Determine the minimum length of a vertical curve between a -1.78% grade and a -7.8% grade for a road with a 110 km/h design speed. The vehicle approaches the curve from the side of -1.78% grade. The vertical curve must provide the sufficient stopping sight distance and meet the appearance criteria. For stopping sight distance the both vehicle and object are located within the vertical curve. Consider a new road with a single carriageway in each direction, Rt=2.5s, d=0.29, h1=1.1m, h2=0.2m, height of headlight = 0.65m and q=1 degree.

Determine the minimum length of a vertical curve between a -1.78% grade and a -7.8% grade for a road with a 110 km/h design speed. The vehicle approaches the curve from the side of -1.78% grade. The vertical curve must provide the sufficient stopping sight distance and meet the appearance criteria. For stopping sight distance the both vehicle and object are located within the vertical curve. Consider a new road with a single carriageway in each direction, Rt=2.5s, d=0.29, h1=1.1m, h2=0.2m, height of headlight = 0.65m and q=1 degree.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

Compute the minimum length of vertical curve to provide stopping sight distance for a design speed of 100 km/h at the intersection of a +1.4% grade with a -0.6% grade.
Determine the minimum length of a vertical curve between a +1.48% grade and a +6.2% grade for a road with a 100 km/h design speed. The vehicle approaches the curve from the side of +1.48% grade. The vertical curve must provide the sufficient stopping sight distance and meet the appearance criteria. For stopping sight distance the both vehicle and object are located within the vertical curve. Consider a new road with a single carriageway in each direction, Rt=2.0s, d=0.36, h1=1.1m, h2=0.2m, height of headlight,h = 0.65m and q=1 degree.
A horizontal curve on a two-lane highway is designed with a 610-m radius, 3.5-m lanes, and 80 kph design speed. Determine the distance that must be cleared from the inside edge of the inner lane to provide sufficient stopping sight distance. (Note: Curve radius is typically reckoned from the centerline of the roadway, and driver location is assumed to be at the middle of the travelled lane.) Assume coefficient of friction as 0.35. ANSWER M =4.0 ?
A curve of 100 m radius (e=8.0 % and fs=0.14) is located at a section of an existing rural highway which restricts the safe speed to 55 % of the design speed causing a high accident rate. To reduce the accident rate, a new curve is to be designed. Determine the minimum radius of this curve if the safe speed should be increased to the design speed. Assume the same values of e and fs.
A vertical curve is to be designed to connect a -4% grade to a +1% grade on a facility with a design speed of 70 mi/h. For economic reasons, a minimum-length curve will be provided. A driver-reaction time of 2.5 seconds may be used in sight distance determinations. The V.P.I. of the curve is at station 5,100 + 22 and has an elevation of 1,285 ft. find the station and elevation of the V.P.C. and V.P.T., the high point of the curve, and at 100-ft intervals along the curve.
Determine the minimum radius of a horizontal curve required for a highway if the design speed is 70 mi/h and the superelevation rate is 0.08.
A curve of radius 250 ft and e 0.08 is located at a section of an existing rural highway, which restricts the safe speed at this section of the highway to 50% of the design speed. This drastic reduction of safe speed resulted in a high crash rate at this section. To reduce the crash rate, a new alignment is to be designed with a horizontal curve. Determine the minimum radius of this curve if the safe speed should be increased to the design speed of the highway. Assume fs= 0.17 for the existing curve, and the new curve is to be designed with e = 0.08
A curve of radius 250 ft and e = 0.08 is located at a section of an existing rural highway, which restricts the safe speed at this section of the highway to 50% of the design speed. This drastic reduction of safe speed resulted in a high accident rate at this section. To reduce the accident rate, a new alignment is to be designed with a horizontal curve. Determine the minimum radius of this curve if the safe speed should be increased to the design speed of the highway. Assume fs = 0.17 for the existing curve, and the new curve is to be designed with e = 0.08.
A highway reconstruction project is being undertaken to reduce crash rates. The reconstruction involves a major realignment of the highway such that a design speed of 100km/h attained. At one point on the highway, a 245m equal-tangent crest vertical curve exists. Measurements show that at 0+107.3 stations from the PVC, the vertical curve offset is 1 meter. Assess the adequacy of this existing curve in light of the reconstruction design speed of 100km/h and if the existing curve is inadequate, compute a satisifactory curve length.
The minimum simple curve radius you recommended for a highway with design speed (96) Km/hr , super elevation (5.50) percent and f = 0.11, is
A curve of radius 76 m and e = 0.08 is located at a section of an existing rural highway, which restricts the safe speed at this section of the highway to 50% of the design speed. This drastic reduction of safe speed resulted in a high crash rate at this section. To reduce the crash rate, a new alignment is to be designed with a horizontal curve. Determine the minimum radius of this curve if the safe speed should be increased to the design speed of the highway. Assume fs = 0.17 for the existing curve. The new curve is to be designed with the same superelevation
A vertical curve is going to be designed to join a 0% grade with a +5% grade at a section of a highway. The station and elevation of the PVC point are 5+00 and 12 ft, respectively. Assuming AASHTO design standard values for perception-reaction time, deceleration rate for braking, and driver’s eye and object heights, determine the following: 1. The min length of the curve if the design speed is 65 mi/h. 2. The station and elevation of the PVT. 3. The station and elevation of the high or low point. 4. The elevation of the point at station 6+50.