Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 2.51P
Determine by means of a flux plot the temperatures and heat flow per unit depth in the ribbed insulation shown in the accompanying sketch.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Question No.14: a) Derive the expression for temperature distribution and heat dissipation in an infinite long fin of rectangular profile.
b) Explain about Buckingham’s π theorem.
1-mm-diameter cylindrical resistor, insulated with a sheath of thermal conductivity, k, of 0.12 W/m-K, is located in an evacuated enclosure. The surface emissivity of the sheath is 0.85. The resistor is maintained at 450 K and the enclosure is at 300 K.
What is the radius of the sheath that maximises the rate of heat loss from the resistor? Evaluate the corresponding maximum heat rate per unit length of the resistor and the sheath surface temperature. Determine the value of the parameter hirerlk where h, is the linearised radiation heat transfer coefficient at the critical radius, rer. Comment on your results. State all assumptions made.
What is the rate of heat loss per unit length from the uninsulated resistor if its surface emissivity is the same as the sheath surface of the insulated resistor?
Determine net radiant-heat exchange between the closed ends of a hollow
cylinder 12-in. in diameter and 4-in. long. The ends are of Cr-Ni alloy with
one end heated electrically to a temperature of 1900 °F and the other end
maintained at 125 °F. The side wall of the cylinder is substantially
nonconducting and reradiating.
Chapter 2 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 2 - A plane wall, 7.5 cm thick, generates heat...Ch. 2 -
2.2 A small dam, which is idealized by a large...Ch. 2 - 2.3 The shield of a nuclear reactor is idealized...Ch. 2 - A plane wall 15 cm thick has a thermal...Ch. 2 - 2.5 Derive an expression for the temperature...Ch. 2 - A plane wall of thickness 2L has internal heat...Ch. 2 - 2.7 A very thin silicon chip is bonded to a 6-mm...Ch. 2 - 2.9 In a large chemical factory, hot gases at 2273...Ch. 2 - 2.14 Calculate the rate of heat loss per foot and...Ch. 2 - 2.15 Suppose that a pipe carrying a hot fluid with...
Ch. 2 - Prob. 2.16PCh. 2 - Estimate the rate of heat loss per unit length...Ch. 2 - The rate of heat flow per unit length q/L through...Ch. 2 - A 2.5-cm-OD, 2-cm-ID copper pipe carries liquid...Ch. 2 - A cylindrical liquid oxygen (LOX) tank has a...Ch. 2 - Show that the rate of heat conduction per unit...Ch. 2 - Derive an expression for the temperature...Ch. 2 - Heat is generated uniformly in the fuel rod of a...Ch. 2 - 2.29 In a cylindrical fuel rod of a nuclear...Ch. 2 - 2.30 An electrical heater capable of generating...Ch. 2 - A hollow sphere with inner and outer radii of R1...Ch. 2 - 2.34 Show that the temperature distribution in a...Ch. 2 -
2.38 The addition of aluminum fins has been...Ch. 2 - The tip of a soldering iron consists of a 0.6-cm-...Ch. 2 - One end of a 0.3-m-long steel rod is connected to...Ch. 2 - Both ends of a 0.6-cm copper U-shaped rod are...Ch. 2 - 2.42 A circumferential fin of rectangular cross...Ch. 2 - 2.43 A turbine blade 6.3 cm long, with...Ch. 2 - 2.44 To determine the thermal conductivity of a...Ch. 2 - 2.45 Heat is transferred from water to air through...Ch. 2 - 2.46 The wall of a liquid-to-gas heat exchanger...Ch. 2 - Prob. 2.47PCh. 2 - The handle of a ladle used for pouring molten lead...Ch. 2 - 2.50 Compare the rate of heat flow from the bottom...Ch. 2 - 2.51 Determine by means of a flux plot the...Ch. 2 - Prob. 2.52PCh. 2 - Determine the rate of heat transfer per meter...Ch. 2 - Prob. 2.54PCh. 2 - 2.55 A long, 1-cm-diameter electric copper cable...Ch. 2 - Prob. 2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4arrow_forwardA section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kP=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces. Repeat Problem 1.34, including a contact resistance of 0.1 K/W at each of the interfaces.arrow_forwardWrite the expression for critical radius of insulation for a cylindrical pipe. Consider aninsulated pipe exposed to the atmosphere. Will the critical radius of insulation begreater on calm days or on windy days? Why?arrow_forward
- Calculate the thickness of the magnesia insulation necessary to restrict the heat loss to 5 BTU/hr-ft2 through the walls of a furnace having inside and ambient temperatures of 1500 oF and 150 oF, respectively. The furnace wall is ¼ in, steel plate and 3 in refractory lining. Thermal conductivity in BTU/hr –ft-oF are kref = 0.6, ksteel = 26, kmag=0.03arrow_forwardCalculate the overall heat loss and the temperature profile for each interface if the length of the cylinder is 50 m.Please write your answers legibly.arrow_forwardA thick-walled tube of stainless (A) having k=21.63 W/m.K with dimensions of 0.0254 m ID and 0.0508 m OD is covered with a 0.0254-m layer of asbestos (B) insulation, k=0.2423 W/m.K. The inside wall temperature of the pipes is 811K and the outside surface of the insulation is at 310.8 K. For a 0.305-m length of pipe, calculate the heat loss and also the temperature at the interface between the metal and insulation. (q = 331.7 W; T2 = 805.5 K)arrow_forward
- Derive an expression for heat conduction through a composite plane wall of n- layers.arrow_forwardWhat is a composite wall? Derive the relevant equations for heat conduction through composite wall?arrow_forwardA furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?arrow_forward
- Calculate the quantity of heat conducted per minute through a duralumin circular disc 127 mm diameter and 19 mm thick when the temperature drop across the thickness of the plate is 5 degrees Celsius. Take the coefficient of thermal conductivity of duralumin as 150 W/(m-K).arrow_forwardA sphere of radioactive material of radius aR is wrapped with a ceramic casing of outer radius R.The heat flux density emitted by the sphere radioactive on its surface is qaR. Find the temperature profile of the spherical shell if the thermal conductivity of the housing material varieswith its radius according to k = Kr (where K is a constant and r is the distance from the center of thesphere) and the temperature outside the casing is keeps T constant Rarrow_forwardIn order to reduce the heat loss through a large furnace wall, the decision has been made to add external insulation. Calculate the thickness of insulation required to reduce the heat loss by 75%. Before the change is made, no outer steel shell is used.Data: Refractory brick and wall brick:k = 0.87 W m-1 K-1Insulation: k = 0.090 W m-1 K-1•Steel: k = 43 W m-1 K-1h = 55 W m-1 K-1 (inside furnace).h = 11 W m-1 K-1 (outside furnace).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license