Determine the forces in all members using method of joints and specify whether the force is in tension (write T only) or in compression (write C only). Support at A is a roller support and support at E is a pin support. L1 L2 L3 L2 L1 5 m 5 m 5 m C 5 m A D E 3m 30,964० 30.964 30.964° 30.964 F H 2m 21.801 21.801° SET A SET B L1 2.5 L2 4 3.5 L3 3.5

Determine the forces in all members using method of joints and specify whether the force is in tension (write T only) or in compression (write C only). Support at A is a roller support and support at E is a pin support. L1 L2 L3 L2 L1 5 m 5 m 5 m C 5 m A D E 3m 30,964० 30.964 30.964° 30.964 F H 2m 21.801 21.801° SET A SET B L1 2.5 L2 4 3.5 L3 3.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thecable of length 15m supports the forces W1 = W2 = W at B and C. (a) Derive the simultaneous equations for β1, β2, and β3. (b) Show that the solution to these equations is β1 = 41.0◦, β2 = 9.8◦, and β3 = 50.5◦. (c) Compute the force in each segment in terms of W.
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
The ends of the triangular plate are subjected to three couples. Determine the magnitude of the force F so that the resultant couple moment is 500 N.m clockwise Choices are: 682.85 N 982.85 N 729.71 N 829.71 N
Three forces act on the bracket. Determine themagnitude and direction θ of F so that the resultant force isdirected along the positive x' axis and has a magnitudeof 8 kN.
The beam ABC shown in the figure is simplysupported at A and B and has an overhang from B to C.The loads consist of a horizontal force P1 = 4.0 kNacting at the end of a vertical arm and a vertical forceP2 = 8.0 kN acting at the end of the overhang.(a) Determine the shear force V and bendingmoment M at a cross section located 3.0 mfrom the left-hand support. Note: Disregardthe widths of the beam and vertical armand use centerline dimensions when makingcalculations.(b) Find the value of load P2 that results in V = 0 ata cross section located 2.0 m from the left-handsupport.(c) If P2 = 8.0 kN, find the value of load P1 thatresults in M = 0 at a cross section located 2.0 mfrom the left-hand support.
Using the method of joints, determine the forces in teach member of the truss. State whether the member is in tension or compression. F1 = 3kN, F2 = 6kN, and h = 1.5m
Determine the forces in the truss shown inFigure by using method of joints. (Point A is a pinned support and Point B is a roller support) AB= 53 , CB=83kN A=5, B=3, C=8
Compute the force in member BD in kN. P1=117 kN, P2=72 kN and x = 7.8 m. Write numerical value only and in 2 decimal places
Find the forces in the truss.all horizontal member are 1minclude C or T T1, T3, T4, T8, T22, T28, T30, T32
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
The ends of the triangular plate are subjected to three couples. Given that F1= 600 N, F2 = 255 N, and α= 50°, determine the magnitude of the force F so that the resultant couple moment is 400 N.m clockwise.