Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially stressed and take the safe tensile stręss as 2000 kg/cm" . 2- An eye bolt carries a tensile load of 2000 kg. Find the size of the bolt, if the tensile stress is not to exceed 1000 kg/cm. Also draw a neat proportioned figure for the bolt or

Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially stressed and take the safe tensile stręss as 2000 kg/cm" . 2- An eye bolt carries a tensile load of 2000 kg. Find the size of the bolt, if the tensile stress is not to exceed 1000 kg/cm. Also draw a neat proportioned figure for the bolt or

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
An eye bolt carries a tensile load of 20 kN. Find the size of the bolt (in mm), if the tensile stress is not to exceed 100 MPa. Draw a neat proportioned figure for the bolt. (
An eye bolt carries a tensile load of 20 kN. Find the size of the bolt , if the tensile stress is not to exceed 100 MPa.
An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress is not to exceed100MPa. Draw a neat proportioned figure for the bolt.
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
(1) Find the factor of safety allowed in a piston rod 200 mm diameter if the maximum tensile pull in the rod under working conditions is one MN and the tensile strength of the piston rod material is 600 MN/m2.
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
A mild steel rod having a stress of 50 Mpa and having a diameter of 20 mm What is the force applied on it.
An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder head is held by 12 studs, find the size. Assume safe tensile stress as 28 MPa.