Determine the slope and deflection at C by the conjugate beam method. E = 200GPa and I = 500x106mm4. IABC = 21 while ICDE = I 40kN 20kN 15kN C A 2m 4m 13m 6m D SW 1m

Q: Consider a wood beam (see figure) carrying a uniform load of 31.5 kN/m (which includes the weight of…

A:

Q: al-sized pieces and arranged as si ermine the ratio of the drag on the o

A: Drag force is given…

Q: If the free end of a cantilever of span / and flexure rigidity El undergoes a unit displacement…

A:

Q: Determine the shear and moment as functions of x and draw the shear and moment diagrams for the beam…

A: ASKED: To determine the shear and moment functions and draw their corresponding diagrams.

Q: Determine the forces in the members identified by ‘‘x’’ of the truss shown by the method  of…

A: To Determine the forces in the members identified by ‘‘x’’ of the truss shown by the method of…

Q: A 30 cm diameter cast iron pipe conveys water at 20°C at the rate of 0.2m³/sec. What is the head…

A: Given data:- Diameter of pipe, d=30 cm=0.3 m Area, A= 3.14/4 ×0.32=0.07 m2 Discharge, Q=0.2 m3/s…

Q: Answers: 0x = Txy Op2 = i i i MPa MPa MPa

A:

Q: 9.22 An atmospheric boundary layer is formed when the w blows over the earth's surface. Typically,…

A:

Q: d. A steel rod with a diameter of 30 mm and 800 mm long has an allowance elongation not to exceed…

A:

Q: 4. A trapezoidal masonry retaining wall 1 m wide at top and 3 m wide at its bottom is 4 m high. The…

A: Given: A trapezoidal masonry retaining wall 1 m wide at top and 3 m wide at bottom and 4 m height…

Q: Can anyone explain this formula why it has an Ao or Area of orifice when its a weir problem. Where…

A: Given data,

Q: b) A rectangular block of 1200 mm² cross-sectional area is subjected to a longitudinal compressive…

A: The angle given is 40 degrees

Q: Find the value of final velocity of car U=2.5 m/s a=1 m/s2 t=3.5 s

A:

Q: g at 4 m/s through water. Estimate the por of the log is parallel to the tow direction

A: νw=1.12×10-6m2sρw=998.8kgm3Re=vDν=4×21.12×10-6=7.14×106so,Aspect ratio =LD=82=4For circular ract…

Q: an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used sure of 2.2 MPa. rmine…

A:

Q: A 12-meter-long beam is simply supported at the right end and at 2 meters from the left end. It is…

A:

Q: Floor plan of a building: Fire Barrier Wall Firewall As regulated by the building code, how many…

A:

Q: Problem 8 A 30 cm diameter cast iron pipe conveys water at 20°C at the rate of 0.2m³/sec. What is…

A:

Q: The saturated unit weight of a soil is 19.8 kN/m³. The moisture content of the soil is 17.1%.…

A: Given data : The value of saturated unit weight γSat=19.8 KN/m3 The value of moisture content…

Q: SITUATION. The figure shows a highway bridge truss. S F G H A B C FE FE 市 Given: S=4m H = 5m Due to…

A: (D) 16m is the correct answer.  The question is based on the influence line diagrams. Draw the…

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

A: Given data :-  Type of channel :- Rectangular channel  Wetted area (A) = 16 m2  Wetted perimeter (P)…

Q: 12. For the Dam shown in the figure a) Draw the flow net in the soil under the dam b) Calculate q…

A: Note :- nothing said about how many flow lines and equipotential lines to be drawn so taking it as…

Q: A cantilever beam 4 m long deflects by 16 mm at its free end due to a uniformly distributed load of…

A:

Q: 20. A trapezoidal canal, 6m at the bottom and having side slopes 2:1 carries water to a depth of…

A:

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No.…

A: ASKED: To determine the coefficient of uniformity for the given soil.   Given, Sieve No. Opening…

Q: 7000

A:

Q: A body floats half and submerged in a certain liquid (s.g. = 1.25) and has a weight of 500 kN.…

A:

Q: SITUATION. A truss is loaded and supported as shown below. It is carrying a vertical point load at…

A: Cut the section XX such that AB, CD and EF is intersected. Then calculate the moment about the point…

Q: A rectangular beam with a width of 360 mm and total depth of 540 mm and reinforced with 4- 22 mm…

A: Answer We are given Width b = 360 mm Total depth h = 540 mm Tension steel area As = 4-22 mm dia…

Q: Problem 8 A 30 cm diameter cast iron pipe conveys water at 20°C at the rate of 0.2m³/sec. What is…

A: Given -

Q: Pitot Pipe By connecting a mercury pressure gauge to a vertical pipeline through which water is…

A: step 1-

Q: Calculate allowable bearing capacity of the following foundation Ground Surface 4 ft x4ft 17 = 110…

A: Given -

Q: A solid brass [E = 98 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each…

A: Figure is as shown

Q: SITUATION 2 Using the Portal Frame Method: 36 kN .B 10m 8m A 21-25) Determine the Shear force on…

A:

Q: A pad footing of dimensions 1.2 m by 2.5 m applies a surface pressure of 425 kPa. The pad footing is…

A: Given: The dimension of the footing is 1.2 m x 2.5 m. The surface pressure is 425 kPa. The thickness…

Q: Given data: Stress=20 N/mm2 Area=5 mm2 Find the force applied on cross sectional area

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: > Commercial trucks begin to arrive at a seaport entry plaza at 7:50 a.m., at the rate of λ(t) = 6.3…

A:

Q: shown, calculate the initial tension induced in each cable immediately after release ngular…

A: Given Data -

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

A:

Q: A vehicle is moving along a straight line having an initial speed of 10 m/s. It is experiencing a…

A: To find the distance travelled after three seconds

Q: Calculate the amount of steel required in a T-beam to develop a moment of resistance of 300 kNm at…

A:

Q: The bolt shown in figure is subjected to a total tensile force of 90 kN. Determine the tensile…

A: Force will be same in each case.

Q: The beam-column shown below is pinned at both ends and is subjected to the loads shown. Bending is…

A: Given, PD=534 kNPL=569 kNMDTop=243 kN-mMLTop=206 kN-m  MDBot=125 kN-m  MLBot=64 kN-m  L=4.57 m…

Q: What is the maximum allowable building area (square feet) based on the diagram below and the given…

A: Given data, Office building - Single story VB construction No sprinkler system

Q: ne axial load, shear and bending me O kN/m B

A:

Q: Determine the value final velocity U=2.5 m/s a=3 m/s2 t-4.5 s

A: Intial velocity U = 2.5 m/s acceleration a = 3 m/S2 time t = 4.5 s Final velocity v = ?

Q: Calculate static indeterminacy of truss

A:

Q: part (b). |--213-1² 12 in. 2 in. 2 in. 2 in. 3 in. 2 in. 3 in. 4 in. 4 in. (a) (c) (b) The allowable…

A:

Q: An airflow at 25-degrees C and 50 kPa with a velocity of 900 m/s is turned by an abrupt 25-degree…

A: Normal shock tables: In aerodynamics, a series of various tabulated data regarding the different…

Q: Need asap. Please input the right formulation and solution. Provide explanation thank you. Answer on…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.