Answered: Determine the reactions for the…

Determine the reactions for the continuous beam shown by the three-moment equation. Draw the shear and moment diagram. 38 kN/m 4.2 m 41 kN/m B 21 3.8 m 86 KN 91 KN 1m Im 1 m 2.5 m 32 kN/m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: aqil t A E 10' 12,000 lbs B 20' 4000 lbs (alg 21) Siog 16 insmom erit animated BS 1996091616092 no…

Q: Could you explain in more detail on how to plot the graph on excel for me to follow come up with the…

A: Given: Plotted Gradation curve:

Q: Two homogeneous pumps runs at a same speed of 500 rpm. Pump A has diameter 50 cm and discharges 0.6…

A: Given- Same speed=500 rpm Diameter=50 cm discharge=0.6 m3/s, Net head=50 m, Pump B discharge=0.3…

Q: Calculate for the axial force in kN at member CB of the frame shown in figure 2 using Cantilever…

A: Answer We have two assumptions of cantilever method to find axial force in member CB. 1) Point of…

Q: The beam is supported by a pin at B and a roller at D. The applied loads shown in the figure have…

Q: The volume of the earthwork in embankment of length 14 m, Top width 7 m and depth of 3 m is: Assume…

Q: The bar below is subjected to uniaxial tension. Assuming that the bar material behaves elastically,…

Q: Find the quantities of cement, sand and coarse aggregates in 1 m³ of concrete for a mix 3 proportion…

Q: Given (Refer to the pictures): Shear and moment diagram of B2 Requirement: What is the…

Q: A four-meter intermediate floor beam is made of ASTM A992 steel (Fy = 350 MPa; F = 450 MPa) rolled…

A: Answer (a) Local stability of beam Flexure sections are classified as compact when limiting width…

Q: Show solution and diagrams.

A: Given: Span; L = 5 m a = 2 m UDL, Wu = 80 kN/m fc = 25 MPa fy = 415 MPa b = 310 mm h = 525 mm rebar…

Q: 7- Describe the flowchart of the experimental mechanistic design along with the relevant steps.

A: A flow chart is a logical arrangement of shapes, lines, and text that visually depicts a procedure…

Q: Water flows in a triangular channel of side slope 1 horizontal: 1 vertical and longitudinal slope of…

Q: Find the quantities of cement, sand and coarse 3 aggregates in 1 m³ of concrete for a mix proportion…

Q: A rectangular footing is constructed on saturated sand. This footing is placed under 1000 KN column…

A: given data- Total load acting on the footing = 1000 KN Moment acting on the footing= 500 KNm size of…

Q: At a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is…

Q: A loose, uncompacted sand fill 6-ft in depth has a relative density of 40%. Laboratory tests…

A: Given, Ho = 6 ft Dr = 40% or 0.40 emax = 0.90 emin = 0.46

Q: 4. Find the tension in the cable AB A vinove 916 2901t own ort bgnol 1991 81 al meed sriT 8 19llo1…

Q: 1.) Use the Triangle Rule and the Law of Cosines to find the magnitude of the resultant force FR =…

Q: Calculate the approximate specific energy of a trapezoidal channel having a bottom width of 5m,…

A: Given data- A trapezoidal channel- Bottom width b=5 m, Side slope 1:1, Depth y=2 m, Discharge Q=15…

Q: When discussing most efficient section in open channels, what is the perimeter, P as a proportion P…

A: Given data- Most efficient trapezoidal channel- Width=B, Height=h, Side slope= 1 V : m H, To Find-…

Q: One cumec of water is pumped into a farm distribution system. 0.8 cumec is delivered to a turn-out,…

A: Given that :- Water delivered to the field = Wf=0.8 cumec Water delivered from the reservoir = Wr=1…

Q: "Repository, modelling tool, documentation instrument, engineering instrument, and construction…

A: 1. Repository A repository is a central location where data, information, or software code can be…

Q: The in-situ void ratio of a granular soil deposit is 0.59. The void ratios in loosest and densest…

Q: During a compaction test, a soil attains the maximum dry unit weight of 18.6 kN/ m³ at a water…

Q: The in-situ void ratio of a granular soil deposit is 0.59. The void ratios in loosest and densest…

Q: A canal irrigates a portion of a culturable command area to grow sugarcane and wheat. The average…

Q: (ii) The readings given below were made with a tacheometer theodolite having a multiplying constant…

A: Answer Given data The elevation of station A = 100.00 m The height of instrument (HI) = 1.35 m…

Q: Figure 4 in. X 3 in. a < 1 of 1 Part A Locate the centroid of the cross-sectional area. Take a = 0.7…

Q: Imagine the eccentricity is more than the allowable eccentricity (e₁>) in a rectangular footing with…

A: Given: Vertical load on the footing = P The eccentricity of the load = eL The shape of the footing:…

Q: Problem 6 Identify the zero-force members in the following trusses, by observation only. Identify…

A: Given data in question Structures Loads To find out Zero force members

Q: The surface of a saturated clay deposit is located permanently below the groundwater table. The clay…

A: Given: The clay has natural water content = 43 % Specific gravity = 2.70 The vertical intergranular…

