Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Cable Beam com Rope Hinge

Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Cable Beam com Rope Hinge

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.5P: The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw...

See similar textbooks

Related questions

Q: The bar ABC is supported by a ball-and -socket at A and a slider bearing at C. Determine the…

A: In the free body diagram given, the coordinates of B are 0, 1830, 0 and the coordinates of D are…

Q: er no aden bne p lg dioe 7- Determine the maximum weight of the flowerpot that inqa can be supported…

Q: Operational Cable mass=15kg 5x %3D Aircraft Rudder 2.2361m (a)

A: Giveny4=5x or y=514x14y=2.2361mx=5mthe maximum permissible load of the cable , Pr=3kN=3000Nmass of…

Q: 01: Determine free body diagram and the forces for the equilibrium unloaded platform which has a…

Q: In your report you must include: (a) The free body diagram of the rudder. (b) If the maximum…

Q: Members AC and AB support the 300-lb crate. Determine the tensile force developed in member (AB).

Q: Determine the force in each member of the loaded truss. The force is positive if in tén 14 m 3 m 250…

A: To find force in all members of truss

Q: ~4%3D0.2 BA D 4m Hi =0.2 -7.5 m-

A: To determine the weight of the block D that can support the pole ABC.

Q: The members of a truss are pin connected at joint O. Determine the magnitude of F1 and its angle for…

A: From the vertical equilibrium of forces in the vertical direction,

Q: 0.25 m 0.25 m 1.5 m E 30° H D 10° 2 m 60° 0.5 m

Q: the tension developed in cables ABAB and ACAC cannot exceed 270 lb Determine the largest weight of…

Q: A pin-connected truss is loaded and supported as Determine shown in Fig The reaction at support E.…

A: Given , Free body diagram of the truss is

Q: The unstretched length of spring AB is 1 m. If the block is held in the equilibrium position shown,…

Q: diameter, weigh 5 kN and 13 kN, respectively.. nort rope and placed in water. What is the tension of…

A: Given: The diameter of each sphere = 1.3 m The weight of lighter sphere = 5 kN The weight of havier…

Q: Determine the reactions at A and B and the load required Q to hold bar AB in a horizontal position…

Q: Determine the force in each member of the space The support at A is a ball and truss shown in Fig.…

A: Consider the free body diagram of the given space truss as shown below.

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Determine the reaction components at the hinge support at Band the roller support at A due to the…

Q: Determine the magnitude of the horizontal force F and the support reactions at . If the cord CB ean…

A: Given: To determine: Reaction force at pin A

Q: Exercise 1- Determine the force developed in the member BC and reactions at the pin support A. Take…

Q: All two-force members of the loaded structure are of the same length. Member BCD is a rigid beam.…

Q: Determine the reactions at A and B and the load required Q to hold bar AB in a horizontal position…

Q: Entire frame, pulleys, and contacting cable to be isolated as a single unit. B L

Q: Draw the FBD of the following loaded cantilever and determine if it is a determinate structure.

Q: Members AC and AB support the 300-lb crate. Determine the tensile force developed in cach member. 4

A: Find the force in each member.

Q: 9 kN 2m

A: Given data, A cantilever beam of length 2 m having vertical load at free end.

Q: The unstretched length of spring AB is 2 m. If the block is held in the equilibrium position shown,…

A: Solution : Given data : unstretched length of spring AB is 2 m.

Q: Determine the reactions at the beam supports for the given loading.

A: Total reaction of uniform loading, R1 = 200 x 15 = 3000 lb total reaction of distributed loading, R2…

Q: The free body diagram of the rudder. (b) If the maximum permissible load that the steel operational…

A: in the problem we analysis of light aircraft rudder the rudder of an aircraft is usally found at the…

Q: Determine the tensile force developed in each member AB and AC .if Members have .support the 300-lb…

Q: Determine the force in each member of the loaded truss as a result of the hanging weight W = 265 lb.…

A: Given data, W = weight of the hanging block = 265 lb Point A is hinge support. So, one vertical…

Q: 14 Q1: The machine part of negligible weight is supported by a pin at A and a roller at Cas shown in…

A: find the support reaction at point A and point C.

Q: G E 4 ft [B 4 ft -4 ft 600 Ib 600 lb 800 Ib

A: It can be seen clearly from the figure that point G and A are hinge supported so there must be only…

Q: QU. Determine the support reactions on the member. The colar at A is fixed to the member and can…

A: Draw a free-body diagram of member AB. Apply equilibrium equation of forces in the horizontal…

Q: etermine the torce in each cable needed fo support the flowerpot nose weight is 10ON

Q: 1 ft 1 ft 2 ft Consider the given frame. В a) Determine the magnitude of the vertical reaction (Ib)…

A: Let CODE A lb=W lb Draw the overall free body diagram of the frame:

Q: Determine the magnitude of the horizontal force F and the support reactions at pin A.If the cord CB…

Q: The tractor shown in the figure has a weight of W... N is used to lift 900 N of gravel. Determine…

A: Given:Weight of tractor, W=388 kNWeight of gravels, w=900 N

Q: F 12 ft 3 ft 30 6 ft B -8.4 ft- 2.2 ft 1.4 ft The crane and driver have a weight of 2600 Ibs acting…

Q: Determine the force in hydraulic piston B and element AB. If a weight of W = 1500lb of the excavator…

Q: Each of the three steel wires has the same diameter. Determine the force in each wire needed to…

A: Given:-W=200 kgAD=DC=600mmDB=800 mmSame diameter To find:-Force in each wire.

Q: Members AC and AB support the 800-lb crate. Determine the tensile force developed in member (AB).

Q: al Ignoring the self-weight of the members, determine the support reactions.

A: we have to determine the reactions at A and D

Q: A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If…

A: mass=3tonne=3metric tonConsidering that the distances are in mmVertical Distance =180+1080=1.26m…

Q: Required Information The elevation and tit angle of table A8 are controlled by an operator's hand at…

Q: If the point M is at the centre of gravity of the body, the floating body will be in neutral…

A: This true false is related to the metacentric height concept of fluid mechanics. M- Metacentric…

Q: 100 kNm 20 kN/m A B

A: To determine the reactions.

Concept explainers

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.

Question

FN=130 MN=55 SN=130

Problem 7
Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value
of a = SN and b = MN meters. The equivalent of 0 is 30 degrees
Cable
Beam com
m
Rope
Hinge

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The homogeneous plate of weight W is suspended from two cables. Determine the force P that is necessary to keep the plate in the position shown.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the spring is unstretched when =80. If W=kL, the bar has three equilibrium positions in the range 0, only one of which is stable. Determine the angle at the stable equilibrium position.
The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
Develop a free body diagram based on the structure. There must be a system FBD and an FBD of one multi-force member.
The structure AB supports a suspended 2-Mg (megagram) mass. The structure isattached to a slider in a vertical slot at Aand has a pin support at B. What are thereactions at A and B?
The boxes each have mass m, and are held stationary by the systems of ropes and ideal (massless,frictionless) pulleys as shown. Shaded regions are fixed supports.Find the tensions in the labeled ropes.Express your answers in terms of mg. Show your work.You do not need to use the full recipe, but do draw free-body-diagrams!Please summarize your results in a table to make marking easier.
The platform scale consists of a combination of 3rd and 1st class levers sothat the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If x = 400mm, and the mass of the counterweight S is 3 kg, determine the mass of the load L required to maintain the balance. please include all free body diagrams.
*Show clearly all pertinent solutions and state the assumptions made, if any. Alie Abdul is nearing completion in assembling the giant robot doll. He needs to exert a 408.75N force on the pulley cable to lift the doll robot’s head (50kg) to attach to its body. Note: robot head’s weight is acting in the z- direction. a. Draw the FBD of the robot’s head. b.Determine the tensions in the four cables. Assume pulley E is frictionless.
The system shown is composed of an ABG bar, supported by a pin at point A and by a collar smooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and the Rod BDE is supported by a pin at D and a cable at end E. Calculate the load P, such that the cable force EF is 20lb.