Answered: Determine the forces in members BC and…

Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression B 15 C 15 D 11' AZK 15' G 12 kips 51% E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: a) Stresses :σx=2800 psiσy=-1400 psiτxy=-4200 psi

Q: for a confined aquifer 150 ft thick and composed of fine sand of permeability 1.96 ft per hr, a well…

A: Given :

Q: 4. A car is traveling downhill on a suburban road with a grade of 4% at a speed of 35 mph. Determine…

A: stopping sight distance (SSD) One sort of sight distance utilized in road design is stopping sight…

Q: A clockwise traverse ABCDEA was surveye Find the length and direction of line A

A: SUm of departures shoulde be zero∑ D=0137.137+11.027+Lsinθ=0Lsinθ=-148.164SUm of Latitude shoulde be…

Q: A simply supported beam is subjected to twopoint loads, each P = 500 lb, as shown in the figure.The…

A: Given data:

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

A: Given To find Length and direction of line AD

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

Q: The table below is the page of a level field book. Calculate the reduced levels of points C, F and H…

A: To Determine Reduced level ( R.L ) of points C,F,H

Q: double tee cross section is used for the beam shown below. Assume the following lengths and loads:…

A: Given: a = 15ft b= 8 ftc= 13ftP = 22000 lbQ =7000 lb bending stress equation MI =σyM = max bending…

Q: A parabolic sag curve has a sight distance of 118 m. the tangent grades of the curve are -3% and…

A: Given Data Sight distanceS=118 mThe gradients are N1=-3%N2=5% Here it is asked to calculate the…

Q: In a plate girder subjected to a bending moment of 200 kN-m, the width and thickness of flange are…

A: Given- Bending moment M=200 kN-mwidth b=200 mmthickness t=10 mmfy=250 MPa

Q: For the beam loaded as shown, draw the shear and moment diagrams. R₁ 50 kN 2 m m 7m 20 kN/m R₂ 40 kN…

Q: A material of the section is 2.5cm Calculate the least radius of gyration. Calculate the slenderness…

Q: 4m 20 KN 43 5 kN/m E = 200 GPa I = 2X 108 MMY

A: Using superposition theorem

Q: a. Determine the centroid of the composite figure. b. Calculate the moment of inertia with respect…

A: Given data:-

Q: Which table one property of silt soils

A: Classification of soil is done on various criteria. Some of them are : -Particle Size classification…

Q: WHERE DID YOU GET THE As= 6000 mm can you explain briefly?

A: Given 12-25mm Φ bar Required As per solution provided by another expert, explain how As = 6000 mm²

Q: Which of the following best describe the structure?

A: Statical indeterminacy = Total reaction -No of equilibrium equation -releases

Q: Truss System A F D X VB E L75X75X6 C G SOLVE FOR AXIAL FORCES OF EACH MEMBER. X = 20 KN, Y = 90 KN.…

Q: For the distributed loads shown below, calculate the magnitude of the equivalent point load acting…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.8 in., b = 6 in., d = 4.0…

A: Given data:

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: a. Concrete Pedestal b. Steel Plate c. Stiffener cm) (Thickness=0.5 d. Steel Pipe (Outer dia-10 cm,…

A: Since you have posted a question with multiple sub parts, we will solve first part for you. To get…

Q: For the beam loaded as shown, draw the shear and moment diagrams. 50 kN 1 m 4 m 20 kN/m 50 kN 1 m…

Q: In a parabolic vertical curve, if the rising grade is 2% followed by a downgrade of 2%, and the rate…

Q: The latitude for the figure can be given as (0 = 50° 34') 0 245m 161.34m O 155.62 O 160.43m O 165m O…

A: Given data in question Length Angle To find out Latitude

Q: The column is 480" long and is Ball and Socket supported on each end. The column is A36 steel with E…

A: Section C10×15.3 Properties: Ag= 4.48 in2Ix = 6.73 in4Iy = 2.27 in4x = 0.634 in The total moment of…

Q: An overhanging beam is loaded as shown below. Calculate the deflections under the two loads 80kN and…

A: GIVEN DATA:-⇒Overhanging beam (single side) of span = 12 m⇒Loads = point loads:-(1) 80 KN(2) 120…

Q: Instructions: Solve the following problems as instructed. Boxed final answers and round off to the…

A: Given :

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

Q: Ao B C D . Tex₁ - x1 F1 (2.000x10^1) KN • F2= (4.0000x10^1) kN x1 (3.0000x10^0) m .x2= (4.00x10^0) m…

Q: Q1: Discuss seven practical applications of Lagrangian and Eulerian descriptions of fluid flow.

