Determine the terminal velocity of a 100 mm diameter cylinder, having a length of 360 mm and weighing 20 N, falling inside a vertical 100.2 mm ID pipe if the gap between cylinder and pipe wall is filled with SAE 30W oil at a temperature of 60°C. Ucyl = 1.438 m/s

Determine the terminal velocity of a 100 mm diameter cylinder, having a length of 360 mm and weighing 20 N, falling inside a vertical 100.2 mm ID pipe if the gap between cylinder and pipe wall is filled with SAE 30W oil at a temperature of 60°C. Ucyl = 1.438 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 10-kg block slides down a smooth inclined surface as shown in below figure . Determine the…

Q: A liquid is being pumped through a pipe whose diameter is 15mm. At the operating temperature and…

Q: The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with…

A: Given: toil=2 mmμ=0.38 Ns/m2d=30 cmN1=1200 rpmN2=1125 rpm

Q: A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface…

Q: A liquid of viscosity of 0.03 N s m 2 is flowing under laminar conditions through a convergent,…

A: To find : determine the pressure drop which is required to maintain the flow rate Given, viscosity…

Q: The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? =…

A: Given data: Speed of driving shaft, N1 = 1200 rpm Speed of driven shaft, N2 = 1125 rpm Thickness of…

Q: Q1: Air at 300 K and 50 kPa flows over a 2-m-square plate at a velocity of 70 m/s. The plate is…

Q: The maximum velocity with which a fluid 3. having density of 90kg/m and viscosity 0.1 Ns/m2 can flow…

Q: Heated air at 1 atm and 35 °C is to be transported in a 150 m long circular plastic duct at a rate…

Q: fan is used to force air having a temperature of 20°C through the 200-mm diameter galvanized sheet…

Q: A 1.2-in-outer-diameter pipe is to span across a river at a 115-ft-wide section while being…

A: Given: The outer diameter of the pipe is D=1.2 in. The width of the river is W=115 ft. The average…

Q: Hydrogen (viscosity = 0.009 centipoise) is pump from a reservoir at 2x10³ kPa pressure through a…

A: Given DataP1=2.6×103kPaP2=2×103kPad=50mmL=500m **In Question there is no demand of any terms for…

Q: Air at 30 °C and 1 atm is flowing over a long flat plate with a velocity of 10 m s. Its…

Q: The relation of flow between parallel flat plates is

Q: What is the difference in force needed to stabilize a flat plate being sprayed with a jet of water…

A: The force exerted by jet depends on the area of jet or nozzle, velocity of jet coming out through…

Q: A liquid is being pumped through a pipe whose diameter is 15mm. At the operating temperature and…

Q: Hydrodynamic journal bearings have been widely used to support high speed rotating machinery such as…

Q: What is the Reynolds number and flow regime at the beginning and at the end of the pipe? If the…

A: It is given that Diameter of pipe (d)= 50 cm = 0.50 m length of pipe (L)= 10 m mass flow rate m.=…

Q: : A piece of pipe 30 cm long weighting 1.5 kg and having internal diameter of 5.125 cm is slipped…

Q: In the design of small-scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100…

A: As per the question mentioned, it is a shear sensitive Newtonian liquid , it mean it is case of…

Q: what is the Definition Reynolds number for internal pipe flows, give information for all terms, what…

A: Reynolds number is a dimensionless number used to predict the type flow. Laminar flow, transition…

Q: Calculating the Reynolds numbers at the end of the plate for the following fluid flowing over a 15cm…

Q: Determine the inside diameter of a tube that could be used in a high temperature, short time…

Q: What is the physical significance of the Reynolds number? How is it defined for external flow over a…

A: Given: Plate with length L To find; Significance of Reynolds number Reynolds number for external…

Q: Air ( density :1,2 kg /m3 viscosity : 1.5x10-5 m2 /s ) flows over a flat plate of length 2,5 m and…

A: Given, ρ = 1.5 kg/m3v = 1.5 × 10-5 m2/sL = 2.5 mW = 1 mV = 1.5 m/s Total area exposed for drag (A)…

Q: What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The…

Q: Define Reynolds number for internal pipe flows, give information for all terms, what is the critical…

A: Reynolds Number (Re): It is a dimensionless number. It is defined as the ratio of inertia force to…

Q: Air is flowing at a speed of 5 m/sec between two parallel flat plates. The air temperature is 20o C…

A: Write the given data with suitable variables. v=5 m/sT∞=20 °CP=1 atmT=90 °Cd=60 cm=0.6 m100 cm1 mb=1…

Q: Air with a pressure of 1 atm and a temperature of 285 K flows in a duct rectangular shape with a…

A: Given, Pressure, P=1atmTemperature, T=285KMass flow rate, m=0.1kg/sDuct size=75mm×150mmLength of…

Q: A square metal plate 1.5 m side and 1.5 mm thick weighing 50 N is to be lifted through a vertical…

Q: A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface…

Q: Air at 15 m/s is cooled from 80 C to 60 C in 2.5cm diameter tube. The tube wall is maintained at a…

Q: - Air x10° m/s) flows along a flat plate with a velocity of 150 km/hr. How long loes the plate have…

Q: The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with…

A: Given DataN1=1200rpmN2=1125rpmD=0.3mμ=0.38N-s/m2

Q: JAn electronic device is cooled by water flowing through capillary holes drilled in the casing. The…

Q: Consider laminar flow of a fluid over a flat plate. Now the free-stream velocity of the fluid is…

A: Drag force is given as –

Q: How does the viscosity affect the drag force?

