Benzene and Kerosene has a specific weight of 53 and 49 lb/cu.ft. respectively. The weight of benzene is 7.8 lb and their combined mixture has a specific weight of 51.5 lb/cu. ft. Determine the weight of kerosene in pound. Benzene and Kerosene has a specific weight of 53 and 49 lb/cu.ft. respectively. The welght of benzene is 7.8 lb andtheir combined mixture has a specific weight of 51.5 lb/tu.ft. Determine the weight of kerosene (in pound).

Answered: Determine the weight of kerosene in…

Engineering

Civil Engineering

Determine the weight of kerosene in pound.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Related questions

Q: L = 100 ft. A 100-ft long dam holds 30 ft of water as shown in the figure. w.s. a. Using the panel e...

Q: A circle has an equation of 22 +y? = 48. Compute the common area between the circle 2? + y? = 48 and...

Q: 6. Draw the moment diagrams using the method of superposition 5 kN/m 20 kN m 40 kN 12 m

Q: GUEN A 14 in - WIDE BY /2 10· THICK PLATE SUBJECTED TO TENSILE LOADING HAS STAGOERED HOLE As SHOION-...

Q: 1. Two lines XV and YV intersect at an inaccessible point V. Two points A and B are selected on line...

A: *Multiple Sub- parts* As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub...

Q: Flow occurs over the spillway of constant section as shown in Figure Q2(d). Given that yı, = 4.2 m a...

A: Spillway: It is a hydraulic structure which is used for the release of water from dam. They are loca...

Q: Show that F f | gL _H when resistance force (F) for a boat has related with a function of length L, ...

A: solutionUse buckingham pi theoremGiven parameteres Resisting force F; Length L; VelocityVacceleratio...

Q: Q.8 Fully saturated clay sample has (e = 1) and (Gs = 2.75), the %3D saturated unit weight (KN/m2) :...

Q: ate reactions C 20 kN 8 KN/m 2 m 1 m 4 m D.

A: Given: Simply supported beam with udl and point load. Total span =7m To find: Reaction at support A...

Q: Y 8 - 200 450 mm d' = 35 mm

A: Given data: fy=460 N/mm2d'=35 mm

Q: A metallic cantilever 150 mm wide, 200 mm deep and 2 m span carries a uniformly varying load of 50 k...

Q: A rectangular concrete beam section, 300 mm wide by 600 mm deep, is reinforced with 4-32 mm diameter...

Q: steel bar originally 200 mm long is pulled in tension with stress 150 MPa the magnitude of elastic m...

Q: What are the common minerals used in the manufacture of cement? Give a brief description of each min...

A: Introduction: Concrete is made up of of Portland cement. When portland cement is mixed with water to...

Q: Choose whether the statement is TRUE or FALSE. * TRUE FALSE The absolute pressure is equal to the ga...

A: Comment - As per our policy, we can only answer first three subparts of your question , kindly repos...

Q: HYDRAULICS

Q: Two runners start from rest, 250m apart. They run directly toward each other, both runners accelerat...

Q: ACTIVITY 2 Direction: solve and analyze each of the following pr 1. A thermometer reading 180C is br...

Q: Determine the compression index and expansion index Please show graph

A: We will solve this question in step no. 2

Q: Compute for the linear dead load of the masonry wall with cladding located on a floor with the follo...

A: Given, Storey height = 4m 2F Beam use W135x45 5' Concrete Hollow Blocks 12 mm thick Slat wall Panel ...

Q: Aggregate from three sources having the properties shown in table below were blended at a ratio of 2...

Q: Determine the momeny of inertia of the wetted surface of the dam. the unit must be in ft^4

Q: 1. (i) A dry soil has a void ratio of 0.65 and its grain specific gravity is = 2.80. What is its...

A: 1. i. Find Unit weight : γd = G*γw1 + e γd = 2.80 * 9.811 + 0.65 = 16.65 KN/m3

Q: 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section o...

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the exac...

Q: 25 lb 15 lb 1 ft

Q: W10

Q: If the liquid limit value of the experimental results is 70% and the plastic limit is 35%, and the c...

Q: G 67.5 kN 3.6 m -D -112.5 kN E 3.6 m IA B C 6 m +4.5 m Use portal method to analyze the frame. Deter...

Q: A rigid beam BC is suspended by links AB and CD. Determine the deflection at point E if the areas fo...

A: Given: The modulus of elasticity is 200 GPa. The area is 150 mm2.

Q: The gate shown is hinged through a point A and is res opening by a fixed ridge at point B. For a gat...

Q: 4. A closed, hollow, empty drum has a diameter of 24.0 in, a length of 48.0 in, and a weight of 70.0...

Q: a uniform gauge for the railway network of a country

Q: A sample of saturated soil has a water content of 35%. The specific gravity of solids is 2.65. Deter...

Q: 40 k F 20 k 5 ft D E 5 ft C В -5 ft- -5 ft- -S t- -5 ft- Determine the Vertical Reaction at A.

A: This question is related to the Structure Analysis. In this question we calculate the vertical react...

Q: 40. The following water content data are from several plastic limit tests for a soil. Determine PL o...

A: we will find water content for each test and take average.

Q: Consider a 4-m long, 4-m-wide, and 1.5-m-high aboveground swimming pool that is filled with water to...

A: solution Find the center of pressure h#=h¯+IG sin2θAh¯from the figure h¯=1.52=0.75mts

Q: Compute for the Bend Allowance and K-factor. 1. 213.06 Leg Length 1 84.11 R30 BA - Leg Length 2

Q: What is the significance of learning isometric and orthographic projections as a civil engineering s...

A: Significance of isometric and orthographic projection in Civil Engineering.

