Determine the volume of concrete of Girder G3 from gridline A/2-3 if there are 18identical spans in the plan.Consider the following plan and schedule.PLAN320068505750TC-1FIC-2S2S5S5S2S2$6*measurement is from center to center of the supportSCHEDULE OF BEAMS AND COLUMNSBEAM MARKB (mm)H (mm)G2500750G3500650ColumnDimension (mm)C-1600 x 600C-2750 x 750C-3900 x 900Select the correct response:2.41 m343.29 m338.46 m32.14 m3

Answered: Image /qna-images/answer/08357705-1527-466b-90d2-4018cd8f62c1.jpg

Determine the volume of concrete of Girder G3 from gridline A/2-3 if there are 18 identical spans in the plan. Consider the following plan and schedule. PLAN 3200 7400 6850 5750 8 (8 Tc-3 S2 S5 S5 S2 S2 S6 S6 *measurement is from center to center of the support SCHEDULE OF BEAMS AND COLUMNS BEAM MARK B (mm) H (mm) G2 500 750 G3 500 650 Column Dimension (mm) C-1 600 x 600 C-2 750 x 750 C-3 900 x 900 S9A S9A GIL

Determine the volume of concrete of Girder G3 from gridline A/2-3 if there are 18 identical spans in the plan. Consider the following plan and schedule. PLAN 3200 7400 6850 5750 8 (8 Tc-3 S2 S5 S5 S2 S2 S6 S6 *measurement is from center to center of the support SCHEDULE OF BEAMS AND COLUMNS BEAM MARK B (mm) H (mm) G2 500 750 G3 500 650 Column Dimension (mm) C-1 600 x 600 C-2 750 x 750 C-3 900 x 900 S9A S9A GIL

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Add 39 to all loads
PLEASE WRITE THE COMPLETE SOLUTION NEATLY: A rectangular beam has b=350 mm and an effective depth of 525 mm concretecompressive strength f’c = 17 MPa and steel yield strength fy = 276MPa, Calculate therequired tension steel area if the factored moment Mu = 150 KNm. Also recommendthe number of 20 mm diameter bars to be used. Draw/sketch the cross-sectional detailof the beam.
Determine the ultimate uniform load, wu of EACH beam indicated in the typical floor plan shown below. Assume all beams are carrying CHB wall except B5. Heigth of the wall is 3.25 m. Use load combination wu = 1.2DL + 1.6LL all beams. Assume the following design criteria: Concrete Slab = 23.6 KN/m3 Floor Finish = 0.05 KPa Slab Thickness: S1 = 0.125 m, S2 = 0.15 m Typical Interior Beam Sections = 200 mm x 400 mm Typical Exterior Beam Sections = 200 mm x 350 mm Ceiling System = 0.50 KPa 4” CHB both faces plastered (For Interior Walls) = 2.10 KPa 6” CHB both faces plastered (For Exterior Walls) = 2.73 KPa Residential Basic Floor Area Summarize all your load ouputs using table.
Find length, h, in inches of bronze post if beam must remain level
The client has unexpectedly to extend the span of the beam by 1.0m. Discuss what are you required to check and why?, to prove that the beam size and grade that has already been designed will still be adequate. HENCE span 3150mm. Grade of steel to be S275 to support the given loads mid span of beam Hence First and Second Floor Terrace = 1.5KN/m2
Civil. Estimate it please A room 600 cm long x 500cm wide have a flat roof. There is one T-beam in the centre (cross section below the slab 30 cm x 50cm) and the slab is 15cm thick. Estimate the quantity of iron bars required for reinforcement (for the T-beam only) from the data given below:- 8 Nos. 25 mm dia, in 2 rows of 4 each (all 4 in the bottom Main bars... being straight and others bent) 10mm dia and 15cm centre to centre throughout Stirrups Anchor bars 2 Nos. 16mm
Please answer asap! UPVOTE WILL BE GIVEN! WRITE THE COMPLETE AND DETAILED SOLUTIONS. This is already answered in Bartleby but the solutions is incorrect. Please don't follow it. Thanks- A simply supported 11-m span beam, 300-mm wide by 560-mm deep, is pre-stressed by straight tendons with Aps = 774 mm2 located 70 mm from the bottom at an iniitla prestress of 1.10 GPa. Calculate the concrete stress in MPa at the bottom fiber of the beam at midspan immediately after 16% losses in the tendons are in effect. Write your answer in 2 decimal places only. Use unit weight of concrete 24 kN/cu.m. Sign convention is (+) tension, (-) compression. Indicate the sign in your final answer.
Determine whether a W16 x 89 of A992 steelbeam shown is adequate.
What is the rule of thumb regarding purlin spacing? If the bay spacing is 24’ and the design loads are as follows: LL = 25 psf, DL = 5 psf and collateral load = 3 psf, what is the load on the purlins per foot. Does this look acceptable?
9. The reinforcement ratio of a section with 3-16 mm diameter tension bars, effective depth of 338 mm, and width of 280mm is nearest to a. 0.0064 b. 0.0055 c. 0.0076 d. 0.0123 10. Calculate the minimum reinforcement ratio for a given beam section if f’c=28MPa and fy=345 MPa. a. 0.00406 b. 0.00383 c. 0.00556 d. 0.00446 11. The minimum reinforcements need not be satisfied if As provided at every section is at least _______ greater than As required by analysis. a. 1/4 b. 1/2 c. 1⁄5 d. 1/3 12. For non-prestressed beams with Pu less than 0.10f’cAg, the strain at extreme layer of tension steel shall be at least a. 0.003 b. 0.002 c. 0.004 d. 0.005
Determine the net area along route ABCDEF for the C15 x 33.9 (Ag = 10.00 in2) shown in Fig. 3.8.Holes are for 3/4 in bolts.
A commercial sign is braced by struts AB and AC. Find the angle 'θ' between the struts