Determine the distribution of heat flux for the square heated plate in the figure. Use a relaxation factor of 1.2 and Iterate to eg= 1%.Assume that the plate is 40 x 40 cm and is made out of aluminum [k'= 0.49 cal/(s-cm"C)).150°C(1. 3)(2, 3)(3, 3)(1. 2)(2, 2)(3. 2)50°C50°C(1,1)(2.1)(3, 1)0°C

There is no heat flux distribution in horizontal direction because the temperature of walls are same…

Determine the distribution of heat flux for the square heated plate In the figure. Use a relaxation factor of 1.2 and iterate to ɛg= 1%. Assume that the plate is 40 x 40 cm and is made out of aluminum [k'= 0.49 cal/(s-cm-C). 150°C (1.3) 2.3) (3, 3) (1. 2) 3.2) 50°C 50°C (2.1 (3.0

Determine the distribution of heat flux for the square heated plate In the figure. Use a relaxation factor of 1.2 and iterate to ɛg= 1%. Assume that the plate is 40 x 40 cm and is made out of aluminum [k'= 0.49 cal/(s-cm-C). 150°C (1.3) 2.3) (3, 3) (1. 2) 3.2) 50°C 50°C (2.1 (3.0

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.51P: 2.51 Determine by means of a flux plot the temperatures and heat flow per unit depth in the ribbed...

See similar textbooks

Related questions

Q: A gas within a piston-cylinder assembly undergoes a process from a state where P = 100 kPa, V = 0.09...

Q: What advantage might the commercially packaged coolant material have over ice other than it produces...

A: Advantages that commercially packed coolants have over ice: 1. One of the major disadvantages of usi...

Q: 2000 lb 4000 Ib ft 40X00 lb ft B 8 ft FIG. P4. 54 00

Q: 3. A trash compactor pushes down with a force of 500 N on a 3 cm2 input piston, causing a force of 3...

Q: The crank link AB of the crank and slider mechanism has an angular velocity of 7 rad/s“, both direct...

Q: how to calculate water friction head loss given data : Tower tank height = 110 M volume of tank = 20...

A: Head loss alludes to an estimation of the energy disseminated in a liquid framework because of conta...

Q: A sign is supported by a pipe (see figure)having an outer diameter 110 mm and inner diameter90 mm. T...

A: Given that, Outer diameter of pipe, do=110 mm,Inner diameter of pipe, di=90 mm,Wind pressure, P=1.5 ...

Q: 7.4 A reservoir containing air at 2 MPa is connected to ambient air (y = 1.4) at 101 kPa through a C...

A: The Prandtl number (Pr) or Prandtl bunch is a dimensionless number, named after the German physicist...

Q: A vertical pole of solid, circular cross sectionis twisted by horizontal forces P =1100 lb actingat ...

A: P=1100lbc=5.0inL=14ina) Allowable stress = 4500psib) G=10,800ksic)k=33kips/in at 2c/5 To-Find:- a) ...

Q: A power plant operates between pressures of 80 bar and 0.1 bar in an actual Rankine cycle. The maxim...

A: GivenP1=80barguage P2=0.1bar guage T1=650oCm=5kg/sηP=82%ηT=93%

Q: Show the temperature distribution in degree Celsius in an exhaust valve of IC Engines.

A: Internal combustion engines usually consists of two types of engine valves Inlet valves and exhausts...

Q: A particle undergoes an underdamped vibration with the following equation:(image below) What are the...

Q: Q. A cantilever, 2.5 m long carries a UDL of 20 kN/m. The breadth of the section remains constant an...

A: When a beam is subjected to pure bending. Then, the governing equation of this pure bending is given...

Q: A solid circular steel cylinder S is encasedin a hollow circular aluminum tube A. The cylinderand tu...

A: According to Strength criterion, if a load is acting on the shaft and if the stress induced due to t...

Q: A front tire has excessive wear on both edges ofthe tire tread. The most likely cause of this proble...

A: Given data : Front tire Excessive wear

Q: An aluminum wire of length 2.0 m and diameter 5 mm is used to hang a load of 100 kg. The modulus of ...

Q: The 20-gg bullet is traveling at 400 m/sm/s when it becomes embedded in the 2-kgkg stationary block....

