Disk A rolls without slipping along the ground with an angular velocity of w = 5 rad/s as shown in the diagram. Determine the velocity of Collar C at this instant if it is confined to move along 60° inclined slot. Use the Instantaneous Center (IC) method only. Include the free body diagram and step by step solution with detailed explanations. A+ 2 ft B 45⁰ 4.123 ft 30° w = 5 rad/s 60°

Disk A rolls without slipping along the ground with an angular velocity of w = 5 rad/s as shown in the diagram. Determine the velocity of Collar C at this instant if it is confined to move along 60° inclined slot. Use the Instantaneous Center (IC) method only. Include the free body diagram and step by step solution with detailed explanations. A+ 2 ft B 45⁰ 4.123 ft 30° w = 5 rad/s 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Block A is moving down the inclined plane with an initial velocity of vAo = 4 m/s, increasing at a rate of aA = (2t+1)m/s2. Determine the angular velocity (rad/s) of disk D after t=11.9 s.
INSTANT CENTERS Slider D has a velocity of 3 m/s to the right, determine the angular velocity of link AB. 0.4 m 0.4 m 90 45° 45 3 m/s
3) The disk is rotating about point O with an angular velocity w0=7 rad/s in the given direction. Rod CD is attached to the disk of center O and rod AB by hinges. For the given instant, determine the angular velocity @AB of the rod AB and absolute velocity (Ve) of point B. (r= 4m, |CD|=4m, |AD|= 3m, |DB|= 2m, B=30°, 0=60°) D A
Use conjugate beam method to determine the slope at C. Where El=100,000KN/m^2 1OOKN A AAm C RB
5. If link AB is rotating at MAB = 6 rad/s, determine the angular velocities of links BC and CD at the instant e = 30°. 250 mm WAB = 6 rad/s 30 B 300 mm 400 mm D.
3. Calculate the vertical and horizontal displacements as well as the rotation at A. Given: E-200KN/m; IAC le4 cm"; ICD 2e4 cm D 3m 5kN 1m B 2KNT 4m
Use Virtual Work method to solve for the slope at joint F, horizontal deflection at joint at F, and vertical deflection at joint E of the rigid frame shown. 80 KN 3m D 2m E 21 2m I 3m 30KN B21 3m 20KN OF = 1122.5kN.m?/El Ay = 4437.5kN.m³/El (at E) %3D Answer: AH = 1519.17kN.m³/El (at F)
1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. E =210 GPa. 100 | Cross section 6KN.m 2m B8KN 2 kN/m 2m T ) B8KN 2m
(b) Find the rotation at "B" (c) Find the horizontal drift at "C" Given: [W24x94] Properties: E = 29,000 ksi, A = 27.7 in², and I = 2,700 in¹ 25 k 20 ft B 1.2 k/ft 30 ft C 15 ft 15 k 15 ft
Problem 1 Using the analytical method (integration of the differential equation), determine the rotation and deflection a) at end B, b) at mid length of the cantilever beam AB when it is loaded as shown below. EI = 10000 kN-m². 80 kN A B| 100 kNm 4 m
Figure 3 shows a square plate is constrained within the slots at A and B. When θ = 25°. Point A is moving at va = 12m/s. Determine the velocity point D at this instant and the trajectory of the instantaneous center of zero velocity(IC) when the square plate moves from θ = 25° until θ = 0°. When θ = 0°, determine the velocity of point B and point C if the va = 20m/s. Another case, when θ = 25° and the velocity of point A is increase to 14m/s, does the trajectory of IC change? Justify your answer
For the overhanging beam shown, determine the value of Eli0 at point C. Use Virtual Work Method. 1200 N/m 3600 N/m B A C 4 m 2 m