new i.e., thickness of the clutch lining is also same in new clutch. So, a uniform…

Q: A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are…

A: Given data: Power, P = 89.52 kW N = 3000 rpm Coefficient of friction, µ = 0.08 Axial pressure, Pav =…

Q: A lifting mechanism as shown has two single-lead 3/4“ diameter ACME thread screws. The thread…

A: Given Information: The diameter of the screws (d) = 3/4 inches The coefficient of friction (µ) =…

Q: A single plate clutch, effective on both sides, is required to transmit 75 kW at 1000 rpm. Determine…

Q: :An open belt drive with (200 and 150 mm) pulleys diameters, and the central distance equal to (0.5…

Q: An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a…

Q: mm diameter and a drive pulley of 200 mm diameter, whose centres are 1000 mm apart. The driving…

Q: Q2/ A conical clutch an included angle of 60º. the outer radius and inner diameters are 80 and 20 cm…

A: Given data, Since, the clutch is of two halves. So, the cone angle of the clutch is α=602α=30° Outer…

Q: A pullev 615 mm in diameter transmits 40 kW at 630 rpm The arc of contact between the belt and the…

Q: A single trapezoidal metric thread power screw is to raise a load of 60 kN. The screw has a mean…

Q: Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner…

Q: A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is…

A: To find: The power transmitted by the drive. Given: The speed reduction ratio is D:d=6:1. Here, D…

Q: A flat belt passes over two idler pulleys and under a rotating drum of diameter 8 in. The axle of…

A: Given, diameter of pully (d) = 8 inchTorque on the drum = 30 lb ftCoeff of static friction between…

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power…

A: Clutches are defined as the machine element which is used to engage or disengage driver and the…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Determine the axial force required to engage a cone clutch
transmitting 25 kW power at 750 rpm. Average friction
diameter of the cone is 400 mm, semicone angle 10°and
coefficient of friction 0.25.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the mean diameter is to be 355mm. The coefficient of friction between the contacting surfaces is 0.20 and the maximum normal pressure is 83 kPa, determine the outside diameter of the clutch. a. 384.3 mm b. 356.2 mm c. 349.5 mm d. 339.2 mm
An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two square-thread lead screws, 1.5 inches in (major) diameter, are used for this application. Determine the torque required to raise this lift if the moving part of the elevator weighs 800 pounds and the coefficient of friction is assumed to be 0.15. For the elevator described, find the efficiency and power required if each lead screw is driven at 175 rpm. Verify if this is self locking.
Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at 500 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 13.5o and a maximum mean diameter of 300 mm. The coefficient of friction is 0.25. The normal pressure on the clutch face is not to exceed 0.1 N/mm2
A single plate clutch, effective on both sides, is required to transmit 75 kW at 1000 rpm. Determine the outer radii of frictional surface when the ratio of radii is 1.75 and the maximum pressure is not to exceed 0.5 MPa. Also determine the axial thrust to be provided by springs. The mean radius of the frictional surface for uniform wear is 110 mm.
A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of linings is 0.16. Determine the axial spring force necessary to engage the clutch in N if the mean diameter of the active conical sections is 250 mm.
The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an inner diameter of 250 mm. The average value of the coefficient of friction is 0.25, and the operating force is 5 kN. Find the torque capacity when the clutch is new, the maximum pressure and the torque capacity after a sufficiently long operating period.
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
A centrifugal clutch is to be designed to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at which the engagement begins is 3/4th of the running speed. The inside radius of the pulley rim is 150 mm. The coefficient of friction may be taken as 0.25. Determine: 1. mass of the shoes, and 2. size of the shoes.