The cable will fail when subjected to a tension of T = 6 kN. Figure 1) gure 0.1'm -0.75 m- ... * 0.5 m -0.75 m- C -0.75 m- A < 1 of 1 > Submit No= Value ▼ Part C O Submit μÀ ▼ Part D X Incorrect; Try Again; 4 attempts remaining Check your signs. Vc = Value Mc= Previous Answers Request Answer Calculate the shear force at a section passing through point C for this loading. Express your answer to three significant figures and include the appropriate units. μÅ O DA Request Answer KN 1 HÅ Value BMC Calculate the moment at a section passing through point C for this loading. Express your answer to three significant figures and include the appropriate units. 1 Units ? Units ? www ?

The cable will fail when subjected to a tension of T = 6 kN. Figure 1) gure 0.1'm -0.75 m- ... * 0.5 m -0.75 m- C -0.75 m- A < 1 of 1 > Submit No= Value ▼ Part C O Submit μÀ ▼ Part D X Incorrect; Try Again; 4 attempts remaining Check your signs. Vc = Value Mc= Previous Answers Request Answer Calculate the shear force at a section passing through point C for this loading. Express your answer to three significant figures and include the appropriate units. μÅ O DA Request Answer KN 1 HÅ Value BMC Calculate the moment at a section passing through point C for this loading. Express your answer to three significant figures and include the appropriate units. 1 Units ? Units ? www ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the given flexible cable set-up carrying a uniformly distributed load spreadhorizontally has a magnitude of 6.5 KN/m. Fill-up the table below for the required data. Given the followingmaterials specification, fy (cable) = 415 MPa, fc' (concr’te) = 24 MPa, γconcrete = 23.5 KN/m3 Determine the Maximum Tension in The Cable = ____________________ KN.  Given the capacity of the cable, determine it’s diameter = _____________mm For the square post at A , what will be it’s theoretical dimensions, x = _______________mm What will be the total Volume of the concrete at B to serve as dead man’s load = ___________m3
A steel plate weighing 27 kN is hoisted by a cable sling that has a clevis at each end. The pins through the cle- vises are 22 mm in diameter. Each half of the cable is at an angle of 35° to the vertical. The average shear stress in each pin is approximately: (A) 22 MPa (B) 28 MPa (C) 40 MPa (D) 48 MPa
1. Cable carries uniform 20 kN/m for entire length. What is the value of a? 2. Tension of cable at A in kN. 3. Tension of cable at C in kN.
Please present FBD/s A steel cable with nominal diamter of 25 mm is used in a consturction yard to lift a bridge section weighing 50kN. Modulus of Elasticity of cable is 10GPa. If the cable is 15m long, how much will it stretch when the load is picked up?
Calculate the working stress on the 1/2-inch diameter cable as shown on the figure below. The bar has a uniformly weight of 66 lbs. FN = 78kips
3. A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 KN, what is the value of the sag "h"?
For the cable shown below,Determine the tension segment CD in kNDetermine the tension segment AB in kNWhat is the value of h?
knowing that the tension in cable AC is TAC =369N, determine the y-component of TAC. Round off only the final answer expressed in 3 decimals
The triangular trough is hinged at A and held together by cable BC at the top as shown. It retains a liquid having specific gravity of 0.826. If the width of the trough perpendicular to the paper is 3 meters, what is the tension in the cable (in kN)? Use a = 3 meters, b = 6 meters., θ = 90°. Round off to three decimal places. There is an Uploaded reference photo on how to solve. Please help.
Show your compete solution. Draw all necessary FBDs (draw the FBDs neatly and clearly labelled. A cable supports a load of 50 kg/m uniformly distributed along the horizontal and is suspended from the two fixed points A and B located as shown. a) Calculate the cable tensions at A and B. b) Determine the length of the cable.
The spike shown needs to be removed horizontally but an obstruction at A prevents direct access. Thus, 2 cables are provided with their lines of action shown as forces P and 1.6kN. Determine force P to ensure that the resultant R is directed along the spike. Also, compute the resultant. Show solution where answer is P = 2.15 kN & R = 3.2 kN
Two cables A and B had their both ends attached to each other as shown.Cable A is 10 in long and cable B is 0.5 in longer than cable A; hence makingcable B slack. The diameter of cable A is 0.70 in. while cable B has a diameter of0.25 in. Find the stresses for both cables if the system supports a downwardforce P = 0.15kip. Use E = 50ksi.