Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.

Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.58P: The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of...

See similar textbooks

Similar questions

The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
Torsional coil springs in the clutch disc_____. a. cushion the driven disc engagement rear to front b. are the mechanical force holding the pressure plate against the driven disc and flywheel c. absorb the torque forces d. are located between the friction rings
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A leather faced cone clutch transmits power at 500 rpm. The semi-coneangle a is 12.5°. The mean diameter of the clutch is 300 mm, while the facewidth of the contacting surface of the friction lining is 100 mm. The coefficientof friction is 0.2 and the maximum intensity of pressure is limited to 0.07N/mm2. Calculate the force to engage the clutch and the power transmittingcapacity.
A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure condition can be assumed, what is the required spring force when the plates transmit 20 kW at 1400 rpm?
Refer to Fig 33. The homogenous body A weighs 120 lb. The coefficients of frictions are 0.30 between A and the plane and 2/pi between the rope and the drum. What value of W will cause motion of A to impend? Give solution. (Ans. W= 81.5 lb)
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
Determine the principal dimensions of a cone clutch faced with leather to transmit 55 kW at 1100 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume : semi-angle of the cone = 15; μ = 0.2; mean diameter of cone = 6 to 10 d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm2; load factor = 1.75 and mean diameter to face width ratio = 6.