Determine the x- and y-coordinates of the centroid of the shaded area. 95 -150- 95 140 Dimensions in millimeters Answers: (X, Y) = ( i ) mm i

Q: 390 lb 1312 800 lb · ft - 8 ft- -4 ft- 3 ft 30°% BO 8 to 10. Draw the free-body diagram of member…

A:

Q: The coefficient of kinetic friction under block A in Fig. 24-A is 0.30 and under block B is 0.20.…

A:

Q: F3 = 750 N 45° 5 30° F2 = 625 N F = 850 N

A:

Q: A 90-hp (shaft output) electric car is powered by an electric motor mounted in the engine…

A: find the rate of heat supply to the engine.

Q: For a maximum cycle temperature of 3000°R, determine: (a) the heat addition to the cycle, in Btu.…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: A solid steel shaft, circular in cross section, has a change in diameter from 135 mm to 90 mm with a…

A:

Q: A continuous rope is pulled by a drum A (d=5 inches) which rotates at constant speed in the…

A:

Q: Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic…

A: Write the given data. P1=14 lbf/in2T1=520°R Here, P1 is the initial pressure at entry and T1 is the…

Q: The steel rails for a railroad track (E, = 29 x 106 psi, a, = 6.5 x 106/°F) were laid out at a…

A:

Q: Consider a two degree of freedom bar elements as shown in figure. Using finite element method to…

A: formulate the equilibrium equation for the given system using finite element method.

Q: Mechanical Engineering There is a spring with a repeated compressive load between 50N and 100N.…

A: according to the details provided

Q: 3. 130 Consider a Rankine cycle with reheat as shown in the diagram, with state properties as…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: A stainless steel pipe with a length of 35 ft has an inner diameter of 0.92 ft and an outer diameter…

A:

Q: What is the largest safe torque, in Nm, can be applied to the circular cross-section?(Provide answer…

A:

Q: The 60-kg man with center of mass G supports the 34-kg drum as shown. Find the greatest distance x…

A:

Q: For the system shown in the Figure, Reservoir I has a water depth of 7 m and Reservoir 2 has a water…

A: INTRODUCTION : The head losses occur in pipes when the area of the crosssection occurs in the pipe…

Q: A cargo truck with a weight of 289 kN was raised using a hydraulic press. If oil acts on a piston…

A: Correct answer: 1148.62 kPa

Q: A building is being heated through the help of a Carnot heat pump and is required to be maintained…

A: Correct answer: 2.56 kW

Q: Determine the x- and y-coordinates of the centroid of the shaded area. y 520 150 60° 60° 370 185 260…

A:

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Determine (a) the shear stress in the rivets and (b) the thickness "t" of the steel plate if the…

A: find the shear stress in rivets and thickness of plate.

Q: Prove that the difference between x and h is when a rectangular plate is immersed in liquid as shown…

A: When a rectangular plate is immersed in liquid as illustrated in figure, we must establish that the…

Q: 10. How long after it first left did it take this object to travel back to its starting point? 30 E…

A: Correct answer: t = 100s

Q: A vertical semi-circular area of radius r is submerged in a liquid with its diameter in the liquid…

A:

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

A:

Q: An Actual Reheat Cycle with one-stage reheating is executed with steam expanding initially from the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Determine the chain speed in meter/sec of an rc 80 on a 21-tooth sprocket turning at 600 rpm.

A: find the speed of chain.

Q: 5. If 528 kJ of heat are added to 2.5 kg of helium at constant volume process when the initial…

A:

Q: An electrical wire with a length of 5-m and 3.5-mm-Ø spreads over one room at 18°C. Heat is…

A:

Q: SITUATION 8 Determine the critical hydraulic gradient of a coar se- grained soil if buoyant unit…

A: find the critical hydraulic gradient of a course-grained soil.

Q: Consider a 10 cm wall made of polyurethane board (k = 0.0260 W/m.K) which is exposed to still air (h…

A: Given:L=10 cm =0.1 mk=0.0260 W/m.Khi=9.37 W/m2.Kho=34 W/m2.K

Q: A flanged bolt coupling is used to connect a solid shaft 86 mm in diameter to a hollow shaft 100 mm…

A: INTRODUCTION : Flange coupling is the process of joining two shafts or tube ends in a flush, sealed…

Q: he maximum bending stress of a hollow shaft is equivalent to 80 N/mm2, while the maximum shear…

A:

Q: 2. Liquid hydrocarbon fuel, C16H43 is burned with 25% excess air. Calculate the actual air fuel…

A: Stoichiometric air is calculated and then actual air is found. Finally, A/F ratio is calculated.

Q: Situation 02. A crate has a mass of 120kg and the coefficient of static and kinetic friction is 0.60…

A:

Q: Problem 1: Calculate the forces in the required members of the truss shown: F1 F2 F3 H G F h A F4 В…

A:

Q: The assembly shown in the figure consists of a brass core (diameter d1 = 0.25 in.) surrounded by a…

A:

Q: A water tank with semi-elliptical end plates is filled with water (the unit weight of water is 62.4…

A: Given data, Geometry of the elliptical plate is x29+y216=1 So, Radius of semi-minor axis, a = 3 ft…

Q: Prove that the difference between x and h is when a rectangular plate is immersed in liquid as shown…

A:

Q: Determine the moment of nertia of the overhung crank about the z as The materal is steel havng a…

A:

Q: The Working fluid in heat pumps is called _______   Which is not a thermal energy sink a.…

A:

Q: What force F on the rope is required to start lifting body A (20ON) given that thi to the wedge…

A:

Q: Determine the coordinates of the centroid of the shaded area. 1.7" 2.2" 5.4"- Answers:

A: To determine the centroid of the composite area.

Q: Q3) A constant volume fuel air cycle with a compression ratio of 8, the A/F=15:1. The pressure…

A:

Q: Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A: find the centroid of the section and moment of inertia about centroidal x- axis.

Q: The pressure at a point in the seawater is 100 kPa, determine the pressure in kPa 33.43 meters below…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.