The extruded plastic shape has dimensions of D-31 mm, d-25 mm, a = 96 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V-370 N. (b) If the allowable shear stress for the plastic material is 1300 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? TO Z Answer: (a) TA= (b) V= dik a kPa N

The extruded plastic shape has dimensions of D-31 mm, d-25 mm, a = 96 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V-370 N. (b) If the allowable shear stress for the plastic material is 1300 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? TO Z Answer: (a) TA= (b) V= dik a kPa N

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.25P: Refer to Figure 8.27. The flexible area is uniformly loaded. Given: q = 300 kN/m2. Determine the...

See similar textbooks

Similar questions

Refer to Figure 8.27. The flexible area is uniformly loaded. Given: q = 300 kN/m2. Determine the vertical stress increase at point A located at depth 3 m below point A (shown in the plan). FIG. 8.27
The extruded plastic shape has dimensions of D = 37 mm, d = 31 mm, a = 84 mm, and t = 8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 325 N.(b) If the allowable shear stress for the plastic material is 1050 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 21 mm. d = 17 mm. a = 87 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 360 N. (b) If the allowable shear stress for the plastic material is 1050 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D- 31 mm, d - 25 mm, a - 93 mm, and t - 6 mm.(a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V -(b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can beapplied to the extrusion?
According to the elastic theory, the vertical stress induced by a point load of magnitude Q on the surface of a semi-infinite soil mass can be estimated by the expression. A point load Q=1500 kN is applied at the ground surface. Evaluate the stress in the soil caused by the point load at a depth of 2.5m directly below the load in kPa. Evaluate the stress at a depth of 2.5m and a horizontal distance of 3m from the point load.
An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40mm in a length of 11 m.Assuming E=200GPa, Determine the total elongation of the bar.
An upright cylindrical water tank having a diameter of 3 meters and a height of 6 meters is to be completely filled with water. Determine the minimum thickness of the tank plate if the stress is limited to 20 MPa.
The column is constructed from high-strength concrete and eight steel reinforcing rods. If thecolumn is subjected to an axial force of 200 kips, determine the average normal stress in theconcrete and in each rod. Each rod has a diameter of 1 in. ?????? = 30,000 ??? and ????????? =4,000 ???.
A hollow metal tube with an inside diameter of 265 centimeters must carry a tensile load of 910kN. Determine the outside diameter of the tube, in meters, if the stress is limited to 171 MPa.
2. The state plane stress in a mass of dense cohesionless sand (c=0) is described by the following stresses: Normal stress on horizontal plane = 300 kPa Normal stress on vertical plane = 100 kPa Shear stress on horizontal and vertical planes = ± 50 kPa Determine by means of the Mohr circle the magnitude and direction of the principal stresses. Is this state of stress safe against failure assuming φ= 20o?
The velocity profile of a viscous liquid flowing over a fixed plate is given by v=0.68yy2(v is the velocity in m/s and y is the distance from the plate in m).i. Calculate the shear stresses at the plate surface and 0.34 m away from the plate(µ=0.9 Ns/m2).ii. Draw the velocity and the shear stress profile of the system.
Refer to Figure 6.31. The circular flexible area is uniformly loaded. Given:q = 320 kN/m2. Determine the vertical stress increase at point A.