Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y= 14 kN/m L= 3 m What is the reaction (kN) at the hinge support? Type answer in two (2) decimal places only without the unit. Y (kN/m) X (kN/m) Y-5 (kN/m) 5 kN/m 5 kN/m A В C L (m) 10 m

Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y= 14 kN/m L= 3 m What is the reaction (kN) at the hinge support? Type answer in two (2) decimal places only without the unit. Y (kN/m) X (kN/m) Y-5 (kN/m) 5 kN/m 5 kN/m A В C L (m) 10 m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.9P

See similar textbooks

Related questions

Q: Sandy is a squirrel who lives in a hemisphere under the sea (SG = 1.02). The hemisphere has a radius…

Q: A cantilever beam, 70 mm wide by 260 mm high and 8 m long, carries a load that varies uniformly from…

Q: ) Explain the difference between wetting fluid and non-wetting fluid (b) The 60m X 60m rectangular…

A: Wetting fluid - fluids in which adhesive forces ( between different kind of molecule) are stronger…

Q: 3. A simply supported beam AB of span 6 m is loaded as shown in Fig. 12.14. 2 kN 5 kN 2 kN/m 2 kN/m…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: For the following beam: 4 N/m 60 kN 3 kN/m 10m 30m 10 m Determine the maximum flexural bending…

Q: PSCS SHS 2122: Lo. Determine the axial force (kN) in each member of the assembly shown below, Member…

Q: As the consultant for designing STP, you proposed to use a completely-mix activated sludge system…

A: Answer We are given Population = 45000 PE Influent BOD in primary clarifier = 300 mg/l Influent SS…

Q: Given the depth of grit chamber is 1 m, while settling velocity, vs, density, s and dynamic…

Q: Statically indeterminate 2-span beam (as labeled Element 1 and 2) is shown below. Assume EI is -…

Q: A cantilever beam, 80 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from…

Q: In a certain road construction undertaken by the DPWH, it was decided to connect a forward tangent…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: First Calculate strain at given Fiber Ab and Cd which is already calculate using change in length /…

Q: sil Find the moment of inertia (Ix, mm“) of the composite shape from the bottom base. Type answer in…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: A timber beam 92 mm wide by 160 mm high is subjected to a vertical shear V = 27 kN. Determine the…

A: Given data in question Width Height Shear force Height of layers To find out Shearing stress at…

Q: 3. A simply supported beam AB of span 6 m is loaded as shown in Fig. 12.14. 2 kN 5 kN 2 kN/m 2 kN/m…

Q: Solve for the total hydrostatic force and its location with repect to oil surface S : 08 am 8m

Q: The members of the truss shown below have a cross- sectional area of 10,000 mm2. Determine the…

Q: The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the…

A: Given data in question Cross section Diameter of bar Number of bars Stress Elasticity modulus To…

Q: A reverse curve with diverging tangent is to be designed for a proposed highway as illustrated…

Q: How many compatibility equations are needed to be added to the equilibrium equations to solve for…

Q: A square footing has a dimension of 1.78 m x 1.78 m and has its bottom 1.54 m below the ground…

Q: 14 kN/m B A 5 m 3 m- Fig. P9.53

Q: 1. A welded connection is in equilibrium under the action of the four forces shown. Knowing that FA…

Q: What is the shearing stress developed at the neutral exis of the beam with a circular cross section…

Q: The company that you are working for is currently in the planning stage of road construction in an…

Q: The standard length of a tape is 100m having a weight of 2kg with the standard temperature of 20°C…

Q: Calculate the total volume (m3) from Station A to B if the following cross sections were provided:…

Q: Which among the following is the expression for the moment function of the beam shown with respect…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: 11. PRACTICE PROBLEMS ri- are of 1. The interior angles shown were measured for a five- sided closed…

Q: ent diag

Q: A cantilever beam, 80 mm wide by 220O mm high and 9 m long, carries a load that varies uniformly…

Q: QUESTION The figure shows an idealized two-cell symmetric wing box structure. Dimensions of the box…

A: An idealised two-cell symmetric wing box construction is shown in the diagram. The wing box's…

Q: A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The…

Q: If the Sun suddenly turned off, we would not know it until its light stopped coming. How long would…

A: Distance from sun (d) = 1.5 x 1011 m Velocity of light in vacuum (v) = 3x108 m/s

Q: 1. Replace the force system by a resultant force and couple moment at point O. 500 N 750 N 200 N 1 m…

A: A loaded cantilever beam is given and it has been asked to determine moment at o. Please refer step…

Q: etermine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: show

A: angle = 188°59'30''

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: Which among the following is the equation of the elastic curve for a cantilever beam of length L,…

A: Given data in question Cantilever beam Span member length Point load at free end To find out…

Q: A 24-mm-diameter solid shaft is subjected to an axial force of P = 4700 N, a horizontal shear force…

Q: A 3 m x 3 m square precast reinforced concrete segments to be installed by pushing them through an…

Q: A timber beam 91 mm wide by 160 mm high is subjected to a vertical shear V = 27 kN. Determine the…

A: Given data, V = 27 kN Width of beam = 91 mm Height of beam = 160 mm Each layer 20 mm apart To…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: A horizontal beam AD is supported by an inclined strut BC carries a load W = 2.4KN at the position…

Question

Show your detailed solution and write eligibly

Determine the reaction/s at each support, given the data and figure below.
X= 3 kN/m
Y= 14 kN/m
L= 3 m
What is the reaction (kN) at the hinge support? Type answer in two (2) decimal places only without the unit.
Y (kN/m)
X (kN/m)
Y- 5
(kN/m)
5 kN/m
5 kN/m
C
L (m)
10m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 4.7 m, b = 18 kN/m, c = 15 kN.
For the beam loaded as shown in the figure 2, determine the reaction at D in kN using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
Using Three-Moment Equation, determine the reactions at the support of each beams shown below. PLEASE TRY TO ANSWER IN 30MINS....
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the vertical reaction at point C, if the log is 12 ft long.
For the beam loaded as shown in the figure 1, determine the reaction at A in kN using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. a = 3.9 m, b = 9 kN/m, c = 15 kN.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the horizontal reaction at point C.
For the system shown, the masses of A and B are 55 kg and 135 kg, respectively. The cocfficient of static friction between block B and the surface C is 0.12 and the coefficient of static friction between blocks A and B is 0.10. The coefficient of friction between the rope and the pulley is 0.10. What is the maximum mass M that can be suspended as shown and still maintain equilibrium?
A 4-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the vertical reaction at point C, if the log is 12 ft long. CHOICES A.) 658.68 B.) 568.88 C.) 856.86 D.) 865.65
Gate AB in the figure is 16 ft long and 8 ft wide. Neglecting the weight of the gate, Find the Force acting on the gate shown, if P is –15 kPa (suction), and its location from the hinge, the tank is 3 meters wide.a. P=304.74 kN, 3.30 m c. P=979.74 kN, 2.75 mb. P=529.74 kN, 2.96 m d. P=678.95 kN, 2.87 m
For the beam loaded as shown in the figure 2, determine the moment reaction at A in kN-m using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 2.9 m, b = 32.9 kN/m, c = 20 kN.
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.