Determine the value of Zpase for the circuits. +10 V ERc -4 kN 10 kN HE R 11 k2 hie = 200 R2 2.2 kN 200 N RE 910 N Assuming the components are changed to the following values: Vcc = 11 Volts R1 = 10,088 ohms R2 = 2,294 ohms Rc = 4,095 ohms %3D rE = 247 ohms %3D RE = 967 ohms %3D RL = 11,073 ohms %D hfe = 265 %3D

Determine the value of Zpase for the circuits. +10 V ERc -4 kN 10 kN HE R 11 k2 hie = 200 R2 2.2 kN 200 N RE 910 N Assuming the components are changed to the following values: Vcc = 11 Volts R1 = 10,088 ohms R2 = 2,294 ohms Rc = 4,095 ohms %3D rE = 247 ohms %3D RE = 967 ohms %3D RL = 11,073 ohms %D hfe = 265 %3D

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

D-MOSFET: lVtl= 2 V, Idss =10 mA, Is=1.6 mA, rd=14 K, RL=2 K. Calculate the dc drain-to-source voltage. Please write your answer as a V and don’t use units in the answer. Please use one digit after the dot.
Six 100Wp crystalline PV modules, each with an open circuit voltage (Voc) of 30V, are connected in series in a string. What would be the total open circuit voltage (Voc) of the string of modules? And what would be the total Wp of the string? 180V, 600Wp 180V, 100Wp 30V, 600Wp 30V, 100Wp The distance from a combiner box to a PV array junction box is 4 m. The voltage drop of the used cable on this distance is 0.5 V. The current is 8.0 A. What is the power loss on this distance? 16 W 32 A 4 W 2 W A PV system has a rated capacity of 10 kWp. The overall efficiency of this PV system is 75% . The average daily irradiance at the site is 4 kWh/m²/day. What is the expected average daily energy output of this system? 3 kWh 30 kWh 7.5 kWh 40 kWh
For most of the circuits, determine all the voltages and currents necessary this usually involves:(Eth, VR1, VR2) VB,VC,VE, VCE,VCB, IB, IC,IE, (I'C) Use Beta DC = 100
In the voltage regulator in figure 2 below, Vi=15V, Vz=10V, Ri=200 ohms, and Pz(max)=400mW. Determine Il, Iz, Ii, if Rl=350 ohms
Helli. I only need the last part. Plotting power vs voltage if used as a solar cell and give the definition of fill factor. Tnx
Estimate voltage E2 when E1=90sin2400t V, R1=R2=20 ohms, L1= L2=3mH and M=0.15mH
Using IC that is approximately equal to IE. Determine the value of R1in ohms, when VCC=19V, RC=2178 ohms, RE=327 ohms, VC=7 V and R2=6431ohm
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
In reference to the given figure, VCB = 10.3V and VBE = 0.7V. NOTES: VCB = VC-VB VBE = VB-VE In reference to Figure 1, what will be the ICq, in mA? In reference to Figure 1, what will be the voltage across RB, in volts?
GIVE DETAIL EXPLAIN PLEASE! with cicruit drawing.. Ans : Rth = 28 ohm Vth = 92 V.
Vcc =15V, R1 = 4800 ohm, R2 = 270000ohm, B = 90 Calculate IB , VC , VB , VCE
Two ideal CTs with turns ratios of 300 : 5 and 600 : 5 are connected as shown in Figure 3.6a and b. If the primary current is 3000A and the burden is 1 ohm, what are the voltages at the secondary terminals of the CTs in the two cases? Please answer in typing format please