Determine the governing ASD axial load KN for a column in a multisory office building using the nominal axial loads below. Dead load = 347 kNLive load = 169 kNRoof live load = 57 kNEarthquake load = +- 142 kNF1= 1.0 Determine the governing (ASD) axial load (kN) for a column in a multistory office building usingthe nominal axial loads below.Dead load = 347 kN%3DLive load = 169 kN%3DRoof live load = 57 kNEarthquake load = +142 kNfi = 1,0Next

Answered: Image /qna-images/answer/f26918c5-84f0-41a7-8117-9b61fb0c4efd.jpg

Determine the governing (ASD) axial load (kN) for a column in a multistory office building using the nominal axial loads below. Dead load = 347 kN %3D Live load = 169 kN %3D Roof live load = 57 kN Earthquake load = +142 kN fi = 1.0 %3D

Determine the governing (ASD) axial load (kN) for a column in a multistory office building using the nominal axial loads below. Dead load = 347 kN %3D Live load = 169 kN %3D Roof live load = 57 kN Earthquake load = +142 kN fi = 1.0 %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
A column in the upper story of a residential building is subjected to a compressive load from the following sources: dead load = 35 kN, occupancy live load = 4.8 kN, roof live load = 21 kN, and rain load = 22 kN. 1. If load and resistance factor design is used, compute the factored load to be used in the design of the column. Which NSCP load combination controls? a. ?.?(?+?) b. ?.?(? + ? + ?) + ?.?(? + ?) + ?.?(?? ?? ?) c. ?.?? + ?.?(?? ?? ?) + (??? ?? ?.??) d. ?.?? + ?.?? + ??? + ?.?(?? ?? ?) e. ?.?? + ?.?? + ??? f. ?.?? + ?.?? + ?.?? g. ?.?? + ?.?? + ?.?? 2. What is the value of the required design strength of the column in Item 1? 3. What is the required nominal strength of the column in Item 1 for a resistance factor of 0.90? 4. If allowable strength design is used, compute the required load capacity to be used in the design of the column. Which NSCP load combination controls? a. ? + ? b. ? + ? + ? + ? + ? c. ? + ? + ? + (?? ??…
B. Using ASD determine the total service load that the column can carry Round your answer to 3 decimal places.
Calculate the governing load combination for a secondary beam with effective width = 2.0 m Dead load Weight of slab = 3.0 kPa Ceiling services = 1.0 kPa Self-weight of beam = 1.0kN/m Imposed load - 0.2 kPa
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2.0 mon centers, on simple supports over a span of 6.0 m. The floor supports a superimposed servicedead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa,calculate: 7. Factored uniform load on a typical interior beam in KN/m using load factors of 1.2 for dead load and 1.6 forlive load.
Need to consider the live load reduction
A column in the upper story of a building is subjected to a compressive load from the followingsources: dead load = 30.8 kips, occupancy live load = 1.7 kips, roof live load = 18.7 kips, andsnow load = 19.7 kips. Determine the factored load (required strength) to be used in the designof the column. Which load combination controls? What is the required design strength of the column? What is the required nominal strength of the column for a resistance factor of 0.9?
Determine the maximum combined loads using the recommendedAISC expressions for LRFD. D = 9000 lb, L = 5000 lb, Lr = 2500 lb, E = ;6500 lb (Ans. 20,050 lb)
Given the following floor plan of a building as shown in FIGURE ADL= 3.6 kPa, LL = 4.2kPaIf Columns E and H are deleted and beam DEF and GHI rests on beam BEHK. Based on tributary area. 1. Find the load on BEHK at E.a. 140.4 kNb. 266.6 kNc. 210.6 kNd. 152.1 kN2. Find the load on beam BEHK at H.a. 152.1 kNb. 266.6 kNc. 210.6 kNd. 133.7 kN3. Find the maximum moment on beam BEHK. Use Pab²/L². a. 174.4 kNmb. 236.3 kNmc. 273.2 kNmd. 385.8 kNm
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate: Factored uniform load on a typical interior beam in kN/m using load factors of 1.2 for dead load and 1.6 for live load.
Pls solve with FBD’s it’s imperative. Handwritten answers only. The building section associated with the floor plan in Figure P2.3 is shown in Figure P2.7. Assume a live load of 60 lb/ft on all three floors. Calculate the axial forces produced by the live load in column C2 in the third and first stories. Consider any live load reduction if permitted by the ASCE standard.
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a superimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using Pc= 21 MPa, long bar fy = 415 MPa, calculate the following: 1. Factored uniform load on a typical interior beam in kN/m using load factors of 1.2 for dead load and 1.6 for live load. A. 8.928 B. 11.448 C. 11.028 2. Effective flange width of a typical interior beam in mm. D. 4.960 A. 1,500 B. 1,850 C. 1,200 3. D. 1,466 Required amount of 16-mm-flexure bars for a typical interior beam in positive bending. Use 10-mm-dia. stirrups A. 512 mm2 B. 246 mm? C. 331 mm? D. 427 mm2