Answered: Determine the forces in members CD, CJ,…

Engineering

Civil Engineering

Determine the forces in members CD, CJ, and DJ. M 10' A L B L 6 panels at 6' K C L D L E L H F L L G

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.6.3P

See similar textbooks

Related questions

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: Answer We can calculate Maximum Tensile and Compressive Bending stress using Bending equation σ =…

Q: In a rectangular open channel, 2.0 m wide, water flows at a depth of 0.8 m. It discharges over an…

A: given- width B=2 mdepth y=0.8 mCc=0.612g=4.43H=0.25 m

Q: 1f) A concrete retaining wall is shown in side view below. A form is used to hold the concrete while…

Q: Q.12 Two soil profile are used as backfill defined a retaining wall as shown in figure, where y, is…

A: Given- depth of soil=2 mcohesion c=0unit weights are 18 & 20 kN/m3

Q: For the given state of stress, determine (a) the maximum principle stress (b) the maximum shearing…

Q: A single degree of freedom system of mass 22 kg and stiffness 17 kN/m vibrates freely. If damping in…

A: Given data in question Single degree of freedom Mass Stiffness To find out Cyclic frequency…

Q: Please show clear and complete solutions. Box the final answers. JK CD ← Answer: 0- D M L 10' A L E…

A: Given data in question Truss Dimensions Loads To find out Angle theta

Q: Determine the ground water infiltration rate, ft3/d/ft2, for a new two-lane pavement with the…

Q: Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Q5/ Prove that the theoretical discharge over a sharp crested rectangle weir is: 2 2 theoretical -…

Q: Make a cut through JK, CJ, and CD. The free-body diagram of the section to the right of the cut is…

A: Question

Q: B A 20 kN/m 4 m 4 m Hinge D E T 3 m 5 m

Q: Design a square pad footing with an overall depth of 600mm, cover to the reinforcements 50mm with…

Q: Determine the maximum bending moment for the beam shown below. Use a = 8 ft, b = 12 ft, c = 6 ft,…

A: Given data a = 8 ft b = 12 ft c = 6 ft Ay = 49.8 Kips Dy = 58.2 kips

Q: 1. Determine the magnitude and direction of the resultant of the system of concurrent forces having…

A: Given data

Q: Two large fixed parallel planes are 240 mm apart. The space between the surfaces is filled with oil…

Q: It is desired to transport 20 cfs of water through a rectangular finished concrete (n = 0.012) canal…

Q: The following shaft has a diameter of 60 mm, and it is made of Aluminum (G = 29 GPa). The shear…

A: Given, d=60 mmG=29 GPaτ= 200 MPaFOS=2.5ϕ=3 degree

Q: Q1). The following consecutive readings were taken along a straight line from station (11+090) to…

Q: A W18 x 50 beam is simply supported on 10-in.-thick concrete walls at both ends as shown in the…

Q: A boy weighing 445 N swings on a 2-m long swing. If his horizontal speed at the lowest point is 3…

Q: The surface tension in a soap bubble of 20 mm diameter, when the inside pressure is 2.0 N/m² above…

A: given- dia D=20 mm=0.02 minside pressure P=2 N/mm2

Q: The post is constructed from concrete and six A-36 steel reinforcing rods. Figure 1 of 1 900 kN 250…

A: Given Data ;

Q: Part 4 Use your shear-force and bending-moment diagrams to determine the maximum positive bending…

A: Given data

Q: Disk A rolls without slipping along the ground with an angular velocity of w = 5 rad/s as shown in…

Q: A 300 mm thick, 2.0 m wide footing slab supports a 200 mm thick concrete wall carrying uniform…

Q: art A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional…

A: Given :

Q: Example 3.8. A lever is keyed to a shaft of 100 mm diameter. The width of the key is 12 mm and the…

Q: Trace the characteristic curve of the pipe shown in the Figure below. Data are: total length of pipe…

A: Given, L = 80 m Leq = 40 m

Q: 2. The magnitude of the three forces acting on the plate are F₁ = 100KN, F₂=80kN and F3= 50kN. Solve…

