The mechanical efficiency of the pump is 0.85 and pumping with a rate of 650 gal/min of engine oil at 100° with the following properties: specific gravity of 0.883 and kinematic viscosity 21.9x10-6. The 6-in and 4-in Schedule 40 pipe has an area of 0.2006 ft² and 0.0884 ft², respectively. Determine the power added by the pump. Flow Pump 6-in Schedule 40 4-in Schedule 40 | 4 in Engine Oil 30 in Mercury (sg =13.54)

The mechanical efficiency of the pump is 0.85 and pumping with a rate of 650 gal/min of engine oil at 100° with the following properties: specific gravity of 0.883 and kinematic viscosity 21.9x10-6. The 6-in and 4-in Schedule 40 pipe has an area of 0.2006 ft² and 0.0884 ft², respectively. Determine the power added by the pump. Flow Pump 6-in Schedule 40 4-in Schedule 40 | 4 in Engine Oil 30 in Mercury (sg =13.54)

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter13: Energy And Power

Section: Chapter Questions

Problem 3P: An elevator has a rated capacity of 2200 lb. It can transport people at the rated capacity between...

See similar textbooks

Similar questions

Calculate the required pipe diameter to avoid cavitation, if the pump deliversQ = 30US gallon/min water from a closed tank, where the pressure (above thewater level) is p = 40kPa. The equivalent length of the smoothened concretepipe on the suction side is 12m while the suction flange of the pump is 8m belowthe water level. The vapour pressure at the given water temperature is 2.8kPa.The required net positive suction head is NPSHr = 3.2m. Please show complete formulas and units being cancelled.
If the flow of 0.10 m3/s of water (mu = 1.31 x 10-3 Pa.s) is to be maintained in the system shown, what power must be added to the water by the pump? The pipe is made of steel and is 15 cm in diameter. Neglect minor losses. TV
The energy loss between points 1 and 2 is 3.40 lb-ft/lb and the pump delivers 40 gal/min of fluid having a specific weight of 60.0 lb/ft3. What is the required hp of the pump? The inside diameter for the 2-in and 3-in schedule 40 steel pipes are 2.067 inches and 3.068 inches respectively
Waters enter a pump through a 25 cm. dia. Pipe at 35Kpa. It leaves the pump at 140 kPa through a 15 cm. dia. pipe. If the flow rate is 150 li/sec., find the horsepower delivered to the water by the pump. Assume suction & discharge sides of pump are the same elevation.
Water is pumped through a vertical 2-in new galvanized -iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 200lb per sq in. What pressure can be expected at a point in the pipe 250 ft above the pump when the flow is 150 gpm?
For water supply of a town, water is pumped from a river 4km away into a reservoir. The maximum level difference of river and reservoir is 20m. Town population is 50,000 and per capita water demand is 120 lpcd. If the pumps operate for a total of 8hrs and pump efficiency is 60%, calculate pump B.H.P Assume friction factor as 0.0075 and pipe velocity as 2m/s and maximum daily demand as 1.6 times avg. daily demand.
discharge through pipe is 10m3/sec.and total head is 100 ft.calculate unit power of pump?
A tank filled with water at 30°C is supplies water for a shower based on gravity driven flow. The system includes 20 m of 1.5-cm-diameter galvanized iron piping with four 90° miter bends without vanes and a wide-open globe valve. The entrance to the pipe from the tank is square-edged, and the showerhead has an exit loss coefficient of 0.5. If water is to flow at a rate of 0.7 L/s through the showerhead, determine how high the water level in the tank must be above the exit level of the shower to meet the flow requirement.
The parallel galvanized-iron pipe system delivers water with a total flow rate of 0.036 m3/s. If the pump is wide open and not running, with a loss coefficient K = 1.5, determine the flow rate in each pipe. Use f1 = 0.0264 and f2 = 0.0282. Choices: Q1 = 0.013 m3/s and Q2 = 0.023 m3/s Q1 = 0.023 m3/s and Q2 = 0.013 m3/s Q1 = 0.021 m3/s and Q2 = 0.015 m3/s Q1 = 0.015 m3/s and Q2 = 0.021 m3/s None of the choices
1. A centrifugal fan supplies 4.7m3 / s of air at a total static pressure of 325Pa. If the fan efficiency is% 60 and rotates at a speed of 950rpm and supplies air with a velocity of 12m / s, determine the fan total pressure, air power, and fan power? Ans. 411 Pa 2. If the efficiency of the fan given in Problem - 1 becomes 70%, determine the power required for running it. Then, find the power required and airflow rate supplied if the fan speed is increased to 1050rpm. Also, assume that the fan static pressure does not change and determine the air velocity out of the fan. Ans. 4.6kW, 6.21kW, 5.195m3 / s, 17.2m /
A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gases near the pump at the entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.Answer: 10.7 hp, 2.4 ft
The discharge through pump 10m^3 per second and total head is 100 ft. Find unit power of pump