Determine the reaction forces at the pin support at A and roller support at B of the loaded M kg beam shown in the figure.QSETP(N)Q(kN/m) T(kN/m)M(kg)0,1,275306062.53504 m6 m6 mQuestion 8The horizontal reaction force at the pin iskN.Question 9The vertical reaction force at the pin iskN.Question 10The vertical reaction force at the roller iskN.

Calculate reactions at supports of beam

Determine the reaction forces at the pin support at A and roller support at B of the loaded M kg beam shown in the figure. P Q Q(kN/m) T(kN/m) M(kg) SET P(N) T 0,1,2 75 30 60 62.5 35° 4 m 6 m 6 m Question 8 The horizontal reaction force at the pin is kN. Question 9 The vertical reaction force at the pin is kN. Question 10 The vertical reaction force at the roller is kN.

Determine the reaction forces at the pin support at A and roller support at B of the loaded M kg beam shown in the figure. P Q Q(kN/m) T(kN/m) M(kg) SET P(N) T 0,1,2 75 30 60 62.5 35° 4 m 6 m 6 m Question 8 The horizontal reaction force at the pin is kN. Question 9 The vertical reaction force at the pin is kN. Question 10 The vertical reaction force at the roller is kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the member end moments and reactions for the continuous beam shown in the Figure (a) due to the uniformly distributed load and due to the support settlements of 10 mm at A, 50 mm at B, 20 mm at C, and 40 mm at D. Use the three-moment equation. Ans. MB =115.2 kN.m , MC = 451.2 kN.m, Ay = 138.5 kN, By = 277.9 kN, Cy = 378.7 kN, Dy = 104.9 kN
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m)a) Show the support reactions and load resultant on the rod?b) find the support reactions?c) find the Normal Force, Shear Force and Moment values by cutting from the points you have determined?d) Draw the cross section effect diagrams? Indicate the maximum positive and negative moment values?e) Check the cross-section influence diagrams with a simple method, explain the control steps briefly?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.2 ft, b = 3.3 ft, P = 22 kips, and w = 2.7 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
GIVEN: SUPPORT REACTION AT A = 15KN SUPPORT REACTION AT B = 45KN SUPPORT REACTION AT C = 20KN 1.What is the moment due to the reaction force at point A? 2. A. What is the moment due to the adjusted line load and what is the moment due to line load that cancels out the additional load from the adjusted line load? 3. What is the Area at A1, A2 and A3?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 4.5 ft, P = 21 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
In the figure on the right where there is a single load of 50 N at point B of the given rod system, (between AB: 4m / BC: 1m) a) Calculate the support reactions? b) Immediately after support A, just before point B and immediately after and just before the C-bracket Find the cross section effects by cutting? c) Draw the cross section effect diagrams?
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
In the rigid frame as shown in FIGURE L, if the pulley weighs 2kN, find the following: 1. Reaction at C a. 8 kNb. 11 kNc. 10 kNd. 9 kN34. Reaction at Ba. 28.9 kNb. 27.28 kNc. 26 kNd. 24.7 kN3. Angle that the reaction at B makes with the horizontal. a. 32.71°b. 24.03°c. 31.98°d. 19.11°
reply asap!! An 8-meter long horizontal beam is supported to the left end by a fixed support and supported to the right end by a roller support. A uniformly varying load from O at the left end to 50 kN/m at the right end is applied onto the beam. Assume that the vertical reaction at the roller support is 165% of the vertical reaction at the fixed support. Calculate for the value of the maximum bending moment in the beam (in kN-m). Input to the nearest two decimal places. Add a negative sign before the numerical value of your answer if needed.
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
(i) A tie bar is 2.5 m long, has a circular cross section of 50 mm in diameter and is subjected to a force of 250 kN. Given that Young’s Modulus E = 209 kN/mm2 and Poisson’s Ratio ν = 0.3 calculate the change in volume of the bar when loaded. (ii) Draw the shear force and bending moment diagrams for the cantilever beam shown in the image attahced clearly indicating all significant points.