Q: If a particle has initial velocity of v0 = 12 ft/s to the right, at s0 = 0, determine its position w...

A: Given, v0 = 12 ft/s s0 = 0 t = 10 s a = 2 ft/s2 to left meaning retardation =-2 ft/s

Q: Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of spec...

A: Moisture content = Mass of moist aggregate - mass of oven dried aggregatemass of oven dried aggregat...

Q: he to The structure loaded as shuwn : he 4m P 40 KN E 200 GPa 12=1c_100 x 10° mm • Solve the reactio...

Q: Explain how radio signals broadcast by Global Positioning System satellites are used to calculate p...

Q: B

A: Moment area method is also known as mohr's method. It is applicable for both prismatic as well as no...

Q: For the reinforced concrete beam shown, calculate the bending stresses (fc, fs,and fs') in the concr...

Q: 5. Draw the shear moment diagram for the gable frame shown. Assume C is a hinge, and A and B are pin...

Q: 5) Determine the value of y in the manometer shown in the figure. 1m Alr, 5 KPa Oil S- 0.8 3 m 1 m W...

A: Given data in question Pressure of air Depth Specific gravity To find out Value of Y Note Density...

Q: PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 50 KN are applied at both plat...

A: We will divide force by resisting area to find stresses.

Q: A beam must span a distance of 12 feet and carry a uniformly distributed load of 120 ...

Q: A rectangular beam 300 mm deep is simply supported over a span of 4 metres. What uniformly distribut...

A: Depth of beam =300 mm deep is simply supported span length = 4 meters. to find the uniformly distri...

Q: A freight train starts from rest and travels with a constant acceleration of 0.5 ft/s 2. After a tim...

Concept explainers

Pressure and Stress

Question

Benzene and Kerosene has a specific weight of 53 and 49 lb/cu.ft. respectively. The weight of benzene is 7.8 lb and their combined mixture has a specific weight of 51.5 lb/cu. ft. Determine the weight of kerosene in pound.

Benzene and Kerosene has a specific weight of 53 and 49 lb/cu.ft. respectively. The welght of benzene is 7.8 lb and
their combined mixture has a specific weight of 51.5 lb/tu.ft. Determine the weight of kerosene (in pound).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
determine the specific weight density and specific gravity if a liquid thar occupies vol.if 200l and weighs 178kg.will this liquid float on surface if oil of specific gravity (0.8)? provide results. with SI units!
Convert 800mm of a certain liquid with sg=1.25 to a)oil of specific gravity equal to 0.80 and b) water
Solve the given problem using the equation of Combined gas law.1. Helium gas has a volume of 250 mL at 273Kat 1.0 atm. What will be the final pressure ( P2 ) if the volumeis reduced to 100 mL at 318K?2. The volume of a gas at 270C and 700.0 mmHg is 600mL.What is the final volume ( V2 ) of the gas at -200Cand 500.0 mmHg?
the reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. if the tank is 30 cm. deep, and is contaminated with 3.42 cm. of water at the bottom, how many meters of air remains at the top when the gage indicates "FULL"? use weight of: gasoline = 6.62 kN/m^3; air = 14.67 N/m^3. the tank is closed.
The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. If the tank is 30 cm. deep, and is contaminated with 3.05 cm. of water at the bottom, how many meters of air remains at the top when the gage indicates "FULL"? Use Unit weight of: gasoline = 6.24 kN/m3; air = 12.6 N/m3. The tank is closed. ANSWER : 0.017
Civil P- Determine the density of liquid methanol in pounds per cubic foot (lb/ft3) using the information below, and translate the SI values for heat capacity, thermal conductivity, and viscosity into English units.Specific gravity ¼ 0.92 (at 608F)Density of reference substance (water) ¼ 62.4 lb/ft3 (at 608F)Heat capacity ¼ 0.61 cal/g.8C) (at 608F)Thermal conductivity ¼ 0.0512 cal/m . s . 8C)Viscosity ¼ 0.64 cP (at 608F)
Determine the mean effective pressure in kPa of a certain air -standard Diesel cycle which has a compression ratio of 16 and a cutoff ratio of 2. At the beginning of the compression process, the pressure and temperature of air is at 95,000 Pa and 300K, respectively. Roun-off your answer into two decimal places. Hint: Linear Interpolation equation
3. The system in Figure 2-5 is at 20oC. If atmospheric pressure is 101.03 kPa and the absolute pressure at the bottom of the tank is 231.3 kPa, what is the specific gravity of olive oil? Note: density of water=9.79 kN/m3 (specific gravity SAE oil is 0.89, h SAE oil is 1.5m, h water is 2.5m, H olive oil is 2.9m, h mercury is 0.4m) and use g=9.79m/s2. a) 1.39 b) 1.29 c) 1.49 d) 1.59 e) none of the above
There are four liquids that are to be poured in a single vessel that is located in an atmosphere with g = 3.72m/s2. The first liquid is seawater (SG=1.025), the second is kerosene (ρ=1.591 slugs/ft3), the third is castor oil (SG=0.959), and the last liquid is liquid butane (unit weight = 2235.72N/m3 @ g=3.72m/s2). (a)Determine the density of seawater, the specific gravity of kerosene, the unit weight of castor oil and the density of liquid butane expressing all your answers in SI Units. (b) Illustrate the order of the liquids from the top-to-bottom of the vessel?
3.5 kg of an ideal gas is heated at constant temperature from 15 m3 and 4.0 atm to 35 m3 at Determine the work done
Civil The height of a liquid column of mercury open to the atmosphere is 2.493 ft. Calculate the absolute pressure at the base of the column 1B_{t} / f * t ^ 2 psia, mm Hg. and in H-O. Assume that the density of mercury is 848.7 lb/ft and atmospheric pressure is 2116 lb/ft² absolute.