Q: Position tolerances applied to features that result in a fixed fastener condition usually require a(...

A: Position tolerance applied to feature that result in a fixed fastener condition usually require 1) p...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: Ah Assignment: The losses per unit length of pipe in tubulent flow through smnooth pipe depend ipon ...

A: ∆hL=f V, D, g, μ, ρ

Q: Water at 4.4oC with a density of 1000 kg/ m3 and a viscosity of 1.55 cP is to flow through a horizon...

Q: In 3-axis milling, the table feedrate is 756.00 mm/min. Using a 10mm endmill to cut the material wit...

Q: A cylindrical assembly consisting of a brasscore and an aluminum collar is compressed by a loadP (se...

A: (a) Calculate the cross-section area of the aluminum collar from the given figure. A1=π440 mm2-25 mm...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: A 250mm diameter horizontal jet discharging at 491 L/s impinges on a vertical flat plate. Which of t...

A: Givendiameter of the jet d=250mm=0.250mdischarge Q=491 Ltr/s=0.491 m3/sspeed of plate u=2m/s

Q: The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bea...

A: Answer: The downward force P is 1212.85 N.

Q: 0.2 m3 of a gas at 105 kPa and 27 0C is compressed until the temperature is 282 0C and the pressur...

Q: Part A The motor winds in the catio wth a constant aceleration, such tat the 32-kg crate moves a dis...

A: Find the tension in cable Given data:- Mass = 32 kg S=6 m Time = 3 seconds

Q: A rectangular column with cross-sectionaldimensions b and h is pin-supported at ends A and C(see fig...

A: Cross-Sectional Dimensions b and h pin supported at A and CAB=L2BC=L2

Q: 12. A piece of copper wire is initially at 150 C. We now expose this wire to air at 38 C. Find a) th...

Q: 1. Sketch a diagram for the experimental instrumentation and devices. 2. State any possible error so...

A: Electrical boiler ***As per our company policy we are supposed to do only 3 subpart if you need the...

Q: Using thin airfoil theory, calculate cl when α = 2.4°. (Round the final answer to three decimal plac...

A: Given: angle = 2.4 deg

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of 269...

Q: 26. A tank containing air is pressurized to 1.7 MPa and 30 C. A valve is now opened to discharge air...

A: Given data, Air pressure inside the tank, P = 1700 kPa Air temperature inside the tank, T = 30 °C Fl...

Q: A car travels around a circular track at 16 m/s. As soon as it reaches point P it accelerate: a, = m...

Q: What is the torque applied, in Nm, to a 91 mm shaft if the resulting shear stress on the outside sur...

Q: The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the...

A: Given Data The diameter of the shaft is: d=8×10-3 m The length of the shaft is: L=200×10-3 m The al...

Q: 5- An aircraft is flying at an altitude of (12000 m) (T = 216.65 k, P = 0.193bar) at a Mach number o...

Q: Explain why managers use marketing dashboards and marketing metrics.

A: Given Data : Marketing dashboards

Q: It takes 34 s for the 60-Mg tugboat to increase its speed uniformly to 25 km/h, starting from rest. ...

Q: The parabolic velocity distribution in a channel flow is given by u(y) = 0.2(1 − y^2) m/s with y mea...

Q: The maximum speed of an object vibrating with simple harmonic vibrations is 3 cm/s with a period of ...

A: Given : Vmax = 3 cm/s t = 0.15 sec To Find : a. Maximum amplitude (A) =? b. Maximum accel...

Q: Bar ABC of circular section is fixed at its ends and is subjected to a couple T. Section AB has a di...

Q: t takes 34 s for the 60-Mg tugboat to increase its speed uniformly to 25 km/h, starting from rest. T...

A: Given:mass of tugboat, mt=60 Mg or 60000 kgmass of barge, mb=84 Mg or 84000 kgspeed of tugboat, v=25...

Q: Compute the coordinates of the centroid (a, y) of the area shown. y y = a /bx %3D CC BY NC SA 2016 E...

Q: Real Pressure, Barometer Room Volumetric Mass Rate of Trail Speed Difference Pressure Temp. Rate of ...

