Problem 2Consider sampling input cosine functions, with a sample rate of 100Hz.(a) What is Nyquist Frequency in Hz?(b) What is the period associated with Nyquist Frequency?(c) During one period, how many samples are taken at the Nyquist frequency signal?(d) Give the values at the sample times when you start sampling at time zero.(e) Give the values at the sample times if you are sampling a sine function that is oscillating atNyquist frequency.(f) Give the values at the sample times if you are sampling a cos (wyt - at times t = kTwhere T is the sample time interval for Nyquist frequency (the means that the cosine isshifted 45 degrees back in time compared to the original cosine, i.e. a phase delay from input tooutput).(g) We commented in class that if a cosine is sampled such that there are 4 or more samples ineach period, then the control action based on the sampled values might be able to make someeffective corrective action. If Nyquist frequency is 100Hz, what sample rate is needed for thiscondition.(h) Now consider sampling a cosine whose frequency is 75 Hz. Use the Slide 15 and Slide 21 togive all other frequencies that will have the same values at the sample times.

To Find : a) The Nyquist Frequency in Hz. b) The period associated with Nyquist Frequency. c) During…

Consider sampling input cosine functions, with a sample rate of 100Hz. (a) What is Nyquist Frequency in Hz? (b) What is the period associated with Nyquist Frequency? (c) During one period, how many samples are taken at the Nyquist frequency signal? (d) Give the values at the sample times when you start sampling at time zero. (e) Give the values at the sample times if you are sampling a sine function that is oscillating at Nyquist frequency. 1516 1.T

Consider sampling input cosine functions, with a sample rate of 100Hz. (a) What is Nyquist Frequency in Hz? (b) What is the period associated with Nyquist Frequency? (c) During one period, how many samples are taken at the Nyquist frequency signal? (d) Give the values at the sample times when you start sampling at time zero. (e) Give the values at the sample times if you are sampling a sine function that is oscillating at Nyquist frequency. 1516 1.T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The little brown bat is a common bat species in North America. It emits echolocation pulses at a frequency of 40 kHz, well above the range of human hearing. To allow observers to “hear” these bats, the bat detector as shown combines the bat’s sound wave at frequency f1 with a wave of frequency f2 from a tunable oscillator. The resulting beat frequency is isolated with a filter, then amplified and sent to a loudspeaker. To what frequency should the tunable oscillator be set to produce an audible beat frequency of 3 kHz?
Solve the inverse kinematic problem for the following 6 DOF robot, using the method ofkinematic decouplingif it is known that its Denavit-Hartenberg parameters are as shown in the table inthe table
The acceleration time waveform was obtained from the outboard bearing of a rotor with a looseness problem. The waveform can be described by the equation: A(t) = 0.36sin(1050t +0.07) + 0.21sin(2100t-0.11) + 0.13sin(3150t) – 0.05sin(4200t) g 1. Determine the minimum number of samples for measuring the signal, based on a Nyquist Factor of 2.56. 2. List the frequencies and acceleration amplitudes that appear in the resulting frequency spectrum if an ideal bandpass filter rated at 170 Hz and 600 Hz is applied.
Define Denavit-Hartenberg (DH) kinematic frames and Denavit-Hartenberg (DH) parameters (DH-parameters table) for the manipulator.
15. A manufacturer is scaling up its production of a food product that requires the use of a mixer. If the mixer currently operates at a speed of 500rpm and produces a Reynolds number of 2000 , what would be the required speed of the mixer to maintain dynamic similarity if the product is produced on a larger scale? Given(Re)=(ρuvd)/μ
2.A 31 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 52 revolutions per minute. The lifting drum is situated on the top floor which is 196 m high. How many seconds will it take to lift bricks, three quarters up the height of the building?
Graph/Plot the output step response from t=0 to t=10 with a 0.1-second interval.
I need a Signal-Flow Graph for the element in the image below. Please solve with images and details. Thanks!
The response of a certain dynamic system is given by: x(t)=0.003 cos(30t) +0.004 sin(30r) m (5Mks) Determino: (i) the amplitude of motion. (2Mks) (ii) the period of motion. (in) the linear frequency in Hz. (4) the angular frequency in rad/s. (2Mks) (2Mks) (2Mks) (2Mks) (v) the frequency in cpm. (vi) the phase angle. (2Mks) (vii) the response of the system in the form of x(t) = X sin(t +$) m.
In this Problem, the system of Fig. 5.4.14 (Attached) is taken as a model for an undamped car with the given parameters in fps units. (a) Find the two natural frequencies of oscillation (in hertz). (b) Assume that this car is driven along a sinusoidal washboard surface with a wavelength of 40 ft. Find thetwo critical speeds. m = 100, I =1000, L1 =6, L2 = 4, k1 = k2 = 2000
Help with the MATLAB code to do the following: Given an audio recording of vehicles, compute Power Spectral Density, 1/3 octave band level, octave band level, A-weighted Leq, C-weighted Leq, L10 (unweighted since sample is short), L90 (unweighted since sample is short). If the measurement is made at approximately 50 ft, and that the vehicles are moving at an average of 65 mph, what is the flow rate Q? If instead, the noise is dominated by 1-2 motorcycles, how fast are they going? Given- -The data are in counts -Calibration factor is 133 uPa/count -Sample rate is 44100Hz. -Remember that in air the dB reference is 20 uPa -Pwelch requires that the inputs are doubles
Fourier Methods Question