Answered: Determine the outer diameter (mm) of a…

Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Related questions

Q: 1. Two streams of water are mixed steadily as shown in the figure below. Find the exit velocity if…

A: Given data: Volumetric flow rate of stream 1, V1 = 0.06 m3/s Mass flow rate of stream 2, m2 = 70…

Q: Steel railroad reels 15 m long are laid with a clearance of 5 mm at a temperature Ti = 34 °C. Assume…

A: Given: Length of railroad reel (L) = 15 m, Clarence (c) = 5mm = 0.005 m, Ti = 34 °C, Assume, α =…

Q: The runner in a turbine is 70 cm in diameter. The wheel develops 410 kW when turning at 600 rpm…

A: Given: Runner diameter, d = 70 cm Power developed, P = 410 kW Rotational speed, N = 600 rpm Head, H…

Q: Suppose that the regenerative heat exchanger is only 80% efficient, i.e., only 80% of the heat…

A: The given sterling cycle can be represented in P-V diagram as below.

Q: A closed system has water initially as saturated steam at 1.5 bar. Heat is extracted at constant…

A: To solve this problem, we need to use the steam tables to determine the properties of water at the…

Q: Determine the tension in the cable and the horizontal and vertical components of reaction of the pin…

Q: P2-27) Sketch the front, top and right side views of the following object. Use the grid provided. Do

A: According to the given data A 3D object is given We need to find Three projection view of the…

Q: The characteristics of a centrifugal pump operating at 1000 rpm is given by H-45-2100². The system…

A: Givenpump-H=45-210Q2 when operating at 1000rpmsystem-H=28+320Q2The validity of the pump simmilarity…

Q: 3. Consider a reversible, isothermal expansion and a free expansion for a system. The system mass is…

A: DISCLAIMER FOR MULTIPARTSince you have posted a question with multiple sub-parts, we will solve…

Q: Suppose you have a turning operation using a tool with a zero back rake and 5° end relief. The…

A: To find: The diameter of the workpiece grown (increased) due to this flank wear, Given: The back…

Q: Aluminum bars AB and AC have diameters of 10 and 8 mm respectively. Determine the maximum load P…

Q: Why do dna replication and rna transcription are always non equilibrium steady state?

A: This question is based on the application of equilibrium steady state.

Q: Determine the hourly loss of heat from a bare vertical steam pipe whose diameter d = 150 mm and the…

Q: The 1.5 Mg car increases its speed uniformly from rest to 36 m/s in 8 s up the inclined road.…

A: Givenm=1.5Mg=1500 kgV=36m/s uniformalyt=8sε=0.42

Q: When the blocks are released, determine their acceleration, the tension of the cable, and also the…

A: Givent=1.5smA=10 kgm=25 kg

Q: Air at 50 Kpa, 300 K, and Mach 2.0 passes through a normal shock. Determine: a) Total temperature…

Q: What is the Machine Aesthetics? O design that has cognitive, not aesthetic value O aesthetics not…

A: Machine aesthetics refers to the aesthetic style that emerged in the early 20th century,…

Q: For the given vectors V₁ and V₂, determine V₁ + V₂. V₁ + V₂ V₁ V₂ V₁ V₂ V₁ V₂. Consider the vectors…

Q: A bending moment of 216 Nm is applied to a bone with an outside radius of 2.5 cm and an inside…

Q: 4. A concrete weight of 125 kg is released from standstill and a log of mass 200 kg is moved along…

Q: Replace the three forces shown by an equivalent force-couple system at point A. If the forces are…

A: According to the given data A loading structure with three forces We need to find Equivalent…

Q: 9 kmol of oxygen (O₂) gas undergoes a process in a closed system from p₁ = 50 bar, T₁ = 170 K to P₂…

Q: Problem 7: Answer the following conceptual questions: (No calculations necessary) a. What are two of…

A: a. Two benefits of using quaternions when simulating systems are: Quaternions do not suffer from…

Q: Due to three forces F₁, F2 and F3 applied perpendicular a beam is displaced, as indicated in the…

A: Given: To find: Displacements y1, y2, y3

Q: If the air temperature at 18:00h is 8 C, and the air adjacent to the surface has a relative humidity…

Q: A steel drum of a lifting machine has a mass of 25 kg, 2.4 m in diameter and 0.20 adius of gyration.…

Q: A typhoon weakened the streetlight's foundation to the point that it could no longer sustain the…

A: (a) Draw the given diagram of the system.