Q: 4. A reservoir discharges into a 60-inch concrete pipe (rough surface) that dis-charges freely, as…

A: Given, D = 60 in or 5 ft Pipe material is Concrete

Q: A steel penstock 60 cm in diameter has a shell thickness of 1.2 cm. The modulus of elasticity of the…

Q: Determine the radius of a taxiway for a supersonic aircraft to negotiate the curve at a turning…

Q: For a typical catchment, the following precipitation and corresponding runoff data were observed;…

A: Given: Year Mean annual rainfall Mean annual runoff 1990 1188 374 1991 1213 420 1992 1612…

Q: The volume of the earthwork in embankment of length 14 m, Top width 7 m and depth of 3 m is: Assume…

A: Volume of Earthwork

Q: The top width and the bottom width at river thalweg level of a concrete gravity dam are 6 m and 24 m…

A: Given data- Top width h=6 m, Bottom width H=24 m, Vertical section is 38 m above the thalweg, Depth…

Q: Design slow sand filter beds for a population of 60,000 persons with per capita demand of 135…

Q: Assuming Fe410 steel, classify the following sections: (a) ISLB 350 @ 472 N/m (b) ISHB 400 @ 806 N/m…

Q: LO2 Explore alternative construction methods which are fit for purpose in a given context. P3-…

A: LO2. Alternative construction methods are becoming increasingly popular as they offer a range of…

Q: Given the following data for two of the Great Lakes Volume (km3) Q (m3/sec) Lake Superior…

A: Given data for two of the Great Lakes is: Lake Volume (km3) Discharge, Q (m3/sec ) Lake…

Q: CIVIL ENGINEERING (Drainage): Calculate the average exceedance probability for the 51-year/7-hour…

Q: A simple roof truss has a tie beam of 13 m and rafters 6 m and 10 m. Taking the points as hinged,…

Q: technique or method used to select the rebuild elliott bay seawall project

Q: Problem 5: Method of Sections Inputs: ● ● ● B H I a d = 4 m a = 3 m (all horizontal members are this…

A: Given data in question Load 45 kN Span 3 m each and 4m To find out Force in member CJ

Q: A cantilever beam is having Young's modulus E = 2 x 105 N/mm², Moment = of Inertia I 8 x 107 mm 4…

Q: Calculate the approximate specific energy of a trapezoidal channel having a bottom width of 5m,…

A: Given Data Bottom width (B) = 5m Side slope (1:m) = 1:1 Discharge (Q) = 15 m3/s Depth of flow (y)…

Q: Cylinder 1.2 m in diameter and 9 m long rotates at 210 rpm with its axis normal to an air stream of…

Q: Question 3: The parameters of a soil are λ = 0.26, x = 0.06, cs=24°, v' = 0.3, € = 1.08, p = 280 kPa…

A: Given data- Soil parameters given- λ=0.26,k=0.06,ϕ'cs=24o,v'=0.3,eo=1.08,p'c=280 kPa,Ro=7 Soil is…

Concept explainers

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.

Question

STRUCTURAL THEORY | USE THREE MOMENT EQUATION and PUT THE WHOLE SOLUTION.

Determine the reactions for the continuous beam shown by the three-moment
equation. Draw the shear and moment diagram.
41 kN/m
32 kN/m
86 kN
91 kN
38 kN/m
B
D
1
4.2 m
3.8 m
1 m
1m
2.5 m
21

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve for the reactions and draw the shear and moment diagrams of the following beams using both Three-Moment Equation (3ME) and Slope Deflection Method (SDM) for this beam. W = 12 , P = 57 , EI = constant
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
Determine the member end moments and reactions for the continuous beam shown in the Figure (a) due to the uniformly distributed load and due to the support settlements of 10 mm at A, 50 mm at B, 20 mm at C, and 40 mm at D. Use the three-moment equation. Ans. MB =115.2 kN.m , MC = 451.2 kN.m, Ay = 138.5 kN, By = 277.9 kN, Cy = 378.7 kN, Dy = 104.9 kN
Analyze the beam: Plot the shear diagram, moment diagram, elastic curve and axial diagram of the following, where P=55
look for: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
Compute the reactions and draw the shear andmoment curves for the beam in Figure P9.20. Given: EI isconstant for the beam. E = 200 GPa, I = 40 × 106 mm4
Determine (a) the absolute maximum values of shear and moment in the beam produced by the wheel loads and (b) the maximum value of moment when the middle wheel is positioned at the center of the beam in Figure P12.43.
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 507 N , Q = 382 N, and T = 451 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 12 kN-m Ay = 3.37 kN Dy = 32.63 kN
Determine the reactions on the beam given the loadings below using VIRTUAL WORK METHOD. Use the reaction at C as redundant. x1= 3.5 m x2= 1.5 m w1= 30 kN/m w2= 20 kN/m M= 9 kN/m (EI)AB = 1.5EI E= 40x10^6 mm^4 I= 200000 MPa
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
ANSWER CORRECTLY: Using the portal method, calculate for the magnitude of the moment reaction at support C. Express your answer to the nearest whole number, in kN-m.