Determine the principal dimensions of a cone clutch faced with leather to transmit 55 kW at 1100 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume : semi-angle of the cone = 15; μ = 0.2; mean diameter of cone = 6 to 10 d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm2; load factor = 1.75 and mean diameter to face width ratio = 6

Determine the principal dimensions of a cone clutch faced with leather to transmit 55 kW at 1100 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume : semi-angle of the cone = 15; μ = 0.2; mean diameter of cone = 6 to 10 d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm2; load factor = 1.75 and mean diameter to face width ratio = 6

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.
A single disc clutch with both sides effective is required for a vehicle. The power for initial estimation of the clutch is 100 kW at 4000 rpm. Determine the radial dimensions (inner and outer radius) and the actuating force (W). Base the design on the uniform wear assumption. Assume maximum pressure (pmax) as 1.6 MN/m2 and ?2?1= 1√2where ‘r2’ and ‘r1’ represent inner and outer radius of the friction surface. Take µ = 0.35. Find also the minimum pressure (pmin).
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
Q8 A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters ofthe contacting surfaces are 200 and 250 mm respectively. The coeffi cient of friction is 0.1 and themaximum pressure between the contacting surfaces is limited to 0.4 N/mm. Assuming uniform weartheory, calculate the required force to engage the clutch and the power transmitting capacity at 720rpm.
The agricultural machine is powered by an electric motor through a flat beltsystem. The machine requires 6 flat belts and 40 kW power to operate at aspeed of 350 rpm. The pulley diameter of the machine is 650 mm and the pulleyof the electric motor is 330 mm. The centre distance between the pulleys is1100 mm. The belt speed is not to exceed 30 m/s. Calculate the tensions in thebelt.
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock conditions where Ks= 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axesare parallel and in the horizontal plane. The shafts are 8 ft apart. The 6-in driving pulley rotates at1750 rev/min in such a way that the loose side is on top. The driven pulley is 18 in in diameter. Thecoefficient of friction is 0.8. Analyze the centrifugal tension Fc and the torque T.?
A flat belt drive connects two pulleys 5 meters apart. The 2m pulley diameter driver rotates at 350rpm, and the driven pulley has a diameter of 1.5m. The thickness and the mass of the belt drive is 5mm and 0.6kg respectively. The coefficient of friction between the belt and the pulley is 0.25. The belt experience 3% of slip during power transmission with a maximum tension of 1200N.Calculate the speed and torque of the driven shaft.
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
A polyamide F-0 flat belt 80mm wide is used to transmit 5 kW under light shock conditions where Ks = 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axes are parallel and in the horizontal plane. The shafts are 8mm apart. The 50 mm driving pulley rotates at 1750 rev/min in such a way that the loose side is on top. The driven pulley is 50 mm in diameter. The factor of safety is for unquantifiable exigencies. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, Fi and allowable power Ha . (c) Estimate the factor of safety. Is it satisfactory?
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
A leather faced cone clutch transmits power at 500 rpm. The semi-coneangle a is 12.5°. The mean diameter of the clutch is 300 mm, while the facewidth of the contacting surface of the friction lining is 100 mm. The coefficientof friction is 0.2 and the maximum intensity of pressure is limited to 0.07N/mm2. Calculate the force to engage the clutch and the power transmittingcapacity.