Determine the magnitude of F2 which will cause the reaction Cy at the bearing C to be equal to zero. The bearings are in proper alignment and exert only force reactions on the rod. Set F1 = 400 lb.

Q: Determine the magnitude of F1 for equilibrium of the particle.

A:

Q: Determine the weights W for which the 100 Ib block is in equilibrium. H 0.30 H = 0.25 100 lb 20

A: For a system  to be in equilibrium, the net external force and torque on the body should be zero. To…

Q: Two forces F1 150 N and F2 50 N to hold the weight of 200 N. Check and determine if the body is in…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: Where must the 2.2 kN force be applied so that the bar A whose mass is negligible will be in…

A:

Q: If block D weighs 300 lb and block B weighs 275 lb. determine the required weight of block C and the…

A: Consider the free body diagram: For block D: T1=275 lbAngle between forces T1 and T2=αAngle between…

Q: Determine the vertical force P that must be applied at ABC to maintain the equilibrium of the…

A: Draw the displacement diagram. The displacement in A, D, E are downward and the displacement in C,…

Q: Q5 The three cables are used to support the 30-kg flowerpot, as shown in the Figure 9. Determine the…

A: Given: M = 30 kg and three cables To find : force in each cables

Q: If the weight of the boom is negligible compared with the applied 29-kN load, determine the cable…

A:

Q: If the mass of the bar OB is negligible compared to the mass of the suspended object E, the bar…

A:

Q: Q2/ Determine the unstretched length of spring AC if a force P 801b causes the angle 0 = 60° for…

A: Solution:

Q: Q3. The lamp has a weight of (20 40 N) and is supported by the six cords connected together as…

A:

Q: 1.If cable CB is subjected to a tension that is twice that of cable CA, determine the angle 0 for…

A:

Q: If the load has a weight of 200 lb, determine the x, y, z components of reaction at the…

A:

Q: Determine the magnitude of the pin reaction at A and the magnitude and direction of the force…

A: Given Data All dimentions are modified into the 1.1 m The mass of the object is modified into 175 kg…

Q: 1m DS

A:

Q: Q 3: Determine the maximum weight of the engine that can be supported without exceeding a tension of…

A:

Q: The 50-kg pot is supported from A by the three cables. Determine the force acting in each cable for…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 675 lb, a = 2.7 ft, b = 2.0 ft, r = 9 in.…

A:

Q: The wall-mounted 3kg light fixture has its mass centre at G. Determine the vector reactions at A.…

A:

Q: The bent rod is supported at A, B, and C by smooth journal bearings. Determine the magnitude of F2…

A: As per given figWe have F1=-687cos 45°j^-687sin 45°k^F1=(-485.78 j^ -485.78 k^)F2=F2cos 45°sin 30°…

Q: The ramp of a ship has a weight of F Ib acts in the center of gravity at G. The ramp is supported by…

A:

Q: The 10-lb weight is supported by the cord AC and roller and by a spring. If the spring has an…

A:

Q: If the maximum tension either rope can sustain without breaking is 4700 N, determine the maximum…

A: Given Data: The maximum tension in both the ropes is, Tmax=4700 N.

Q: If the bucket weights 50 lb, determine the tension developed in each of the wires

A:

Q: If cylinder E has a mass of 20 kg and each cable segment can sustain a maximum tension of 400 N,…

A:

Q: Two forces F1 150 N and F2 50 N to hold the weight of 200 N. Check and determine if the body is in…

A: Given data, Force F1 = 150 N and, F2 = 50 N Force F1 in vector form, F→1= F1-sin45i^+cos45j^ F→1 =…

Q: The 0.5 m long rods AC and BD are made of Aluminum and each has a cross- sectional area of 200 mm2…

A:

Q: The ring weighs 6 lbf and is in equilibrium. The force F1 = 4.5 lbf. Determine the force F2 and the…

A: As per given question  Force f1=4.5 lbf And angle =30° We have to determine force f2 and angle α

Q: If cable CB is subjected to a tension that is twice that of cable CA, determine the angle @ for…

A: Tension in CB = 2* Tension in CA

Q: Q1. The members of a truss are pin connected at joint O. Determine the magnitudes of F1 and F2 for…

A: Given Data : Joint O Members of truss

Q: Determine the magnitude of each of the reactions at the supports; roller at A and pin at B. 0 = 30…

A:

Q: Determine the unstretched length of spring AC if a force P = 100 Ib causes the angle 0= 52° for…

A:

Q: 10. Determine the horizontal component of the reaction force at the hinge support A as shown to…

A:

Q: The beam is subjected to the two concentrated loads. Assuming that the foundation exerts a linearly…

A:

Q: problem r1

A:

Q: The jib crane is pin connected at A and supported by a smooth collar at B. If x = 8 ft, determine…

A: Given data :  (jib crane)x = 8 ftAB= 12 ftw = 5000 lbpin connected at Asmooth collar at BTo find…

Q: Q/ The eyebolt supports the four forces shown. If the net effect on the bolt is a direct pull of 3…

A:

Q: If the beam AB is supported by rocker at A and pin at B, determine the vertical component of the…

A:

Q: Q/. Determine the force in the cable BC and the stretch of the spring for equilibrium. 650 N k - 200…

A:

Q: Determine the magnitude of the force P required to hold the 300-kg crate in equilibrium

A:

Q: 10. The lamp has a mass of 15kg and is supported by a pole AO and Cables AB and AC. If the force in…

A:

Q: The object below is in equilibrium and has a weight w = 80 N. Find T,, T2, T3 and T4. 55 TA T3…

A: Given: The weight, W = 80 N

Q: Please help.

A: Drawing the free body diagram of the system,

Q: Determine the magnitude of the pin force at A. Assume W = 615 lb, a = 3.2 ft, b = 2.3 ft, r = 9 in.

A:

Q: Determine the force in cable BC and the spring stiffness (k) in N /m when the spring is held in the…

A: Force in the spring, FAB=kxx=deflection in springk=stiffness of the springFAB=Force in the…

Q: the gusset plate is subjected to the forces of four members. Determine the force in member B and its…

A:

Q: 3. The members of a truss are connected to the gusset plate. If the forces are concurrent at point…

A: For concurrent forces are to be in equilibrium 1. Sum of horizontal components are zero 2. Sum of…

Q: F1 α 30°

A: Let W = Weight of ring =5N F1 =4.5N By using law of equilibrium  ΣFx = 0 F1cos30° - F2cosα =0…

Q: The uniform crate has a weight of 200 lb acting through point G. What magnitude of force P is…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.