Strength and materials Determine the ff.1. The horizontal shearing stress of the fiber 50mm from the top and bottom of thebeam at midspanA10 kN/m50KN12 KN/m24BIn c ImD2mR₁+1007100 | 200 + 100N.A.15पुR2001amCA250mmof 200300 mm200mm

Sure, The question asks for the horizontal shear stress of the beam 50mm from the top and bottom of…

Answered: Determine the ff. 1. The horizontal…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
The shear capacity V if a steel wide flange section, 600 mm deep whose web is 9 mm thick, is closest to: Assume fy = 200 MPa. Take FV = 0.4 Fy a. 645 kN b. 413 kN c. 507 kN d. 432 kN
Two forces act on the screw eye. If F1 = 400 N andF2 = 600 N, determine the angle θ (0° ≤ θ ≤ 180°) betweenthem, so that the resultant force has a magnitude ofFR = 800 N.
Determine the deflection at midspan of the structure Group of answer choices (-5wL^4)/384EI (5wL^4)/384EI (wL^3)/24EI (-wL^3)/24EI
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
Given: Signage subjecting 1.606 kPa pressure. Signage = 2.404 m x 1.01 m Offset of signage from pole center = 0.404 m Signage center distance from the ground = 8 m 1. Determine max shear force at the base of pole in kN. 2. Determine max moment at the base of pole in kN-m. 3. Determine max torque at the base of pole in kN-m.
For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the shear diagram of the line from B to C?A.15 KN/mB.16 KN/mC.24.46 KNmD.11.26 KNmThe change in moment [KNm] of the diagram above from point A to the concentrated load is nearest toA.98B.99C.100D.101
Calculate V(x) and M(x) between x = 2ft and x = 7ft (measured from the left end) of thebeam below: Ay = +1865 # (upwards) and MA = +3765 ft#(counter-clockwise); the support reaction at the roller C is Cy = +675 # (upwards). There isa HINGE at B, with internal forces bx = 0 and by = ±175 #.
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Draw the shear and moment diagrams given that Ra=110.2 kN, Rb=310.1 kN, Rc=220.6 kN, Ma=-124.5 kN m, Mb =-258.9 kN m, Mc = -160.5 kN
The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.07 m from the pin if P = 499.99 kN.
Determine the reactions at a and b for the beam subjected to the concentrated loads Ay= ? (Not 8.77 or 4.85 previous failed attempts on my behalf) bx = 7.2 Ax = ? (Not 1.9 or -.3365)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Determine the ff. 1. The horizontal shearing stress of the fiber 50mm from the top and bottom of the beam at midspan A 10 kN/m 50KN 12 KN/m 24 B In c Im D 2m R₁ +1007 100 | 200 + 100 N.A. 15 पु R 2001am CA 250mm of 200 300 mm 200mm