Determine the magnitude of the horizontal reaction (N) at A if P = 229 N and Q = 1966 N. Let x = 2.55 m, y = 2.42 m, and z = 2.01 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left. Q y A B A D y dat E X C ...

Determine the magnitude of the horizontal reaction (N) at A if P = 229 N and Q = 1966 N. Let x = 2.55 m, y = 2.42 m, and z = 2.01 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left. Q y A B A D y dat E X C ...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure given below, determine the vertical reaction at points A, C, and E.
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Where: Q=2 T=6
The forces acting on a 1-m length of a dam is shown in the Figure. The upward ground reaction varies uniformly from an intensity of p1 kN/m to p2 kN/m at B. Determine the P1 and P2 and the horizontal resistance to sliding.
Determine the magnitude of the horizontal reaction (N) at A if P = 254 N and Q = 2395 N. Let x = 2.48 m, y = 2.5 m, and z = 2.05 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left.
Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.
Determine the vertical distance of the center of gravity of the curved gate from the water surface shown in the figure. The curved gate is 5.7 m long. The values of the vertical component (Fv) and the resultant force. (F) acting on the gate are 300 kN and 400 kN asap
For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. a = 3.9 m, b = 9 kN/m, c = 15 kN.
Determine the force in the hydraulic cylinder EF that would maintain theparallelogram mechanism in the position shown.
To loosen a frozen valve, a force F of magnitude 90 lb is applied to the handle of the valve. Knowing that θ = 25° and the moments about the coordinate axes are Mx = −61 lb⋅ft and Mz = −43 lb⋅ft, determine Φ and d.
In the figure provided below: determine the vertical reaction at Point B and E.
For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax?
Situation 1– Two spheres 1.20m in diameter are connected by a means of a short rope. One weighs 4kN, while the other weighs 12kN. When placed in water, 1. Determine The buoyant force acting on the heavier sphere in kN 2. The tension in the rope in kN 3. The depth of submergence of the 4kN sphere in meter.