A: Explaining the effect of viscosity on drag force

Q: Write your answer in 4 decimal places. DO NOT round off intermediate values. Water at a mean…

A: Given:T=25°Ca=1 cm =0.01 mRe=10,000

Q: In an Osborne Reynolds Demonstration experiment, why is it the in laminar flow, the color collected…

A: Osborne Reynolds Demonstration is an experiment conducted to demonstrate the various flow patterns…

Q: 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If the…

A: Dear student, According to the expert guidelines I am allowed to answer only…

Q: Explain why the friction factor is independent of the Reynolds number at very large Reynolds…

A: As we know reynolds number Re=ρνDμwhereρ=density of fluid V= velocity of fluid μ=viscosity of fluid…

Q: Consider a person walking first in the air and then in the water at the same speed. Which motion…

Q: Q1) A shaft of diameter (d 41-mm) is to be pulled through a (44.1)-cm-diameter glycerin-filled…

Q: A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is…

A: we are supposed to answer only 3 sub parts..please post other parts as the other question.

Question

100%

Current Attempt in Progress
X Your answer is incorrect.
Determine the terminal velocity of a 100 mm diameter cylinder, having a length of 360 mm and weighing 20 N, falling inside a vertical
100.2 mm ID pipe if the gap between cylinder and pipe wall is filled with SAE 30W oil at a temperature of 60°C.
Ucyl =
i
1.438
m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the Height of a chimney with a static draft of 12 mm if the losses total draft is 4 mm, the ambient air temperature is 35 ° C and theexhaust gas temperature is 450 ° C. The fuel consumption of the boiler is 600 kg / h, the mass of the exhaust gas is 16 kg, also determine the air mass ma, the diameter of the chimney and the velocity of the exhaust gases.
A fan is used to force air having a temperature of 20°C through the 200-mm diameter galvanized sheet metal duct. Determine the required power output of the fan if the length of the duct is 150 m and the flow is to be 0.15 m3/s. Take f=0.023, density of air = 1.202 kg/m3, and kinematic viscosity of air = 15.1×10-6 m2/s.
Glycerin, with a density of 1260 kg/m3 and an absolute viscosity of 1.5 kg/m.s, flows in a tube with an internal diameter of 5,0 cm, but it is not known whether the regime is laminar or turbulent. Knowing that the length of the hydrodynamic inlet of this flow is 0.2 m, determine the velocity of the oil and the flow regime. (the form is in the side picture)
Two parallel plates kept 0.01 m apart have a laminar flow of oil between them, Taking dynamic vinconity of oil to be 0.8 poise, determine the velocity distribution, discharge and shear stress on the upper plate that moves horizontally at relative velocity Im/sec with respect to the lower plate which is stationary. Further the pressure drops in the flow direction from 180 kPa to 100 kPa over a distance of 80 m.
The duct has a cross section 15 cm x 20 cm made of commercial steel, has air flowing steadily at 1 atm and 35C and at an average velocity of 7m/s. Solve for the fan power requirement in W disregarding the entrance effects. The length of the duct is 10 m long. Round your answer to 4 decimal places.
Oil with a viscosity of 30 cp and density of 600 lb/ft³ flows through a ½ in ID tube. Determine the velocity in ft/s in which the flow is laminar.A. 13.1B. 169C. 87.2D. 0.63
The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
Determine the terminal velocity of a raindrop having a diameter of 30 x 10-5 if the density of air is 1.2 kg/m3 and having a dynamic viscosity of 18 x 10-6 N.s/m2.
Crude Oil is flowing through a circular pipe with a centerline velocity of 0.5m/s at a temperature of 60 degrees Celcius and viscosity of 5.5 mPa s. Determine the shear stress at the pipe surface if a parabolic velocity distribution is assumed. Also, indicate the kinematic viscosity of the crude oil at the given temperature. The density of the crude oil is 855 km/m^3 and the pipe diameter is 20 mm.
An 18-kg slab slides down a 15° inclined plane on a 3-mm-thick film of oil with viscosity of 0.0814Pa-sec. If the contact area is 0.3m^3, find the terminal velocity of the slab. Neglect air resistance. ans. 5.614 m/s
What is turbulent viscosity? What causes it?
When the free-flow velocity on the plate is 10 m/s, (a) when water with a kinematic coefficient of 1.14×10‾ⁿ (n=6) m²/s flows and (b) when air with a kinematic coefficient of 1.51×10‾ⁿ (n=5) m²/s flows, the flat plate How long can we assume that laminar flow is maintained from the front end of Critical reynolds number Re=50×10⁴