Determine the Coefficient of Performance (COP) of the reversible cycle shown in the sketch (T in Rankine). Use the differential form relating heat transfer, temperature and entropy and do some basic integrals to get your Q values to use in COP calculation. 1000 500 0.1 0.4 S (Btu/R) T(R)

Determine the Coefficient of Performance (COP) of the reversible cycle shown in the sketch (T in Rankine). Use the differential form relating heat transfer, temperature and entropy and do some basic integrals to get your Q values to use in COP calculation. 1000 500 0.1 0.4 S (Btu/R) T(R)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the following quantities for a reversible Carnot cycle: Step 1 q = 850 J, w = -434 J Step 2 q = 0 , w = -115 J Step 3 w = 72 J Step 4 q = 0, w = +115 J a) Calculate the efficiency of the cycle. b) If the initial temperature in step 1 is 25°C, what is the temperature at the end of step 2. c) If the number of moles of ideal gas involved in the cycle is 0.1 mol; calculate ΔH for step 4
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor, delivering a net power of 1 MW to the propeller. Air enters the diffuser at 8000 m altitude (Ta = 236K, pa = 36 kPa) with a velocity of 550 km/h, and decelerates essentially to zero velocity. The compressor pressure ratio is 5.3 and the compressor has an isentropic efficiency of 83%. The turbine inlet temperature is 1360 K, and its isentropic efficiency is 86%. The turbine exit pressure is 10 kPa higher than the ambient pressure at that altitude. Flow through the diffuser and nozzle is isentropic. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Using an air-standard analysis, determine: a) The mass and volumetric flow rates entering the diffuser, in kg/s and m3/s, respectively.b) The rate of heat addition to the combustor, in MW.c) The velocity at the nozzle exit, in m/s.
A Carnot cycle has a thermal efficiency of 32%. If the reject heat is 750 KJ at 500°C, determine the change in entropy
Write legibly, provide manual step by step solution, and diagram for below given problem. A throttling calorimeter is connected to the superheated steam line supplying steam to the auxiliary feed pump on a ship. The line pressure measures 2.5 Mpa. The calorimeter pressure is 110 kpa and 150 deg C. Determine the entropy of the steam line. a. 6.8 KJ/kg-deg K c. 6.6 KJ/kg-deg Kb. 6.2 KJ/kg-deg K d. 7.5KJ/kg-deg K
Show that all reversible engines operating between the same two reservoirs have the same efficiency
Describe and explain the Carnot cycle. Provide illustration to assist your explanation.
COMPLETE SOLUTION. FINAL ANSWER ARE IN ENGLISG SYSTEMS. DRAW A DIAGRAM IF NECESSARY. A gaseous Ammonia actuates a Carnot power cycle in which the respective volumes at the four corners of the cycle, starting at the beginning of the isothermal expansion, are V1 = 12, V2 = 15, V3 = 330.25 and V4 = 264.20. Determine (a) the overall expansion ratio and (b) the thermal efficiency.
Water enters a turbine pump at 30kPa (vf= 0.0010223 cu. m per kg) and discharges at 2.8 MPa. The turbine work is 380 kJ/kg. What is the percentage of turbine work output required to operate the pump of a steam power plant? 0.75% ANSWER
In a reaction turbine, the drum diameter is 2.15 m, speed of turbine is 750 rev/min and the steam flow is 14.2 kg/sec. At a particular ring of blades, the blade height is 15.875 cm and the discharge angle (α & ϕ) is 25°. Here, the pressure of steam is 0.04 N/mm2 abs, and its dryness fraction is 0.97. Determine the following: 1.Heat drop, in kJ, through this turbine pair, assuming turbine efficiency of 80% a. 141.6 b. 77.14 c. 12.47 d. 22.89 e. 42.02
A 2.00 mol sample of an ideal diatomic gas is taken through a reversible cycle A → B → C → A as shown in the figure below. Process A → B is isothermal expansion. For the cycle, calculate: a) the work done by the gas, b) the heat energy added to the gas, c) the heat energy exhausted by the gas, d) the thermal efficiency, e) the change in entropy of the gas. f) Determine the efficiency of a Carnot engine operating between the same temperature extremes, R = 8.314 J/mol K Data at vertices for the above PV diagram are as follow: PA = 5.00 x 105 Pa, VA = 1.00 x 10 -2 m3, PB = 1.25 x 105 Pa, VB = 4.00 x 10 -2 m3 PC = 1.25 x 105 Pa, VC = 1.00 x 10 -2 m3
1. An engine from a quarry vehicle used in the Build a Beach program of DEMR has a power requirement of 560 kW. Per hour of its operation, it ejects 234 MJ into its surroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below. A. How much work (MJ) is done by the engine per hour of operation? B. What is the efficiency (%) of the engine?C. What is the temperature (°C) of the hot reservoir? 2. Determine the entropy change (kJ/K) associated to the conversion of 10 kg of ice at -11 °C to steam at 121 °C. 3. Anna and Beth are using another rare metal, the nth metal (c = 0.600 J/g-℃), to build the 5-kg cuirass of their design. Initially, the metal is at 2250 K. It is then submerged to 10 kg of water at 15 °C. If the remaining liquid water after submerging the metal is 8.5 kg, solve for the net entropy change (kJ/K) of the system.
How to show that for reversible cycles ,the heat transfer also ratio QH/QL can be replaced by the absolute temperature ratio TH/TL.