Develop the shear and bending moment diagrams for the beam 6 kN/m 2.4 kNm B 4 m .6m.

Q: For this mechanism, locate all the instant centers using Kennedy's theorem. Upload complete…

A:

Q: Situation #1: The initial angular velocity of the compound pulley B is 6 rad/s counterclockwise and…

A:

Q: Assume you are bending a 3/16” thick rolled plate of Al 6061-T6 at a 90-degree angle. The initial…

A: Solution: Given Data: t=316"Ri=0.35"   Note: Yield strength of Al 6061-T6 is: Sy=35000 psi Young's…

Q: 1-75. The hangers support the joist uniformly, so that it is assumed the four nails on each hanger…

A:

Q: In a Rankine cycle, the condition of steam leaving the turbine could be any of the following except…

A:

Q: A particle is moving along a circular path having a radius of 4 inches such that its position as a…

A:

Q: 4. Repeat problem 3 assuming that the column is made of wood for which E = %3D 10 GPa. Ans. 81.34 mm

A: Given   Force, F = 40 kN Length, L = 3 m              E = 10 GPa Find   Length, b

Q: A solid cylindrical steel rod is made from three portions as shown in Fig Q5b. It is subjected to a…

A:

Q: A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 620 mm?. If…

A:

Q: The two blocks are released from rest when r = 1.0 m and 0 = 30°. Neglecting the mass of the pulley…

A:

Q: The column of a circular cross section is expected to buckle

A:

Q: A system consisting of 2 kg of ammonia undergoes a cycle composed of the following processes:…

A: Given data as per the question Mass of ammonia , m=2kgInitial pressure,P1=10barDryness…

Q: A spring subjected to torsional stress is made of hard-drawn brass wire. The ultimate strength in…

A: Spring are used to absorb energy or restored it slowly or rapidly according to the function of a…

Q: The column of a circular cross section is expected to buckle ►y Around x-x Around y-y Around any of…

A: Circular cross section buckle around that axis moment of inertia is minimum. Here Ix=Iy<Iz…

Q: Three field quantities are given by: P = 8ax -az Q = 2ax – Gay + 2az %3D R %3D Sаx - Зау + saz…

A:

Q: A line shaft is to transmit 200 hp at 900 rpm. If the line shaft is connected to a 2” counter shaft…

A: Given Data: Diameter of the countershaft, d=2 inch

Q: The transmitted torque of a 100 mm steel shaft is 5 kN-m and the maximum bending moment is 3 kN-m.…

A:

Q: Q1. What is the linear momentum for particle A (kg.m/s)? (A) +4i+6j+6 k (B) - 4 i+6j+6 k (C)…

A: Mass of particle A is not given. please provide full question. we can solve second part for you.…

Q: 10 ksi, oy -4 ksi, and o, = 8 ksi. Using E = The normal stresses at a point in a steel member are o,…

A: Answer: The normal strain along z is (0.2138 × 10-3) in/in.

Q: A uniform ladder of length L and weight w is leaning against a vertical wall. The coefficient of…

A:

Q: The pressure and temperature of air change from (4.00x10^0) bar to (1.5000x10^0) bar and from…

A: P1= 4 barP2= 1.5 barT1= 806 KT2= 438 KAir flow rate, m˙= 1 kg/sCp= 1005 J/kgKR= 287 J/kgK

Q: Problem 3) Determine the reactive forces at A and B. 14 kN E 2 m 16 kN F 2 m A B.

A: From equilibrium conditions for above fbd

Q: Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the…

A:

Q: 5. A wheel revolving at 18 rev/sec has an angular acceleration of 12 rad/sec? . find the number of…

A:

Q: Difference between these two formula of capillary rise h= (2σcosθ)/(rγ) and h= (4σcosθ)/(rγ)

A:

Q: Question 3 (a) A two-dimensional flow velocity field in the domain with non-dimensional coordinates…

A: From the provided velocity equation,

Q: A container is occupied by a ten kg water and four kg vapor at 0.88 MPa. Determine (a) its…

A:

Q: A hollow shaft carries a torque 3.4 kN-m at a shearing stress of 55 MPa. The outside diameter is…

A: Determine the inside diameter in mm.

Q: Problem 1) Determine the spring constant, k if the unstretched length of the spring is 3.2 meters…

A: Given Data: Unstretched length, L=3.2 m

Q: Water flows through a pipe at 130 L/s that changes gradually in diameter from 154 mm at point A to…

A:

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

A:

Q: A container with an internal volume of 2.94 m³ is occupied by a ten kg steam at 0.88 MPa with an…

A:

Q: Find the steady state temperature distribution in the semi infinite plate shown below. The 2D steady…

A: Fins are always required to be used only when the convective heat transfer coefficient h are…

Q: A point is located in a polar co-ordinate system by the co-ordinates r = 2.5 m and 0= 35°. Find the…

A: From polar coordinates to Cartesian coordinates conversation technique

Q: rh not O Trot = 75°C %3D Tout-? hcold O Teota = 18°C %3D Hot and cold stream of water are mixing…

A:

Q: Two cars moving on the same direction have a velocity of 90 ft/sec. Car A is 100 feet behind car B.…

A: Given data  the velocity of cars A and B are  90 ft/sec   To determine  required acceleration of…

Q: Determine the diameter of 12 ft long steel line shaft which is subjected to a bending action due to…

A: Question: Determine the diameter of 12 ft long steel line shaft which is subjected to a bending…

Q: The 700 N skier is schussing on a 25° slope. At the instant shown, he is moving at 20 m/s. The…

A:

Q: Current Attempt m ogress For what value M of the clockwise couple will the horizontal component A,…

A:

Q: (97) Derive the equations of motion of the system shown in the figure below using Lagrange's…

A:

Q: Which of the following working fluids could NOT used in a reverse Brayton cycle operating betwe…

A: Answer is steam.

Q: 2.5 m 2 m/s 1.0 m Fig. P13.10 3.10 The firehose is being uncoiled from its reel at the constant…

A: Answer: The normal component of acceleration of point A on the rim of the reel : (a) at the instant…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: Let's assume the rocket has a rest length of 57 m and the hangar has a rest length of 51 m.…

A:

Q: For the mechanism below, at this instant, angle 0 = 30°, rod BC has angular velocity W = 4.1 rad/s,…

A:

Q: A fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill.a water tank as…

A: Given Data The discharge is:Q=0.00156 m3/s The diameter of the pipe is:d=0.025 m The density of the…

Q: An aircraft has a total mass of (8.800x10^1) kg and a wing area of (3.00x10^1) m2. It operated with…

A:

Q: Problem Set – Temperature Change 2. Based on the figure below, a steel rod was fitted on the copper…

A:

Q: What is the specific enthalpy (kJ/kg) and specific entropy (kl/kg-K) of a steam with a specific…

A:

Q: Find the general solution for the following first order D.Es? b) x*dy + (y? - xy)dx 0 d) (x + xy -…

A: