Determine the diameter of a cast iron pipe which is required to carry water at 10 degrees C at the rate of 250 liters/sec, if the loss of head is not to exceed 2m per 100m length of pipe. The average height of the pipe wall projection (e) is 0.36 mm and kinematic viscosity of water at 10 degrees C is 1.3x10^-6 m^2/s.

Determine the diameter of a cast iron pipe which is required to carry water at 10 degrees C at the rate of 250 liters/sec, if the loss of head is not to exceed 2m per 100m length of pipe. The average height of the pipe wall projection (e) is 0.36 mm and kinematic viscosity of water at 10 degrees C is 1.3x10^-6 m^2/s.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three pipes connected in series with lengths L1 = L2 = L3 = 300 m and diameters D1 = 75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 50 mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Haaland and Darcy-Weisbach Formula, determine the following: a. Which pipe has the highest Renoylds Number? b. Which pipe is the smoothest? c. Compute the total head loss
Include a free body diagram. A 12′′ pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the pressure at point A in the pipe is 40 psi. A differential gage is attached to the pipe at A and at a point Bdownstream that is 10 ft higher than A. The deflection of mercury in the gage is 3.33 ft, indicating a greater pressure at A. What is the lost head A to 5?
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
Compute the head loss (in meters) in 2000 m of horizontal, steel pipe with nominal pipe size of 300 mm and SCH 30. The pipe is carrying water with an average velocity of 1.88 m/s. Take water at 20°C to have a viscosity of 1.00E-3 Pa-s and density of 1000 kg/(m^3). Take the roughness of steel pipe to be 0.048 mm. Round your answer to 2 decimal places.
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12)
A 11 inches pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the pressure at point A in the pipe is 30 psi. A differential gage is attached to the pipe at A and at a point B downstream which is 8 ft higher than A. The deflection of mercury in the gage is 3.33 ft, indicating a greater pressure at A. What is the lost head A to B? Show the diagram.
Water 20°C, flows at a rate of (0.05 m3/sec) in (20-cm) asphalted cast-iron pipe. What is the head loss per Kilometer of the pipe, if the Kinematic viscosity of water (v= 1.0 x 10* m2/sec) , and friction factor in the pipe (f= 0.019) ?
A concrete pipe 750 mm in diameter is laid to a gradient of 1 in 200.The estimated value of Manning’s ?is 0.012m−1/3s.Calculate the discharge when:(a)the pipe is full;(b)the depth is 90% of maximum.Explain why the answer in (b) exceeds th
Two concrete pipes are connected in series. The flow rate of water through the pipes is 0.14 m3/s with atotal friction loss of 14.10 m for both pipes. Each pipe has a length of 300 m. If one pipe has a diameterof 300 mm, what is the diameter of the other one? Neglect minor losses.
if relative roughness of cast iron circular pipe is 0.25, water is following at temperature of 29 degree centigrade with average velocity of 5 m/sec. Calculate major head loss by using Moody Diagram, given that length of pipe is 127 m and diameter is 2.1 inches. A
Water flows in a 350mm- diameter pipe at the rate of 600 liters per second. The pipe has a length of 64m. Compute the head loss using Darcy Weisbach formula with f=0.028. Compute the head loss using Hazen William’s Formula with C=92. Compute the head loss using Manning’s formula with n=0.012