Q: e allowable position tolerance that may be applied to each part in a

A: Determine The applied allowable position tolerance

Q: 3- Comparing the theoretical results and calculations with the process and discussing the difference...

Q: How can you improve performance of engines to achieve more power?

Q: 1. A cantilever of square cross section as shown was made of mild carbon steel SAE 1020, as rolled, ...

A: d4ydx4-PEIδx-L3..............1y(0)=0; y'(0)=0y(L)=0,y'(L)=0y''(0)=c, ; y'''(0)=c2taking integration ...

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Determine the distribution of heat flux for the square heated plate in the figure. Use a relaxation factor of 1.2 and Iterate to eg= 1%.
Assume that the plate is 40 x 40 cm and is made out of aluminum [k'= 0.49 cal/(s-cm"C)).
150°C
(1. 3)
(2, 3)
(3, 3)
(1. 2)
(2, 2)
(3. 2)
50°C
50°C
(1,1)
(2.1)
(3, 1)
0°C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A metal rod having initial length (L) expands to 14m after heating the rod at 40°C from a room temperature of 28° C, Calculate the initial length of rod by taking the expansion coefficient as 51 × 10-5 K-1
In the figure below, it is known that the thermal conductivity of k1 = 0.06 W/mK, k3 = 0.04 W/mK, and k4 = 0.12 W/mK. The thickness of the layers is L1 = 1.50 cm, L3 = 2.8 cm, and L4 = 3.50 cm. Known temperatures T1 = 30°C, T12 = 25°C, and T4 = -10°C. Energy transfer through walls is constant. How much is T34?
A clearance of 2.8 mm was applied to the laid steel railroad rails that are 11m long,at a temperature of 13°C. At what temperature will the rails just touch each other? Assume α = 11.7 x 10-6/°C and E = 200 GPa
A very long copper rod (k =372 W/m•C) is 2.5 cm in diameter and has one end maintained at 93° C. The rod is exposed to 38° C fluid. The convective coefficient is 3.5 W/m^2•C. How much heat is lost by the rod?
A steel rod (k = 30 W/m degree) 1 cm in diameter and 7 cm long protrudes from a wall which is maintained at 100 degree Celsius. The rod is insulated at its tip and is exposed to an environment with h = 50 W/m2 degree and t a = 30 degree Celsius. Calculate the fin efficiency
Required info: There is a 2.00 cm thick stagnant air pocket. a) What thickness of cork would have the same R-factor as the stagnant air pocket? The thermal conductivity of air is 0.0230 W/m-K and of cork is 0.0460 W/m-K. b) What thickness of tin would be required for the same R-factor as a 2.00-cm-thick stagnant air pocket? The thermal conductivity of air is 0.0230 W/m:K and of tin is 66.8 W/m-K. THANK U
plz answer this ASAP,thx One surface of a copper plate that is 3 cm thick has a constant temperature of 400 ° C while the temperature of the other surface is kept constant at 100 ° C. Describe the temperature profile and how much heat is transferred across the plate ?, k copper = 380 watts/m.k with a cross -sectional area of 4 cm².
A thick-walled tube of stainless steel (L = 0.50 m; k = 21.63 W/m-K) with an inside diameter of 0.0254 m and outside diameter of 0.0508 m, is covered with an insulation (∆x =0.0254 m) with k = 0.2423 W/m-K. If the inside wall temperature of the pipe is at 400 oC, calculate the temperature at the interface between the metal and the insulation (in oC) if the outside surface of the insulation is at 29.8 oC. 99 K in Pa.
2.51 Determine by means of a flux plot the temperatures and heat flow per unit depth in the ribbed insulation shown in the accompanying sketch.
Awatermelon initially at 35°C is to be caoled by dropping itinto a lake at 15°C. After 4 h and 40 min of cooling the center temperature of watermelon is measured to be 20°C. Treating the watermelon 25 a 20-c-diameter sphere and using the properties k = 0.618 Wim
Aluminum balls are heated up to 580 K and then exposed to air at 283 K to cool down with an average heat transfer coefficient of 25 W/m2·K. The balls are 3 cm in diameter. Find the temperature at r = 0.5 cm after 75 seconds of exposure. Is the lumped capacitance an acceptable solution here? [Ans.: 329 K].
A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?