determine the minimum applied force P required to move wedge A to the right. the spring is compressed a distance of 170mm. Neglect the weight of A and B. the coefficient of static friction for all contacting surfaces is U=0.35. Neglect friction at the rollers.

determine the minimum applied force P required to move wedge A to the right. the spring is compressed a distance of 170mm. Neglect the weight of A and B. the coefficient of static friction for all contacting surfaces is U=0.35. Neglect friction at the rollers.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The best method of interpolation of contours, is by Graphical means all the above O O O O O…

A: To determine the best method of interpolation of contour.

Q: 43.8 kN/m RA= Bx= -3 m 時 A kN kN 29.2 kN/m -6 m By= B -3 m 133.5 kN 81 kN 81.4 kN m

Q: The reduced level of a floor is 99.9 m, the staff reading on the floor 1.505 m. If the inverted…

Q: A solid shaft of 150 mm radius is used to transmit torque. Find the maximum torque transmitted by…

Q: Q-A hydraulic turbine develops 8000 kW when running at 300 rpm under a head of 45 m. find the speed…

A: Given- Power P=8000 kW, Speed N1=300 RPM, Head H1=45 m, Head H2=60 m,

Q: Use the double integration method to deter beam. El is constant at E = 200 GPa, I= 4000

Q: The table below contains the information about two embankment sections. The distance between them…

A: To find volume using trapezoidal formula

Q: The state of stress at a given point in a material component is = 120 MPa ; 0₁= The loading on the…

Q: The sequent depth ratio of a hydraulic jump in a rectangular horizontal channel is 10.30. The Froude…

Q: Problem-5 A partially open sluice gate discharges water at 6 m/s with a depth of 40 cm in a…

A: Given data- Velocity V=6 m/s, Depth y1=40 cm=0.40 m, Width B=5 m, g=10 m/s2. To Find- Post jump…

Q: 4-Classify the following soils using the USCS including Group Symbol and Group Name: Soil % passing…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: * In levelling operation If second reading is more than first, it represents a rise If first reading…

A: In surveying levelling is done to measure the elevation of different points or survey line on the…

Q: Q- In a single-acting reciprocating pump, the acceleration head at the beginning of the suction…

A: Given, Hatm= 10m Suction head created by pump= -3.5m

Q: Determine all force of the member Fig. A 3 Noten: Tension force (-) [T] Compression force (+) [C] 6m…

A: To Determine :- Forces in each memeber of the truss given. Sign convention : Tension ( - )…

Q: Convert 60 mi/hr to an equivalent number of ft/s. Show your calculations

A: For an approximate result multiply the speed value by 1.467 So, 60*1.467 = 88.02 ft/s.

Q: A triangular lot has an area of a quarter of. lot have also the following shown below. length (51…

Q: 2. 20 g/l solution of a chemical tracer was discharged into a stream @ 0.01 l/s. At sufficiently far…

Q: A В D 400 mm, 625 mm 1. The aluminum rod, AB (G = 27 GPa), is bonded to a brass rod BD (G = 39 GPa)…

A: Given:- The modulus of rigidity of aluminum rod AB = 27 GPa The modulus of rigidity of brass rod BD…

Q: Problem An aeroplane is flying at an altitude of 5000 m. Calculate the pressure around the…

A: Given Height Z=5000 m, Lapse rate L=dTdZ=-0.00650K/m, Pressure at ground level p0=10.143…

Q: The hydraulic jack in the figure is filled with two types of oil, the specific gravity of oil 2 is…

A: Given, γoil 2 = 0.80 γoil1 F1 = 2000 lbf

Q: many futuristic projection system types, together with their parts and purposes What are they…

A: In order to aid navigators at sea and on land, maps have been created of the trade routes, local…

Q: A reservoir with a live storage of 300 million cubic metre irrigate 40000 hectares (1 hecatre = 104…

A: Given a reservoir with, Live storage = 300 Mm3 Crop area, A = 40000 hectares. Base period = 120 days

Q: T 2 m 3 kN 2 m G LEX -3 m -1.5 m- (b) *Assume A to be hinged and D to be roller. 6 kN F 3 m- -3 m- 3…

A: To Determine :- The support reactions and member forces on the truss.