Q: Use cantilver method Calculate for the axial force in kN at member CB a = 40.4 kN, b = 21.7 kN, c =…

A: Cross sectional Area of column is given. We have to find the neutral axis of the group of column…

Q: W1. W2 _A B a a a b b b

A: Given data:

Q: A metallic column is covered through 1 in. Thick (25.4 mm) spray implemented cementitious cloth. The…

Q: 14 Compute the peak runoff, up using др storm event NR CS method for a 50 Sail Arca=0.3906 mile² 50…

Q: 1f) A concrete retaining wall is shown in side view below. A form is used to hold the concrete while…

Q: The free-body diagram of roller C is shown with the truss members assumed to be in tension. AC BC…

Q: A man, 65 kg, descends to the ground with the help of a parachute, 18 kg. The parachute is…

A: given- mass of man m=65 kgparachute mass mp=18 kgdia=2 mdensity d=0.00125 g/cm3

Q: The following consecutive staff readings were taken with level and 5m staff at 70 m interval. The…

Q: The 0.61 x 1.00 m lid ABCD of a storage bin is hinged on side AB and is held open by looping cord…

A: It is given that : Dimension of lid = 0.61X 1.0 m . Tension in the cord is = 75N To find ; The…

Q: 4. A long rectangular open channel that carries 10 m³/s consists of three segments: AB, BC and CD.…

Q: Situation: A reinforced concrete beam is to be designed by the Strength Design Method of the Code…

Q: Q4). The distance between two points on a map is 12 cm and actual distance between them 45 km, if…

Q: Question 3 Determine the capacity of plate! of plate as well as Belts (14) in the below connection…

Q: ! Required information Consider the loading condition shown. Assume that the flexural rigidity El of…

A: Since the Deflection at point B is given and is correct so ; Deflection at B = 0.0013 wL4EI The…

Q: In the standard SCS-CN method of modelling runoff due to daily rainfall, if CN = 75, the runoff…

A: given- SCS-CN methodCN=75one day rainfall=100 mm

Q: A field is in the form of a regular pentagon. If the bearing of side EA is N 43° 18' E, determine…

Q: Determine the determinacy and stability of the beam shown in figure 1. a. statically determinate,…

A: Given data in question Structures To find out Which among the options is correct Note Ds= degree…

Q: Item 3 The three bars are made of A-36 steel and form a pin- connected truss. Figure 1 of 1 5 ft 5…

A: Given :

Q: Horton's infiltration equation was fitted to data from an infiltration test. It was found that the…

A: Given data- Initial infiltration capacity fo=20 mm/hFinal infiltration capacity fc=5 mm/hHorton's…

Q: Two columns 300mmx300mm and 400mmx400mm are loaded by axial and bending forces as shown. They are to…

A: Footing : A footing is constructed with concrete below the ground. A footing is a part of foundation…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

100%

STATICS OF RIGID BODIES
I NEED HELP ASAP. Please read and answer the question correctly. RATE WILL BE GIVEN ACCORDINGLY. THANK YOU

EXACT ANSWER

Note: The tolerance is ± 1 in the third significant digit

This is a by parts question so please answer all possible question.

The free-body diagram of the entire truss is shown. Find the force ly.
A₂
M
A
Answer: ly =
B
L
K
10
L
L
I,
L
E
L
L

Determine the forces in members CD, CJ, and DJ.
M
10'
A
L
B
6 panels at 6'
K
C
L L
D
L
E
L
H
F
G
L L