Q: Consider sampling input cosine functions, with a sample rate of 100Hz. (a) What is Nyquist Frequency…

A: To Find : a) The Nyquist Frequency in Hz. b) The period associated with Nyquist Frequency. c) During…

Q: Part A) A 2D sheet is subjected to the following traction vectors (all vectors have the same…

A: Solution: Given Data: Magnitude of each vector is T. To Find: (a) 2D stress tensor. (b) Principal…

Q: Q.3) A 10 kg bracket ABC is positioned on a table where gravity acts into the drawing (z direction).…

Q: 1-15. Analyze the flow between two plates of Fig. 1-15 by assuming the fluid is a de Wack power-law…

A: (a) Draw the given diagram of the flow.

Q: Determine the specific gravity of a gas mixture of 50% CH4 and 50% C3H8.

A: According to the given data The gas mixture of 50% CH4 and 50% C3H8, we need to calculate specific…

Q: A spark ignition engine has a compression ratio of 8. The condition at the beginning of compression…

A: Given data: Temperature, T1 = 15 C = 288.15 K Pressure, P1 = 95 kPa = 95000 Pa compression ratio, r…

Q: Classify the following processes of a closed system as possible, impossible, or indeterminate.…

A: Given Data: Processes are given of a closed system. So, by using the second law of entropy balance…

Q: Determine the final falling velocity in m/s of particles with a density of 2 g/cm3 that can be…

A: The settling velocity of a particle in a fluid is given by Stokes' Law: v=29×(ρp-ρf)×g×r2μ where v…

Q: Both C's in a parallel-flow heat exchanger are equal to 156 W/K, U 327 W/m²K and A = 2 m². The hot…

A: Given that: Ch = Specific heat of hot fluid = 156 W/K Cc = Specific heat of clod fluid = 156 W/K…

Q: Replace the force system acting on the beam by an equivalent resultant force, and specify its point…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The force A is 35 N. The resultant force is horizontal.

Q: 5. A gas is initially at a gauge pressure of 400 kPa. What is its final gau pressure if its volume…

A: GivenP1=400 kPa (guage)V2=V12Patm=101.3 kPa

Q: Write the constitutive law for a material with linear elastic anisotropic behavior under mechancial…

A: An anisotropic material is one that has different mechanical properties in different directions.…

Q: Consider three forces P1, P2, and P3 where P1 = 28 lb, P2 = 53 lb, and P3 = 54 lb. Determine the x…

Q: ) Determine the stress concentration factor K. 1) For axial load, K=_ 2) For bending load, K=_ 110mm…

Q: 6. In a steam power plant operating on ideal Rankine cycle, steam enters enthalpy of 2789.9 kJ/kg…

Q: Question 2 Determine the velocity and acceleration of cylinder B if cylinder A is pulled down at 3…

A: According to the given data vA=3m/s down aA=2m/s2 We need to find Velocity and acceleration of the…

Q: Q4b. Force vectors F1 and F2 act on body Pwith the resultant force vector R. The resultant force R=…

Q: Calculate the moment capacity (M₁) of a rectangular, singly reinforced beams with the following…

A: Write the given data. fc'=32 MPab=250 mmd=350 mmType of beam: Rectangular singly reinforced beam…

Q: Show that the torque transmitted by a vehicle clutch is given by: 2μΡπ T=5 (R₂³ − R₁³) 3 where: T…

A: Here, constant pressure is given. With the help of constant pressure theory, we have to find torque…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given data:- P = 525 N Detemine:- The angles θx , θy and θz that the force form with the coordinate…

Q: How did you come up with that formula? Explain pls

A: According to the given data in question a=(75-0.025s) We need to prove above given equations

Q: *12-228. At the instant shown, the bicyclist at A is traveling at 7 m/s around the curve on the race…

A: Given: VA= 7m/s (aA)t=0.5 m/s2 VB=8.5 m/s aB= 0.7 m/s2 ρ=50m

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. Hiiii i am having a hard time. It is kinda urgent tysm i appreciate u sm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. hiii pls help urgenttt ty
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a load of 1000 N? Express your answer in N/m2, Mpa, and psi.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a. If the rod passes through a 40-mm-diameter hole,determine the minimum required diameter of the rod and the minimumthickness of the disk needed to support the 20-kN load. The allowablenormal stress for the rod is sallow = 60 MPa, and the allowable shear stressfor the disk is tallow = 35 MPa.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
Kindly give right answer other wise don't attempt Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central hole of 10 mm. It is loaded in an axial tension of 1 kN. Answer-7.813N/MM2