A: Lagrangian descriptions of fluid flow: In here that the fluid particles are marked, so the flow…

Q: The 51 mm diameter rubber rod is placed in a hole with rigid, lubricated walls. There is no…

A: Given: Load Length of rod Diameter of rod Modulus of elasticity Poisson ratio To find: Change…

Q: 1. Using Rayleigh-Ritz method, determine the expressions for displacement and stress in a fixed bar…

A: The given figure is shown below:

Q: For the shear diagram as shown, draw the load and moment diagrams. V (KN) 2 * 36 -40 1.6 16 2.4 20 2…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: An oblique shock wave at an angle of 35 degrees occurs at leading edge of a symmetrical wedge. Air…

A: Given data:-Angle of oblique shock wave, θ=35° For upstream of the wave; Mach number, M1=2 Pressure,…

Q: Determining the relative positions of points on above or beneath the surface of the earth by means…

A: Given :

Q: A solid steel shaft supports loads PA=490 N and PD = 400 N, as shown. Assume L₁ = 180 mm, L₂ = 620…

Q: A particle which moves with curvilinear motion has coordinates in millimeters which vary with the…

Q: The extruded plastic shape has dimensions of D-31 mm, d-25 mm, a = 96 mm, and t = 6 mm. (a)…

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the…

Q: From the figure, determine R.L of Q from A? al B #2 D S R.Lof Q = R.L of A + h + H2 R.Lof Q = R.L of…

Q: Meriam red oil, SG=0.827 P2.32 Water A 18 cm H 35 cm B Mercury

A: Given data:- The PB-PA=89.5 kPa=89500 Pa The specific weight of water is, Wwater=9790 N/m3 The…

Q: 2a) Calculate the magnitude of the resultant of two forces F₁ and F₂ in Newtons.

A: Given, F1= 305N F2= 461N α= 28° β= 41°

Q: water flows from a reservoir (A) showe in through a pipe of diameter (di=120mm) and lengh (Lis 20 m…

Q: Example 5: The followings are the F.B. of lines. Calculate their B.B. (1) AB N 18° 0' E 1 (2) BC S…

Q: to a set of blades moving at 180 m/s.the blade angle at outlet is 25 degree and blade velocity…

A: Given:- angle of 16 degree , deliver 1 kg of steam per second at a speed of 720 m/ set of blades…

Q: 1. You run a frequency analysis for a pretensioned beam structure (at one end the beam is…

A: An increase in the axial compression increases the frequency of the beam and vise versa ; The…

Q: A reinforced concrete beam has a width of 400 mm and an effective depth of 600 mm. It is reinforced…

A: Solution: Stress strain Profile:

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression.
12 kips
Answers:
BC-
11'
Z
15' G
CG=
B 15' C 15' D
i
51°
E
kips
kips

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
Solve for the force of member BC using method of sections. Ans. 60kN
P1 = 445 N P2 = 501 N Determine the force in member DC, use a positive value for tension or a negative for compression
NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces of the hinge at B acting upon member AC as shown.
Compute the force in member BD in kN. P1=186kN, P2=107 kN and x = 7.9 m. Write numerical value only and in 2 decimal places
A vertical force P = 10 lb is applied to the ends of the 2-ft cord AB and spring AC. If the spring has an unstretched length of 2 ft, determine the angle θ forequilibrium. Take k = 15 lb/ft.
Determine the vertical displacement of joint C. The truss is made from A992 steel rods each having a diameter of 1 in.
Solve the slope at each support and the deflection at the midspan (pt. C), interms of the flexural rigidity. Use EI as constant, l=10 meters, P=75 kN.
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression.Assume F = 3200 N, a = 1.8 m, b = 3.6 m, θ= 40°.
Set P1 = 53 kN, P2 = 36 kN A) Determine the force in member AD and state if the member is in tension or compression B) Determine the force in member BC and state if the member is in tension or compression C) Determine the force in member BD and state if the member is in tension or compression D) Determine the force in member CD and state if the member is in tension or compression B)
Compute the force in member BD in kN. P1=117 kN, P2=72 kN and x = 7.8 m. Write numerical value only and in 2 decimal places
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN