Determine the void ratio if porosity 0.531

Q: Determine the horizontal component of the total hydrostatic force (kN) the water exerts on the gate…

A: To Determine Horizontal component of the total hydrostatic force , FH

Q: G

A:

Q: Each of the three frame bars in the figure has a linear mass of 12 kg/m. Locate the position (?̅,…

A:

Q: KIN, bad 50 KIN. SOive th with units. Example: XXX.XX

A: Given:- A=500mm2 Load 1=25kN load 2=50kN To find:- stress in part BC

Q: What is the Maximum moment in kN-m. Given: w 14, a 1, b = 6, and c 2. !! w kN/m A C D. -an bm cm

A:

Q: What is the Maximum moment in kN-m. Given: w1 = 48, w2 = 11, a = 2, b = 3, and c = 2. w1 kN/m w2…

A:

Q: Data for a single relationship (FTS) precedence network are given below. Construct the overlapping…

A: Given data: single relationship precedance network overlapping precedance network as follows

Q: 3. The following observations were made during the testing of a Dumpy level. Staff reading on B…

A: To Find :- RL of B Given :- RL of A = 432.052 m Instrument at        staff reading    Staff reading…

Q: Determine the void ratio if porosity 0.531

A: step 1-

Q: 5. Following is tabulated data that were gathered Temperature (C) Impact Energy (J) from a series of…

A: Part A

Q: Dear Form-Givers, As a future site supervisor, and eventually an architect, you are tasked to…

A: Sheet 1

Q: Determine the force in each member of the structure and establish whether the members are in tension…

A:

Q: 2. All members of the truss A В C shown have a cross- sectional area of 500 mm² and all pins have a…

A:

Q: ht meter simply supported beam carries a superimposed dead load of 6kN/m and a service live load of…

A:

Q: ne. T

A:

Q: npose phy ement and

A: Given:- BNBC 2020 To find:- physical and technical specification for:- a) cement b) MSRod

Q: d to excavate dry gravel H er the following situation: Bucket fill factor = 99 % Jltimate excavating…

A:

Q: The population of a certain community is known to increase at a rate proportional to the number of…

A:

Q: The T-beam has an effective flange width of 829 mm and the thickness is 125 mm. If the area of the…

A:

Q: 10 kN/m 90 kN 50 kNm 3 m 3 m 2 m 5m 4 m

A:

Q: A sample of dry sand was subjected to tri axial test with a confining pressure of 250 kN/m², The…

A:

Q: Example 9.36. Design a Zeolite-Softener for an industrial concern, using the following data : (i)…

A:

Q: o Why the tensilę strengths of concrete are of the order of 10 and 15%of the compressive'strength.

A:

Q: The T-beam has an effective flange width of 829 mm and the thickness is 125 mm. If the area of the…

A:

Q: Water

A:

Q: arry a design discharge of irrigation water of 90 . The slope of the canal is to be 0.002. The can o…

A:

Q: Which of the following best describes the historical order of development fo transporation…

A: Canada transportation is initially based on natural waterways and then followed by canal systems.…

Q: A three-hinged parabolic arch has a span of 30 m and the central rise is 5 m. It is subjected to a…

A:

Q: A reinforced concrete column 256 mm in diameter is designed to carry an axial compressive load of…

A: Determine the required number of reinforcing steel bars with a diameter of 20 mm.

Q: Describe what a balanced failure for a reinforced concrete beam is. Explain why designers do not…

A:

Q: 900 lb 400 lb 60 lb/ft D 4 ft RA 8 ft Rc 6 ft 8.

A:

Q: F В C D А 4.5 ft -3 ft 1.5 ft

A:

Q: What is the location of the Maximum moment from A in meters. Given: w1 43, w2 11, a 4, b 2, and c-…

A:

Q: 1. A 250mm x 300mm beam has a simple span of 12 meters. It is necessary to place a support at…

A: Deflection: The displacement of any structural element in the structure which is displaced under the…

Q: %3D What is the Maximum moment in kN-m. Given: w = 35, a = 4, b = 3, andc= 2. w kN/m A *cm Ro bm >…

A: Calculate the reactions and draw the shear force diagram point of zero shear will be the location of…

Q: Use F1 = 200 N/m; F2 = 150 N; L1 = 10 m; L2 = 6 m F1 A L1

A:

Q: 1. Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown…

A:

Q: If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column…

A:

Q: A student recorded the following number of paces after walking a distance of 54.269m repeatedly as…

A:

Q: What is the Maximum moment in kN-m. Given: w 17, a = 2, b 6, and c= 2. w kN/m CA >*-cm B D. kam b m

A:

Q: 5. Following is tabulated data that were gathered Temperature (C) Impact Energy (J) from a series of…

A: Part A

Q: Calculate the total length, L( m), so that the resulting stress q is uniform. А. 10 В. 12 С. 9 D. 8…

A: The diagram shows a beam of length L resting on a ground surface. The ground will exert a reaction…

Q: Solve for M, and Mg using integration in terms of w and L. MB MA A L –

A: In the above figure MA and MB are fixed end moments of a fixed beam loaded with uvl varying from 0-W…

Q: LINE LENGTH IN METERS BEARING AB 82.62 S60°43'E BC 111.41 N52°41'W CD 100.66 S71°43'W DE 62.97…

A: Transit Rule A rule for altering the traverse's closure mistake. The transit rule distributes the…

Q: 55 kN/m 3m pin 55 kN/m 5m 38.5 kN/m 4m 4m

A:

Q: 5 kN/m

A:

Q: Q1: The figure below represents a three sides polygon (ABC). Use the given information and answer…

A:

Q: Check for Plastic Section Modulus (Zx) and Plastic section Modulus (Zy) 50 150X50X25X2MM 25

A:

Q: Engineering Mechanics A  22-kg ladder with a span of 21 m is resting against a smooth wall at B and…

A: Given L=21 m  Mass of ladder is 21 Kg

Q: Find the weight of water if water content 0.55 and weight of soil solids is 51 g

A: The given question is related with geotechnical engineering . In this question we are provided with…

Pressure and Stress