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A T-beam has the following properties: bf = 820 mm, bw = 250 mm, d = 470 mm, t = 100 mm. f’c = 20.7 MPa, fy = 414 MPa. Determine the required tension steel area when: a.MD = 175 kN-m, ML = 190 kN-m b.Find the maximum design moment so that its tension controlled. (USE c = 3d/8). Tension steel exactly experiences 0.005 strain. hello please answer that question,,thank you God bless
Design the beam to resist the loads shown using WSD Method. Take fc = 9 MPa, fs = 124 MPa, n= 11, bar diameter = 20 mm. Take b = d/2
Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method.
A structural steel member is in the form of tee. bf= 300mm , tf= 100mm, bw= 200mm, d=300, fy= 248 Mpa. Determine the following: a. location of plastic neutral axis from the top of the beam b. plastic section modulus c. plastic moment capacity
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 34-in.-long bronze [E = 14700 ksi, α=α= 8.4 × 10−6/°F] bar with a cross-sectional area of 1.50 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 9000 ksi, α=α= 12.4 × 10−6/°F] bar with a cross-sectional area of 2.00 in.2. Both bars are unstressed before the load P is applied. Assume L1=34 in., L2=48 in., a=36 in., b=44 in., and c=12 in. If a concentrated load of P = 23 kips is applied to the rigid bar at D and the temperature is decreased by 105°F, determine:(a) the normal stresses in bars (1) and (2).(b) the normal strains in bars (1) and (2).(c) the deflection of the rigid bar at point D.
Q5. Joint A is roller and C is pin supportedPlot BMD & SFD
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi, α= 9.4 × 10−6/°F] bar with a cross-sectional area of 1.00 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 9200 ksi, α= 12.6 × 10−6/°F] bar with a cross-sectional area of 2.50 in.2. Both bars are unstressed before the load P is applied. Assume L1=30 in., L2=48 in., a=32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at D and the temperature is decreased by 120°F, determine:(a) the normal stresses in bars (1) and (2).(b) the normal strains in bars (1) and (2).(c) the deflection of the rigid bar at point D. Solve for F2 and F1.Answers: F1 = kips, F2 = kips. Determine the normal stress in each bar. Use positive if tensile, negative if compressive.Answers: σ1= ksi, σ2= ksi. Determine the normal strain in bars (1) and (2). Use positive if tensile, negative if compressive.Answers:…
A 50 mm x 100 mm purlin is used for a roof truss. Spacing of trusses is 3.5 m Weight of roofing sheets is 120 Pa Roof live load is 750 N/m² of roof area and ceiling load is 140 N/m² of roof area Spacing of purlins is 450 mm on centers. Inclination of the top chord is 30° from the horizontal The timber is 80% stress grade yakal. From table, E(yakal)=9780 MPa. Neglect the weight of purlins. 1. Which of the following most nearly gives the total vertical load, in N/m? a. 455 b. 193 c. 270 d. 338 2. Which of the following most nearly gives the maximum bending stress, in MPa? a. 15.6 b. 5 c. 12.5 d. 33.5 3. Which of the following most nearly gives the maximum deflection, in mm? a. 33.5 b. 16.3 c. 47.5 d. 24.8
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 34-in.-long bronze [E = 15000 ksi, α=α= 9.2 × 10−6/°F] bar with a cross-sectional area of 1.75 in.2. Bar (2) is a 42-in.-long aluminum alloy [E = 10300 ksi, α=α= 11.9 × 10−6/°F] bar with a cross-sectional area of 2.25 in.2. Both bars are unstressed before the load P is applied. Assume L1=34 in., L2=42 in., a=30 in., b=42 in., and c=16 in. If a concentrated load of P = 27 kips is applied to the rigid bar at D and the temperature is decreased by 120°F, determine:
A W 360 x 744 is used as a beam to support a concrete floor system. The floor is to carry atotal load of 250 kPa. The beam is simply supported over a span of 6 m. Assume the beamis laterally supported over its length. Use A36 steel with Fy = 250 MPa. Allowabledeflection is L/360.a. Determine the center to center spacing of the beams without exceeding the allowableshear stress.b. Determine the center to center spacing of the beams without exceeding the allowablebending stress.c. Determine the center to center spacing of the beams without exceeding the allowabledeflection.
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
A Wide Flange Built Up beam is supported at both ends by a fixed support and has a length of 6.8m column to column. The flanges (450mmx20mm) are continuously welded to the web (500mmx18mm). The weight of the Built Up beam has a uniform load of 294N/m through-out its length. The brace is installed at both ends of the beam and has a space of 6.8m. The steel used is ASTM36. Determine the allowable bending stress of this beam.