Q: an axially loaded column is of 300mm x 300mm size. the effective length of the column is 3m, what is…

Q: 4. A saturated soil has the following chraracteristics: initial volume = 19.65 cu. Cm final volume =…

Q: 2. Discuss how structural steel is tested in the aboratoryforquality contro. Cite relevant ASTM…

A: Different tests, including destructive as well as nondestructive, are carried out to describe the…

Q: ,0),B (170, 32 0), E (-40, -220

Q: (Situation 1) Determine the support reactions on the following structures: (a) cont -6 ft- 5k/tt -12…

A: A loaded beam is given and it has been asked to determine support reactions. Please refer step 2 for…

Q: Q4: A. Calculate the pressure of steam at a temperature of 500°C and a density of 24 kg/m³ using (a)…

Q: If + 0.8% grade meets - 0.7% grade and the rate of change of grade for 30 m distance is 0.05, the…

A: g2 = -0.7% g1 = 0.8% Rate of change of grade r= 0.05/30 = 0.00167

Q: 112. Determine the cross-sectional areas of members AG, BC, and CE for the truss shown in Fig.…

A: Degree of static indeterminacy, Ds = m+r-2j m = number of members r = number of unknown reactions j…

Q: 6 kN/m 4 m B 3 m *Assume A and C to be hinged supports, and B to be a pinned connection.

Q: The cable will fail when subjected to a tension of T = 6 kN. Figure 1) gure 0.1'm -0.75 m- ... * 0.5…

A: Reference : Mechanics, Tension in pulley and cable. Given : A Tension T = 6 KN P force acting…

Q: In surveying, why is it important to know the individual's pace factor?

A: To answer - Importance of knowing the individual's pace factor.

Q: P.T, P.I, P.C are the basic requirements for setting a Vertical . curve True O False O

A: There are two different types of curves in the highways. The vertical curve is one of them. To…

Q: locate a missing point on the ground: a. You need at least three reference points b. You need at…

A: Given To locate a missing point on the ground:

Q: In simple circular curve, the angle between fore tangent and back tangent is known as All of above…

A: Asked: Angle between fore tangent and back tangent in a simple curve is called

Q: The coordinates of traverse stations of a closed traverse ABCDE are given i table Calculate the area…

A: Using formula

Q: ! 4.2. A 16 ft wide sand bed stream (Sf=0.002, n'= 0.015, with smooth channel banks) has the…

Q: An embankment for a highway 30 m wide and 1.5 m in compacted thickness is to be constructed from…

Q: St. No. A B C D E F The table below is the page of a level field book. 1) Calculate the difference…

Q: At the point of operation with maximum efficiency, a turbine indicated unit power of 12 units and…

A: Given- Unit power-Pu=12,Unit speed-Nu=98,Design head H=8.5 m. It is needed to find the speed and…

Q: St. No. A B C D field book. 1) Calculate the difference in level between point A and G. 2) If it is…

A: To find difference in elevation between A and G Depth of fill at D

Q: Problem For the frame shown, design the maximum permissible value of P with a factor of safety of…

Q: 16 ft wide sand bed stream (Sf = 0.002, n' = 0.015, with smooth channel banks) has the following…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: What is the shear strength reduction factor, ϕ, for a beam with tied transverse reinforcement and…

A: To find shear strength reduction factor

Q: contaminated water to reach to Reservoir 2 will be

A: Given, Two reservoirs are connected through a homogenous and isotropic aquifer having hydraulic…

Q: 11. For the truss shown in Fig. P-111, calculate the stresses in members CE, L DF. The…

A: To find stress in DE,DF,CE

Q: A highway designed for 80 km/h speed has a horizontal curve section with radius 250 m. If the design…

A: Speed of vehicle and radius of horizontal curve is given and it has been asked to determine required…

Concept explainers

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.

Question

determine the minimum applied force P required to move
wedge A to the right. the spring is compressed a distance of
170mm. Neglect the weight of A and B. the coefficient of
static friction for all contacting surfaces is U=0.35. Neglect
friction at the rollers.
k= 15 kN/m
P
A
B
10°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cylinder weighs 10 lb and is held in equilibrium by the belt and wall. If slipping does not occur at the wall, determine the minimum vertical force P which must be applied to the belt for equilibrium. The coefficient of staticfriction between the belt and the cylinder is μs = 0.25.
determine the moment (m-kN) about point A due to the 3 kN and the two 17 kN forces.
For the truss in Figure P8.3, compute the horizon-tal and vertical components of the displacement of jointC. The area of all bars = 2500 mm2, and E = 200 GPa.
Determine the forces and moments at point C and point D For the SN kn/m the given is 66 kn/m
(a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For all bars, area = 2400 mm2 and E = 200 GPa. (b) Assuming that no load acts, determine the horizontal displacement of joint B if support A moves 20 mm to the right and 30 mm down and support E moves downward 36 mm.
Calculate the moment of force of 1.4 kN with respect to points P1 and P2.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is μs = 0.2.
Determine the reactions and the expected horizontal displacement at point D by applying 1 unit load at D directed to the right.
Use Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine the following: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
Determine the Horizontal and Vertical Force Reaction at Point B.
Determine the Force Frequired to hold the bar AB in a horizontal position on the smooth inclines shown in figure below. Also determine the reactions at A and B 1.2m, 4.2m, 0.6m A 60 degrees and 45 degrees B 90N
Determine the slope at B and the displacement of B due to the horizontal Load (Yhb)